2008 FIAT BRAVO ESP

Avoid keeping your hand on
the lever when you are not re-
questing a gear shift or an
Auto/Manual mode change.
4
OPERATING MODE
The gearbox can work in two operating
modes:
❒the first is manual (MANUAL),
where the driver decides directly
when to shift gear;
❒the second fully automatic (AUTO),
where the system decides when to
shift gear. ECOfunction (Economy)
can be used with this mode reducing
fuel consumption. To turn this func-
tion on, press button E-fig. 3located
on the gearbox trim.
The selection of the gear and the oper-
ating mode (MANUAL or AUTO) is
made using the control lever A-fig. 1in
the centre console. The system returns to the manual mode
by returning the lever to the A/Mposi-
tion.
With the car at a standstill and the key re-
moved, the lever may be moved
with/without the brake pedal pressed. The
system does not carry out any action af-
ter the lever has been moved and remains
in the gear memorized before the key was
removed.
IMPORTANT After starting, if there is an
error between the position of the lever and
the gear actually engaged, this will be sig-
nalled, when the brake pedal is released, by
a buzzer and by the letter N flashing in the
display until the inconsistency no longer ex-
ists. CONTROL LEVER
The control lever A, located in the dash-
board, is the floating multistable type, i.e.
it can take up three stable positions and
three unstable positions.
The three stable positions correspond to
neutral (N), reverse (R) and the middle
position between the unstable positions
(+) and (–).
The unstable positions, in other words
those which are abadonned as soon as the
lever is released, are the position re-
questing a higher gear (+), the position re-
questing a lower gear (–) and the position
requesting the automatic operating mode
(A/M).
fig. 3 F0Q0105m
603.83.941 Bravo Dualogic GB 5-05-2008 10:53 Pagina 4

6
Automatic operation
(AUTO - ECO)
The ECOcan only be activated with the
automatic mode engaged.
The ECOfunction is turned on by press-
ing button E-fig. 6located on the trim
next to the gear lever. After this function
has been activated, the display will show
the gear engaged and the words AUTO
and E.
The ECOfunction activates the system
selecting the most suitable gear depend-
ing on the speed of the car, the engine
speed and the intensity with which the ac-
celerator is pressed with fuel economy be-
ing the main objective.
fig. 7 F0S0236m
INFORMATION ON DISPLAY
When the ignition key is turned to MAR,
after around one second, display shows
the gear engaged and the last mode used
(AUTOor MANUAL):
N= neutral;
1= first gear;
2= second gear
3= third gear;
4= fourth gear;
5= fifth gear;
6= sixth gear;
R= reverse.
If the ECOfunction is used the display will
show the letter E(Economy) next the
gear engaged fig. 8-9.
IMPORTANT If the display does not
show the gear engaged after 10 seconds
with the ignition key in MAR, turn the ig-
nition to STOP, wait for the display to
turn off and then repeat the manoeuvre.
If the problem persists, contact the Fiat
Dealership. If necessary (e.g. when overtaking) the sys-
tem changes down a gear or more in or-
der to provide appropriate power and
torque for the acceleration requested by
the driver (this all takes place in automat-
ic mode irrespective of whether or not
the ECOfunction is activated).
603.83.941 Bravo Dualogic GB 5-05-2008 10:53 Pagina 6

8
To engage 2ndgear
❒press the brake pedal;
❒with the lever in (N) or (R) move the
lever to the middle position and then
toward (+)
❒with the lever already in the middle po-
sition, move the lever twice toward (+)
❒release the brake pedal and press the
accelerator pedal.
It is possible to engage 1st or 2nd gear
with the lever in the middle position and
the brake pedal pressed using the lever (+)
located behind the steering wheel (where
present). For departures on a hill with a
medium-steep gradient, it is advisable to
use the handbrake.To engage reverse (R)
❒press the brake pedal (car completely
stationary)
IMPORTANT If the car is moving, the re-
quest is accepted and carried out if the car
speed is less than 3 km/h within 1.5 sec-
onds of the request: if the request is not
implemented, the system will maintain the
gear engaged or if car speed drops below
10 km/h it will put the gearbox in neutral
(N) and the manoeuvre must then be re-
peated.
❒move the lever to (R)
❒release the brake pedal and press the
accelerator pedal. DRIVING OFF IN THE CAR
Driving off in the car, take-off, is permit-
ted in 1
st gear and 2ndgear (recommend-
ed on road surfaces with poor grip) and
reverse (R).
To engage 1
stgear
❒press the brake pedal;
❒with the lever in (N) or (R) move the
lever to the middle position;
❒with the lever already in the middle po-
sition, move the lever toward (+);
❒release the brake pedal and press the
accelerator pedal (pressing the pedal
quickly so that it reaches the end of
travel and turning off the ASR function,
if present, allow a responsive take off).
It is possible to engage 1
stor 2ndgear with
the lever in the middle position and the
brake pedal pressed using the lever (+) lo-
cated behind the steering wheel (where
present).
For departures on a hill with a medium-
steep gradient, it is advisable to use the
handbrake.
603.83.941 Bravo Dualogic GB 5-05-2008 10:53 Pagina 8

10
WARNING LIGHTS
AND MESSAGESREDUCE GEAR CHANGES
The message appears in the display to in-
dicate that the driver is using the gearbox
incorrectly.
Incorrect use (by the driver) could auto-
matically activate a procedure for pro-
tecting the system. DUALOGIC GEARBOX
FAILURE (red)
When the ignition key is
turned to MAR, the warning
light turns on and should go off after a few
seconds.
The warning light on the dial comes on
flashing (together with a message in the
display and a buzzer) to indicate that the
gearbox is faulty.
t
If a fault is present, contact
a Fiat Dealership as soon as
possible to check the sys-
tem.
Contact a Fiat Dealership if
the message remains in the
display.
❒if necessary, with the engine off it is pos-
sible to engage 1stgear or reverse (R)
with the ignition ONand the brake
pressed. In this case, gear shifts must be
made allowing at least 5 minutes to
elapse between one gear shift and the
next to safeguard the operation of the
hydraulic system and the pump in par-
ticular;
❒pressing the accelerator pedal quickly
until it is in the end of travel position
and switchin off the ASR function, if
present, using the button in the dash-
board allows for a responsive take off.
❒during hill starts, accelerate gradually
but fully immediately after releasing the
handbrake or brake pedal to allow the
engine to increase its rpm to a greater
extent and overcome higher gradients
with more torque.
603.83.941 Bravo Dualogic GB 5-05-2008 10:53 Pagina 10