2008 GEELY MK torque

Chapter 13 Rear BumperI. Component ViewRight trunk trim board
Rear shelf lower trim panel
Spare tire board
Rear bumper support installation nut
Torque nut: 6 N¡¤mRear bumper Left mud guard Left trunk trim boardInterior & Exterior Trim and Accessory -Rear Bumper6-35II. Disassembly and assembly of the rear bumper Notes:
Installation is basically the reverse of removal and different operation(s) in the process of installation, if any,
will be pointed out specifically.
1. Remove the spare tire cover assembly.
2. Remove the lower trim board of the rear separator.
3. Remove the ornamental blanket at the left side of the luggage compartment.
a. Remove six snaps.

Interior & Exterior Trim and Accessory -Rear Bumper6-36 b. Remove the ornamental blanket at the left side of the luggage
compartment.
4. Remove the ornamental blanket at the right side of the luggage
compartment.
a. Remove six snaps.
b. Remove the ornamental blanket at the right side of the luggage
compartment.
5. Remove the rear bumper.
a. Remove four nuts;
b. Remove two screws and four clips;
c. Remove 8 snaps and the bumper.
6. Mount the rear bumper.
Installation is basically the reverse of removal.
(Notes: Mount the rear bumper with two screws, 4 clips and 4
nuts; Torque: 5.5N.m, for the nut)Snap Rear bumper
Snap

Interior & Exterior Trim and Accessory -Outside Rearview Mirror6-37Chapter 14 Outside Rearview MirrorThe outside rearview mirrors are mounted on the left and right doors. With specially designed rubber sheath, the
rearview mirrors are seamlessly and smoothly joined to the body of vehicle. Meanwhile, they block neither upward
nor backward turn of rearview mirrors upon knocking. Such installation also plays an important role in decreasing
the air resistance coefficient of the whole vehicle.
The mirror glasses are fixed to the supporting plates with double-side adhesive tape. The supporting plates are
connected to the shell of rearview mirrors with ball hinge in order to make sure no glass will scatter that causes
secondary injury, as well as replacing the damaged glasses easily. When the glasses are damaged, the supporting
plates can be taken out of the ball-head mount with tools, and then pressed into the mount again after replacing
the glasses. The turning force of rearview mirror is designed as 30N, which enables easy turn and less hurt/damage
in case human or object knocks the mirror. In addition, the rearview mirrors are equipped with electric adjustment
and heat defrosting.
Notes
When turning over the rearview mirror, please don't put your finger between the exterior rearview mirror and
the hinge in order to avoid extrusion injury!Replacement of Rearview MirrorRemoval procedures
1. Remove the cathode lead wire off the storage battery;
2. Remove the corner decoration of door;
3. Disconnect the plug of electric-driven exterior rearview mirror;
4. Remove the 3 screws;
5. Remove the electric-driven exterior rearview mirror
Installation procedures
1. Mount the rearview mirrors onto the doors
2. Fasten the screws from the lower-left side clockwise
Fastening
Fasten the screws of exterior rearview mirrors with the torque
of 8.0N.m
3. Connect the plug of electric-driven exterior rearview mirrors;
4. Install the corner decoration of door

II. Supplemental Specifications on Tightening TorqueFor those fastening pieces either not specified in the "Body" part or not stated in other assemblies, the following
specifications shall apply.
Thread Dia. Thread Pitch Tightening Torque
(mm) (mm)Standard Value (N.m) Max. Value(N.m) Min. Value(N.m)
61 9 12 6
8 1.25 23 26 16
8 1 25 28 17
10 1.5 59 75 37
10 1.25 63 79 45
10 1 64 80 46
12 1.75 95 111 73
12 1.5 97 113 75
12 1.25 99 115 78
14 2 160 185 122
14 1.5 180 205 146
16 2 215 245 182
16 1.5 240 270 199
18 2.5 268 298 229
18 1.5 316 346 287
20 2.5 430 470 389
20 1.5 440 480 396Body Repair -Service Data For for Body7-37Table 5-2
Supplemental Specifications for Vehicle Body and All Assembly Fastening Piece

