2008 HONDA FIT lock

If you tow your vehicle with an
automatic transmission, the Honda
Genuine ATF-Z1 transmission f luid
must be changed every 2 years or
30,000 miles (48,000 km), whichever
comes f irst.Move the shifter into the Neutral
position.
Release the parking brake.
Leave the ignition switch in the
ACCESSORY (I) position so the
steering wheel does not lock.
Make sure the radio is of f , and
remove any item plugged into the
accessory power socket so you do
not run down the battery.
1.
2.
3.
4.Manual transmission:
Towing Your Vehicle Behind a Motorhome
Driving
175
\f—\f—y\f\f\fy
(
\fy\f
\fy
2008 Fit

Remove the oil f ilter, and let the
remaining oil drain. A special
wrench (available from your
dealer) is required.
Make sure the oil f ilter gasket is
not stuck to the engine block. If it
is, remove it bef ore installing a
new oil f ilter.
Install a new oil f ilter according to
the instructions that come with it.Put a new washer on the drain bolt,
then reinstall the drain bolt.
Tighten the drain bolt to:
Refill the engine with the recom-
mended oil.
Engine oil change capacity
(including f ilter):
Replace the engine oil f ill cap.
Start the engine. The oil pressure
indicator should go out within 5
seconds. If it does not, turn of f the
engine, and check your work.
Let the engine run f or several
minutes, then check the drain bolt
and oil f ilter f or leaks.
Turn of f the engine and let it sit
f or several minutes, then check
the oil level on the dipstick. If
necessary, add more oil.
3. 5.
6.
7.
8.
4. 9.
Changing the Engine Oil and Filter
Maint enance
189
OIL FILTER
29 lbf·ft (39 N·m , 4.0 kgf·m)
3.8 US qt (3.6
)Improper disposal of engine oil can be
harmf ul to the environment. If you
change your own oil, please dispose of
the used oil properly. Put it in a sealed
container and take it to a recycling
center. Do not discard it in a trash bin
or dump it on the ground.
\f—\f—y\f\fy
(
\fy\f
y
2008 Fit

The coolant level should be up to
the base of the f iller neck. Add
coolant if it is low.
Pourthecoolantslowlyand
caref ully so you do not spill any.
Clean up any spill immediately; it
could damage components in the
engine compartment.Do not add any rust inhibitors or
other additives to your vehicle’s
cooling system. They may not be
compatible with the coolant or
engine components.
Pour coolant into the reserve tank.
Fill it half way between the MAX
and MIN marks. Put the cap back
on the reserve tank.
Make sure the engine and radiator
are cool.
Relieve any pressure in the cooling
system by turning the radiator cap
counterclockwise, without
pressing down.
Remove the radiator cap by
pushing down and turning
counterclockwise. Put the radiator cap back on, and tighten it fully.
3. 4.
2.
1.
5.6.
Engine Coolant
Maint enance
191
RADIATOR CAP
RESERVE TANK
\f—\f—y\f\fy
(
\fy\f
y
2008 Fit

Use a f lat-tip screwdriver to
remove the holding clip f rom the
inner f ender, then pull the inner
f ender cover back.
To change the bulb on the driver’s
side, start the engine, turn the
steering wheel all the way to the
right, then turn of f the engine. To
change the bulb on the passenger’s
side, turn the steering wheel to the
lef t.
Reinstall the inner f ender cover.
Then reinstall the holding clip, and
lock it in place by pushing on its
center.
Push the electrical connector onto
the new bulb. Make sure it is
connected securely. Turn on the
headlights to test the new bulb. 1.
2.
9.
10.
Lights
Replacing a Parking L ight/Front
Side Marker Bulb and a T urn
Signal Light Bulb
198
HOLDING CLIP
\f—\f—y\f
y
(
\fy\f\fy
2008 Fit

Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Reinstall the socket into the light
assembly by turning it clockwise
until it locks.Turn on the lights to make sure
the new bulb is working.
Reinstall the inner f ender cover.
Then reinstall the holding clip, and
lock it in place by pushing on its
center.The f og lights use halogen bulbs.
When replacing a bulb, handle it
carefully. See page for more
inf ormation.
3.
4.
5. 6.
7. 196
CONT INUED
On Sport model
ReplacingaFogLightBulb
Lights
Maint enance
199
PARKING LIGHT/FRONT SIDE MARKER
BULB
TURN SIGNAL LIGHT BULB
\f—\f—y\f\fy
(
\fy\f\fy
2008 Fit

Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the f og lights to test the
new bulb.
Reinstall the f og light assembly,
then tighten the screw.
Use a Phillips-head screwdriver to
remove the screw.
To remove the f og light assembly,
slide it inward, then caref ully pull
it out of the bumper. Remove the electrical connector
f rom the bulb by squeezing the
connector to unlock the tab, then
slide the connector of f the bulb.
Remove the bulb by turning it
about one-quarter turn
counterclockwise.
1.
2.
3.
4.5.
6.
7.
8.
Lights
200
ELECTRICAL CONNECTOR
SCREW
\f—\f—y\f
y
(
\fy\f\fy
2008 Fit

Open the tailgate. Place a cloth on
the edge of the light assembly
cover. Remove the cover by
caref ully prying in the notch on its
middle edge with a f lat-tip
screwdriver.Determine which of the f our bulbs
is burned out: stop/taillight, back-
up light, turn signal light, or
taillight.
Remove the socket by turning it
one-quarter turn counterclockwise.Remove the burned out bulb f rom
the socket by pulling it straight out
of its socket.
Install the new bulb in the socket.
Turn on the lights to make sure
the new bulb is working.
Reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Reinstall the light assembly cover.
1. 2.
3.4.
5.
6.
7.
8.
Replacing Rear Bulbs
Lights
Maint enance
201
LIGHT ASSEMBLY COVER
\f—\f—y\f
y
(
\fy\f\fy
2008 Fit

Open the tailgate. Remove the
light assembly cover by pushing in
the tabs on both sides and pulling
the cover of f .
Remove the socket f rom the light
assembly by turning it one-quarter
turn counterclockwise.Put the socket back into the light
assembly, and turn it clockwise to
lock it in place.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Press the brake pedal to make
sure the new bulb is working. Put the cover back on the light
assembly. Push it in until it locks
in place.
1.
2. 3.
4.5.
6.
Replacing a High-mount Brake
Light Bulb
Lights
202
\f—\f—y\fy
(
\fy\f\fy
2008 Fit