2008 HONDA PILOT Code

Press and hold the remote
transmitter button and one of the
HomeLink buttons at the same
time.transmitter button and one of the
time. While continuing to hold the
HomeLink button, press and
release the remote transmitter
button every 2 seconds.If the red indicator in HomeLink
continues to f lash slowly (does
not f lash rapidly), your remote
transmitting after a short time.
If the red indicator in HomeLink
begins to f lash slowly at f irst,
then rapidly, release both If the red indicator in HomeLink
then rapidly, release both
If the red indicator in HomeLink
not begin to f lash rapidly),
184
\f—\f—\fy

y
(+\fy\f
y
Homelink® Universal Transceiver
2.
buttons, and go to step 4. Go to step 3.
transmitter may stop
Press and hold the remote
HomeLink buttons at the same
begins to f lash slowly at f irst,
3.
buttons, and go to step 4.
repeat steps 1 thru 3.
continues to f lash slowly (does
µ
If you just
received your vehicle and have not
trained any of the buttons in
HomeLink bef ore, you should erase
any previously learned codes bef ore
training the first button. To do this,
press and hold the two outside
buttons on the HomeLink
transceiver for about 20 seconds,
until the red indicator f lashes.
Release the buttons, then proceed to
step 1.
If you are training the second or
Holdtheendof thegaragedoor
inches f rom HomeLink. Make
sure you are not blocking your
view of the red indicator in
HomeLink.
1.
Bef ore you begin
third buttons, go directly to step 1.
opener remote transmitter 1 to 3
T raining HomeL ink
2008 Pilot

Make sure you have properly
completed the ‘‘Training
HomeLink’’ procedure.
location will vary, depending on
the manufacturer.Press and hold the button on
HomeLink f or 3 to 4 seconds.
f or about 1 second. It should
operate the garage door.
The ‘‘Training HomeLink’’
procedure trains HomeLink to the
proper garage door opener code.
The f ollowing procedure
synchronizes HomeLink to the
garage door opener so it sends and
receives the correct codes.
For security purposes, newer garage
door opening systems use a ‘‘rolling’’
or variable code. Information from
the remote control and the garage
door opener is needed bef ore
HomeLink can operate the garage
door opener.
garage door opener unit until the
indicator next to the button comes
on. The indicator may blink, or
comeonandstayon.Youthen
have approximately 30 seconds to
complete the f ollowing steps.
2. 4.
1.
T raining With a Rolling Code
System
Features
185
TRAINING BUTTON
\f—\f—\fy

y
(+\fy\f
\fy
Homelink® Universal Transceiver
garage door opener unit. The
Find the ‘‘l earn’’ button on your 3. Press the “learn” button on the
5. Press the HomeLink button again
If the button works,
programming is complete.
If the button does not work go
operate any other compatible
remotely controlled device around
your home (lighting, automatic
gate, security system, etc.).
pushing it for about 1 second.
to step 5.
5. PushandholdtheHomeLink
f or 2 seconds then stays on, you
Code System’’ (see page 185).
button and watch the red indicator
on Homelink.
If the indicator stays on, press
If the indicator f lashes rapidly
the Homelink button again; the
have a rolling code transmitter:should operate.
remotely controlled device
other two HomeLink buttons to go to ‘‘Training with a Rolling
6. Repeat these steps to train the
4.
Test the Homelink button by
2008 Pilot

As required by the FCC:This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.
Toerasethecodesstoredinallthree
buttons, press and hold the two
outside buttons until the red
indicator begins to f lash, then
release the buttons.
Youshoulderaseallthreecodes
bef ore selling the vehicle.
If you want to retrain a programmed
button f or a new device, you do not
have to erase all button memory.
You can replace the existing memory
code using this procedure:
If a rolling code transmitter was
previously programmed, the
indicator will f lash rapidly f or 2
seconds, and then stay on f or
about 23 seconds. If a standard transmitter was
programmed, the indicator will
stay on f or about 25 seconds.
Press and hold the HomeLink
button to be trained until the
HomeLink indicator begins to
flash slowly. If you have problems with training
the HomeLink Universal Transceiver,
or would like inf ormation on home
products that can be operated by
HomeLink, call (800) 355-3515. On
the Internet, go to
www.homelink.com.
HomeLink
is a registered
trademark of Johnson Controls, Inc. Once the HomeLink indicator
begins to f lash slowly, continue to
hold the HomeLink button, and
‘‘Training HomeLink’’ (see page
).
1. 2.
184
Erasing Codes
Retraining a Button
Customer Assistance
186
\f—\f—\fy

