2008 GEELY MK steering

Power Steering System-Steering Drive and Control Mechanism4-69Section 2 Steering Drive and Control MechanismComponent ViewDriverÕs airbag module
Left combination switch
Steering column assembly
Steering column spline dust shield Steering column lower cover Steering column upeer coverRight combination switch
Clock spring
A/T:Parking lock cable33-5933-5922-2922-2916-26 3-spoke steering wheel car
Steering wheel assembly (optional)4-spoke steering wheel car
Quncunx cap screw
Steering wheel assembly
Quincunx cap screw
Slidefork #2 counter shaft
specified torqueN.
m :

Component ViewIgnition switch cylinder
Conical head bolt
snap ring
Upper and lower Steering
column panel
Ignition switch bracket
Ignition switch assembly
snap ring Steering column
Main shaft¡ôMain shaft bearing A/T lock cablePower Steering System-Steering Drive and Control Mechanism4-70Non-reusable parts

Power Steering System
-Steering Drive and Control Mechanism4-71Replacement1. Precaution (refer to the steering system precaution)
2. Confirm that the wheel stays at a straight line running status.
3. Unfix the storage battery cathode terminal.
4. Remove the airbag assembly.
Remove the two screws on both sides, and pull out the cable connector.
Note: When removing the airbag assembly, never pull the airbag cables.
Caution: When put down the airbag assembly, make sure its top surface stays upward.
Never disassemble the airbag assembly.Using
Socket5. Remove the steering wheel assembly.
(1)Unfix the connector.
(2)Remove the set bolts of the steering wheel.
(3)Make a fit mark on the steering wheel assembly and main shaft assembly.
(4)Remove the steering wheel with special tool.
6. Remove the top shells and bottoms shell of the steering column shield.
(1)Remove the three screws.
(2)Remove the top part and bottom part of the steering column
shield.
7. Remove clock spring.
8. Remove the left combination switch assembly.
Separate the connector and remove the left combination switch
assembly.
9. Remove the right combination switch assembly.
Separate the connector and remove the right combination switch
assembly.
10. Remove the splined tube cover.
11. Detach No. 2 steering countershaft(see right figure)
(1) Make a mark on the fit between slide splined tube and countershaft. (2) Loosen bolts A and B.
12. Remove the steering column pipe assembly.
(1) Remove the cable connector on the steering column pipe assembly. (2) Remove the 3 bolts and steering column assembly.Installation mark

Power Steering System-Steering Drive and Control Mechanism4-7213. Remove the No.2 steering countershaft assembly.
(1) Make a mark on the fit between main shaft and countershaft.
(2) Remove bolt and countershaft.
14. Remove the ignition switch bracket.
(1) Use the punch pin to make a mark on the 2 conical head bolt.
(2) Drill the 2 conical head bolts with the diameter of 3-4mm drill
bit.
(3) Remove the bolts and bracket for the ignition switch with the
thread die.
15. Remove fixing panel on the steering column.
16.Remove the ignition switch lock core assembly.
(1) Turn the ignition switch to "ACC" position.
(2) press the stop pin and pull the lock core out.
17. After checking or replacing the steering column pipe assembly, install all parts in a reverse order.
Note:
(1) After installing the ignition switch lock core, check the operation of the steering locking function: when
pulling out the key, the steering device is locked; when the key is inserted and turned to ACC position, the
steering device is unlocked.
(2) Tighten the 3 bolts.
(3) Make sure all cables are connected reliably.
(4) After adjusting the combination switch as well as the top shell and bottom shell of the steering pipe shield,
fasten the three screws connecting the combination switch and the steering column assembly.
(5) Tighten the set bolt between the universal joint fork and the steering gear assembly with a torque of
22~39N.m.
(6) Install dust cover and its press plate.
(7) When installing the steering wheel assembly, align the steering wheel assembly and the fit mark of the
steering main shaft assembly. Tighten the special quincunx bolt with a torque of 33~59N.m.
(8) Check the airbag. It is not allowed to use a airbag part removed from another vehicle.
(9) Check the SRS warning lamp.Thread die Installation mark

Power Steering System-Steering Pipeline Component4-73I. Onboard Check1. Check the transmission strap.
Check the transmission strap whether it is worn out. If necessary, replace a new transmission strap.
Tips: Crack at the edge of the strap teeth is acceptable. If the strap teeth fall, replace a new strap.
2. Discharge the air in the power steering system.
(1)Check the liquid level.
(2)Lift the front part of the vehicle with a jack in a safety manner.
(3)Rotate the steering wheel.
After the motor is shut down, rotate the steering wheel to the left/right limit position lightly. Repeat such
operation several times.
(4)Loosen the jack, and put down the vehicle.
(5)Start the motor, and make it run idly for several minutes.
(6)Rotate the steering wheel to one side limit position for 2-3 seconds, and then rotate it to the other side limit
position for 2-3 seconds. Repeat such operations several times.Section 3 Steering Pipeline ComponentComponent ViewPower steering high pressure
pipe
Return line (connecting fluld tank)
Power steering pump with bracketReturn line(connecting steering gear)Drive beltN.
m : specified torque

Power Steering System-
Steering Pipeline Component4-74 (7)Shut down the motor, and check whether there is any foam or
emulsification in the oil storage. If so, discharge the air
repeatedly.
(8)Check the level height, and check whether there is any
leakage.
2. Check the level height.
(1)Park the vehicle on the horizontal road.
(2)When the motor stops running, check the level height in the oil
tank. If necessary, add some more ATF DEXRONII steering
liquid.Replacement1. Discharge the steering liquid in the power steering system.
2. Remove the power steering high & low pressure oil pipes.
3. Loosen the connector screws of the high & low pressure oil pipes on the steering gear assembly, and loosen the
oil pipe clip.
4. Loosen the drive belt.
5. Remove the power steering pump strap support assembly from the motor. Remove the 3 coupling bolts between
the power steering pump strap support assembly and the motor.
6. Install the power steering pump strap support assembly.
Fasten the steering pump strap support assembly on the motor, and tighten the M10 bolt with a torque of 45-
79N.m and M8 bolt with a torque of 16-26N.m.
7. Install the drive belt, and make sure the position is correct.
8. Install the high & lower pressure oil pipes of the power steering gear assembly.
(1) Connect the connector screw of the high and low pressure oil pipe to the steering gauge with a torque of
19-33N.m.
(2) Fasten the low pressure oil pipe on the body front baffle plate with clip.
(3) Connect the connector screw of the high pressure oil pipe to the power steering pump with a torque of
19-33N.m.
(4) Connect the connector screw of the low pressure oil pipe to the oil tank with a torque of 19-33N.
m.
9. Discharge all air in the power steering pipe system, and check the pipe system whether there is any leakage.
10. Check the oil reservoir inner fluid level Tips: The level shall stay between the lowest level and the highest level.
(3) Check whether there is any foam or emulsification. If so, discharge the power steering liquid.NormalAbnormal

Power Steering System-Power Steering Gear4-75Component ViewSection 4 Power Steering GearFront suspension crossmenber assembly125-15225-32
*28-35125-15227-3927-39
* :Special toolspecified torqueN.
m :PinGear rack power steering device
Pin

Steering rack end sub-assembly
Steering rack end sub-assembly
Left ball extension shaft Left ball extension shaftComponent ViewPower Steering System-Power Steering Gear4-76Lock nut
Steering rack # 1 dust shield
Clip
Hoop
O-ring Steering hydraulic
oil pipe
O-ring
Hoop
Clip O-ring
Steering rack # 2 dust shield
Non-reusable parts
Power steering oil
Special toolLock nut
Specified torque