1 Engine right insulator x body JQ184C1025(3 pcs)43~58 43~58
2 Brake pedal with bracket assy. x central cross member Q151B0820(1 pcs)22~29 22~29
3Brake pedal with bracket assy. x brake master cylinder
Q32008(4 pcs)22~29 22~29
with vacuum booster assy.
4 Clutch pedal x central cross member Q1840816(1 pcs)/22~29
5 Clutch pedal x clutch master cylinder Q32208(2 pcs)/22~29
6 Accelerator pedal Q32208(2 pcs)22~29 22~29
7 LH/RH front brake pipe component x HECU controller Null13~18 13~18
8 LH/RH rear brake pipe component I x HECU controller Null13~18 13~18
9Brake master cylinder No. 1 and No.2 pipe component
Null13~18 13~18
x HECU controller, brake master cylinder
10Clutch hydraulic hose assy. x master cylinder oil outlet pipe componentNull13~18 13~18
11 Steering column assy. x universal joint assy.Q151B0820TF2(1 pcs)22~29 22~29
12 (LH & RH) front shock absorber component x body37~45 37~45
13 (LH & RH) rear shock absorber component top nut Q341C10(2 pcs) 22~29 22~29
14(LH & RH) front shock absorber piston rod x front
Q330B12(2 pcs)31~38 31~38
suspension bracket sub-assy.
15 (LH & RH) rear seat belt assy. x body7/16" bolt ( )39~53 39~53
16 (LH & RH) front seat belt assy. x body7/16" bolt( )39~53 39~53
17 (LH & RH) front buckle assy. x body7/16" bolt( )39~53 39~53
18 RR seat belt buckle and lap belt assy. x body7/16" bolt( )39~53 39~53
19 LR buckle assy. x body7/16" bolt( )39~53 39~53
20 Rear axle assy. x bodyJQ14012110TF2(2 pcs)73~103 73~103
21 (LH & RH) rear shock absorber x rear axle JQ320B12(2 pcs)47~56 47~56
22LH & RH brake pipe component III x LH & RH rear
Null13~18 13~18
drum brake with wheel hub assy.
23LH & RH rear brake hose x LH & RH rear brake pipe component IIINull13~18 13~18
24 LH/RH rear drum brake with wheel hub assy. x rear axleMounting nut (8pcs)60~72 60~72
25LH/RH rear brake pipe component I x LH/RH rear brake pipe component IINull13~18 13~18Appendix: Torque Table of the Fasteners for Important AssemblyTorque N.m
No.
JL7132HU
JL7152HUJL7132U
JL7152U
JL7162UAppendix-Torque Table of the Fasteners for Important AssemblyIArea Fastener
front suspension
support sub-assy.
Mounting nut (6 pcs)

26LH/RH rear brake pipe component II x rear brake hose assy.Null13~18 13~18
27 front suspension cross member (front part) x bodyJQ1401280TF2(2 pcs)94~110 94~110
28 Front suspension cross member (rear part) x bodyJQ1401455TF2(2 pcs)110~130 110~130
29 Engine right mount x right insulator JQ319B10(1 pcs)49~60 49~60
30 Engine left mount x left insulator JQ184C1030(2 pcs)43~58 43~58
31 Engine left LH x bodyJQ184B12140(1 pcs)94~110 94~110
32 Engine x automatic transmissionJQ140BD1255TF2(2 pcs)/ 55~70
33 Engine x automatic transmissionJQ140BD1260TF2(1 pcs)/ 55~70
34 Engine x automatic transmissionJQ140C1040TF2(1 pcs)/ 43~58
35 Engine x automatic transmission JQ140C1020(3 pcs) /43~58
36 Engine x automatic transmissionJQ140BD1255TF2(2 pcs)55~70 /
37 Engine x automatic transmissionJQ140BD1045TF2(1 pcs)43~58 /
38 Engine x automatic transmissionJQ140C1040TF2(1 pcs)43~58 /
39 Engine x automatic transmission JQ140C0820(3 pcs)22~29 /
40 Starter x transmissionJQ146C1040TF2(2 pcs)30~60 30~60
41 Engine left bracket x transmission JQ184C1030(3 pcs)43~58 43~58
42 Engine rear bracket x engine JQ184C1025(2 pcs)43~58 43~58
43 Engine rear bracket x engine JQ184C1020(1 pcs)43~58 43~58
44 Compressor bracket x engine JQ146C1035(1 pcs)43~58 43~58
45 Compressor bracket x engine JQ146C1030(3 pcs)43~58 43~58
46Power steering pump with bracket assy. (without reservoir) x engineQ1420825(3 pcs)22~29 22~29
47Power steering pump with bracket assy. (without reservoir) x engineQ14201030(1 pcs)43~58 43~58
48 Oil pump adjustment bracket x engine JQ146C1030(2 pcs)43~58 43~58
49Oil pump adjustment bracket x power steering pump
JQ146C1030(1 pcs)43~58 43~58
with bracket assy. (without reservoir)
50Oil pump mounting bracket x power steering pump with
JQ142C1085(2 pcs)43~58 43~58
bracket assy. (without reservoir)
51Oil pump mounting bracket x power steering pump with
Q40110(1 pcs)43~58 43~58
bracket assy. (without reservoir)
52Oil pump mounting bracket x power steering pump with
Q361C10(1 pcs)43~58 43~58
bracket assy. (without reservoir)
53 Rear insulator x front suspension cross member JQ184C1060(1 pcs)43~65 43~65Appendix-Torque Table of the Fasteners for Important AssemblyIITorque N.m
No.
JL7132HU
JL7152HUJL7132U
JL7152U
JL7162U Area FastenerAppendix: Torque Table of the Fasteners for Important Assembly