y
(+\fy\f

y
follow steps 2 thru 5 under
Homelink® Universal Transceiver
2008 Pilot

If the engine does not start within
15 seconds, or starts but stalls
right away, repeat step 4 with the
accelerator pedal pressed halfway
down. If the engine starts, release
pressure on the accelerator pedal
so the engine does not race.
If the engine fails to start, press
the accelerator pedal all the way
down, and hold it there while
starting to clear flooding. If the
engine still does not start, return
to step 5.
Without touching the accelerator
pedal, turn the ignition key to the
START (III) position. Do not hold
the key in the START (III)
position f or more than 15 seconds
at a time. If the engine does not
start right away, pause for at least
10 seconds bef ore trying again.
Make sure the shif t lever is in
Park. Press on the brake pedal.
In cold weather, turn of f all
electrical accessories to reduce
the drain on the battery.
Apply the parking brake.
When you start the engine, check
the gauges and indicators in the
instrument panel (see page ).
Fasten your seat belt. Check that
your passengers have f astened
their seat belts (see page ).
Make sure the doors and the
tailgate are securely closed and
locked.
Check the steering wheel
adjustment (see page ).
Check the adjustment of the
inside and outside mirrors (see
page ). 5.
6.
1.
2.
3.
4.
15
6.
7.
8.
9.
10. 92
78
61
Driving Guidelines, Starting the Engine
Starting the Engine
Driving
205
The engine is harder to start in cold
weather. Also, the thinner air f ound at
altitudes above 8,000 f eet (2,400
meters) adds to this problem.
T he immobilizer system protects your
vehicle f rom thef t. If an improperly-
coded key (or other device) is used, the
engine’s f uel system is disabled. For
more inf ormation, see page . 80
\f—\f—\fy

\fy
(+\fy\f
\fy
2008 Pilot

If the remaining engine oil lif e is 15
to 6 percent, you will see the engine
oil lif e indicator every time you turn
the ignition switch to the ON (II)
position. The maintenance minder
indicator will also come on, and the
maintenance item code(s) for other
scheduled maintenance items
needing service will be displayed
next to the engine oil lif e indicator.The 15 and 10 percent oil lif e
indicators remind you that your
vehicle will soon be due f or
scheduled maintenance.
When the remaining engine oil lif e is
5 to 1 percent, you will see a
‘‘SERVICE’’ message along with the
same maintenance item code(s),
everytimeyouturntheignition
switch to the ON (II) position.
Maintenance Minder
238
MAINTENANCE
MINDER
INDICATOR
ENGINE OIL LIFE
INDICATOR
MAINTENANCE
ITEM CODE(S) ‘‘SERVICE’’ MESSAGE
\f—\f—\fy

y
(+\fy\fy
2008 Pilot

If you do not perf orm the indicated
maintenance, negative mileage is
displayed and begins to blink af ter
the vehicle has been driven 10 miles
(10 km) or more.
Immediately have the indicated
maintenance done by your dealer.
Negative mileage means your
vehicle has passed the maintenance
required point.
When the remaining engine oil lif e is
0 percent, the engine oil lif e indicator
will blink. The display comes on
everytimeyouturntheignition
switch to the ON (II) position. The
maintenance minder indicator
( ) also comes on and remains
on in the instrument panel. When
you see this message, immediately
have the indicated maintenance done
by your dealer.
The maintenance item code or codes
indicate the main and sub items
required at the time of the oil change
(see page ).
You can switch the information
display f rom the engine oil lif e
display to the odometer or the trip
meter. Press and release the select/
reset knob on the instrument panel.
Whentheengineoillifeis15to1
percent, the maintenance minder
indicator ( ) comes on every
time you turn the ignition switch to
the ON (II) position, then it goes out
if you switch the inf ormation display.
When you see this message, have
the indicated maintenance
perf ormed by your dealer as soon as
possible.
240
Maintenance Minder
Maint enance
239
NEGATIVE MILEAGE
\f—\f—\fy

y
(+\fy\fy
2008 Pilot

Your dealer will reset the display
af ter completing the required
maintenance service. You will see
‘‘OIL LIFE 100%’’ on the inf ormation
display the next time you turn the
ignition switch to the ON (II)
position.
If maintenance service is done by
someone other than your dealer,
reset the maintenance minder as
f ollows:Turn the ignition switch to the ON
(II) position.
Press the select/reset knob
repeatedly until the engine oil lif e
is displayed.
All maintenance items displayed on
the inf ormation display are in code.
For an explanation of these
maintenance codes, see page .
You can change the inf ormation
display f rom the engine oil lif e
display to the odometer, the trip
meter, or the outside temperature (if
equipped) every time you press and
release the select/reset knob.
When the engine oil lif e is 0 percent
or negative mileage, the
maintenance minder indicator
( )remainsonevenif you
change the inf ormation display.
Immediately have the service
perf ormed, and make sure to reset
the display as described on the
f ollowing.
1.
2.
243
Maintenance Minder
Resetting the Engine Oil Lif e
Display
Maintenance Main Items and Sub
Items
240
MAINTENANCE MAIN ITEM
MAINTENANCE SUB ITEM
\f—\f—\fy

y
(+\fy\fy
2008 Pilot

CONT INUED
If you have the required service
done but do not reset the display, or
reset the display without doing the
service, the system will not show the
proper maintenance intervals. This
canleadtoseriousmechanical
problems because you will no longer
have an accurate record of when
maintenance is needed.
Your authorized Honda dealer
knows your vehicle best and can
provide competent, ef f icient service.
Press the select/reset knob f or
another 5 seconds. The
maintenance item code(s) will
disappear, and the engine oil lif e
will reset to ‘‘100.’’
Press the select/reset knob f or
about 10 seconds. The engine oil
lif e and the maintenance item
code(s) will blink.
4.
3.
Maintenance Minder
Important Maintenance
Precautions
Maint enance
241
\f—\f—\fy

y
(+\fy\fy
2008 Pilot