Page 298 of 419
Light--Front fog light joint
Change
Notes:
zAssemble according to the opposite of disassemble. Instructions comes when necessary.
zThe replace procedure are the same on the left and right side.
zReferring to the drawing of front combination light on page 286.
1. Disassemble Radiator cover assembly (reference to page 380)
2. Disassemble left front tyre lining (reference to page 380)
3. Disassemble right front tyre lining (reference to page 380)
4. Disassemble front bumper (reference to page 380)
5. Disassemble left front combination light assembly [67000102]
(a) Disassemble three bolts
(b) Disassemble four joints
(c) Pull combination light ahead
(d) Disassemble two light seat cap and four bulbs.
Adjustments
1. Adjust front combination light focus only
(a) Parking car should accord to the following situations:
zFront combination light around does not be distorted or damaged.
zPark the car on flat road.
zTyre pressure limits to the regular number value
zThe driver is on driving seat and the car is ready to go(gasoline tank in full)
zThe car weaves fore-and-aft for many times.
(b) Inspect front combination light focus
(1) Prepare for thicker white paper
(2) Arise the paper plumb at the distance of 300cm from headlight.
(3) Make sure centerline of the car makes 90 degree angle with paper’s surface as following drawing.
(4) Draw a level line (H line) on the paper which headlight can irradiate.
(5) Draw a plumb line (V line) on the paper to across centerline of the car.
(6) Draw two level lines (V RH and V LH) in the area where two side lights can irradiate.
(7) Draw a level line(connect the middle signal of two low beam headlight) to the area where headlight
can irradiates.
Clues on: H RH and H LH lines are 0.57 lower than level line(H line)of light.
(8) Start the engine.
(9) Turn the front assembled switch to ON.
Pin
287
Page 300 of 419
Light--Front fog light joint
Front fog light
Components
289
Front fog light joint
Left front fog light unit
Bulb
Page 301 of 419
Light--Front fog light joint
Change
Notes:
zAssemble according to the opposite of disassemble.
Instructions comes when necessary.
zThe replace procedure are the same, left and right side.
zReferring to the drawing of front combination light on
page 286
1. Replace front fog light bulb
(a) Disassemble front fog light seal cap
(b) Press front fog light bulb spring
(c) Disassemble the bulb
Adjustments
1. Adjust front fog light optic axis
(a) Tyre pressure limits to regular number values.
(b) Start the engine.
(c) Adjust fog light optic axis by turning the optic axis adjust-
able button on the vertical direction.
290
Page 303 of 419
Light--Rear combination light
Rear combination light (LH)
Components
Left rear combination light Bulb
292
Page 304 of 419
Light--Rear combination light
Change
Notes:
zAssemble according to the opposite of disassemble. Instructions comes when necessary.
zThe replace procedure are the same on the left and right side.
zReferring to the drawing of front combination light on page 286
1. Disassemble left rear combination light assembly [67000108]
(a) Disassemble three bolts and rear combination light.
(b) Disassemble two bulbs
293
Page 305 of 419
Light--Rear fog light
Rear fog light
Components
294
Rear fog light jointLeft rear fog light
Bulb
Page 307 of 419
Light--Number plate light
Number plate light
Change
1. Disassemble key aperture of trunk cover and bracket
2. Disassemble number plate light of trunk cover
3. Disassemble number plate light assemble [68000097]
(a) Disassemble the joints.
(b) Disassemble number plate light using vice screw driver.
Clues on: Before using vice screw driver, its cusp
should enwind adhesive tape.
(c) Disassemble the bulb.
296
Fixing
claw