54 Rear insulator x front suspension cross member JQ319C10(2 pcs)43~65 43~65
55 Front stabilizer bar x front suspension cross member Q1400825(4 pcs)22~29 22~29
56Power steering gear with tie rod assy. x front suspension cross memberJQ184B1265(2 pcs)125~152 125~152
57High/low pressure oil pipe assy. x power steering gear with tie rod assy.Null25~32 25~32
58LH & RH lower suspension swing arm x front susJQ1401280TF2(2 pcs)125~152 125~152
pension cross member rear
59LH & RH lower suspension swing arm x front sus
JQ320B12(2pcs)125~152 125~152
pension cross member rear
60LH & RH lower suspension swing arm x front sJQ1401280TF2(2 pcs)83-103 83-103
uspension cross member front
61Front stabilizer bar x LH & RH lower suspension swing arm assy.JQ33808(2 pcs)22~29 22~29
62(LH & RH) front brake hose x (LH & RH) front disk13~18 13~18
brake with steering knuckle assy.
63 Engine rear insulator x rear bracket Q184C10105(1 pcs)61~74 61~74
64High pressure oil pipe assy. x power steering pump with bracket assy.Union bolt51~63 51~63
65(LH & RH) lower swing arm ball joint x (LH & RH) disk
JQ38312(2 pcs)83~103 83~103
brake with steering knuckle assy.
66LH & RH brake with steering knuckle assy. x power
Q383B10(2 pcs)30~40 30~40
steering gear assy. with tie rod assy.
67(LH & RH) front disk brake with steering knuckle assy.
JQ1841450TF2(4 pcs)125~152 125~152
x (LH & RH) front shock absorber
68(LH & RH) front disk brake with steering knuckle assy.
JQ320C14(4 pcs)125~152 125~152
x (LH & RH) front shock absorber
69 LH/RH constant velocity drive shaft assy. Set nut190~230 190~230
70(LH & RH) front brake hose x (LH & RH) front brake pipeNull13~18 13~18
71Front suspension reinforcement member x front
JQ1401020(4 pcs)43~58 43~58
suspension cross member, body
72 Oil tank component x bodyJQ146Db0835A(4 pcs)22~29 22~29
733-way catalytic converter assy. x engine exhaust manifoldJQ189C1058TF2E(4 pcs)40~60 40~60
74 Intermediate muffler x 3-way catalytic converter assy. JQ1461035(2 pcs)40~60 40~60
75 Intermediate muffler x 3-way catalytic converter assy. JQ32010(2 pcs)40~60 40~60
76 Primary muffler x intermediate muffler JQ1461035(2 pcs)40~60 40~60Appendix-
Torque Table of the Fasteners for Important AssemblyIIITorque N.m
No.
JL7132HU
JL7152HUJL7132U
JL7152U
JL7162U Area FastenerAppendix: Torque Table of the Fasteners for Important Assemblybrake hose union
bolt (2 pcs)

Torque N.m
No.
JL7132HU
JL7152HUJL7132U
JL7152U
JL7162U Area FastenerAppendix: Torque Table of the Fasteners for Important Assembly77 Primary muffler x intermediate muffler JQ32010(2 pcs)40~60 40~60
78 Engine right mount x right insulator JQ184C1040(2 pcs)49~60 49~60
79 Wheel rim x wheel hub Hub nut (16 pcs)88~117 88~117
80 Universal joint x power steering gearQ151B0820TF2(1 pcs)22~29 22~29
81 Steering wheel x steering column assy. Steering wheel nut33~59 33~59Appendix-Torque Table of the Fasteners for Important AssemblyIV