2008 DODGE RAM 2500 POWER WAGON TPMS reset

INSTRUMENTS AND CONTROLS
1 Ð Headlight Switch 6 Ð Passenger Airbag* 11 Ð Cup Holders
2 Ð Air Outlets 7 Ð Glove Box 12 Ð Cigar Lighter
3 Ð Instrument Cluster 8 Ð Power Outlet 13 Ð Electronic Axle Locker and Disconnecting Sway Bar Switch
4 Ð Climate Controls 9 Ð Heated Seat Switch 14 Ð Parking Brake Release Lever
5 Ð Radio 10 Ð TPMS ªLight Loadº Reset Switch* 15 Ð Adjustable Pedal Control Switch*
* If EquippedUNDERSTANDING YOUR INSTRUMENT PANEL 177
4

TPMS ªLight Loadº Reset Switch ± If Equipped
The TPMS ºLight Loadº reset switch allows you to
choose between Light Load vehicle conditions and Max
Load vehicle conditions tire pressures and related TPMS
warning levels. The switch is located in the instrument
panel, below the climate control panel. For additional
information refer to ªTire Pressure Monitoring System
(TPMS) Ð If Equippedº in section 5 of this manual.
25. Transmission Oil Temperature Warning Light
(Automatic Transmissions Only)
This light indicates that there is excessive trans-
mission fluid temperature that might occur
with severe usage such as trailer towing. It may
also occur when operating the vehicle in a high
torque converter slip condition, such as 4-wheel-drive
operation (e.g. snow plowing, off- road operation). If thislight comes on, stop the vehicle and run the engine at idle
or faster, with the transmission in NEUTRAL until the
light goes off.
26. Odometer/Trip Odometer Button
Press this button to toggle between the odometer and the
trip odometer display. Holding the button in resets the
trip odometer reading when in trip mode.
27. Fuel Gauge
Shows level of fuel in tank when ignition switch is in the
ON position.
28. Low Fuel Warning Light
When the fuel level drops to 1/16 tank, the fuel
symbol will light and a single chime will sound.
NOTE:If your vehicle is equipped with an overhead
console module (CMTC), it is possible for DTE to display
ªLO FUELº before the low fuel warning light turns on in
the instrument cluster. This could occur because the low
UNDERSTANDING YOUR INSTRUMENT PANEL 189
4

mMulti Displacement System (MDS) Ð 5.7L Engine
Only................................326
mTire Safety Information...................326
NTire Markings........................326
NTire Identification Number (TIN)..........330
NTire Loading And Tire Pressure...........331
mTires Ð General Information...............335
NTire Pressure.........................335
NTire Inflation Pressures.................336
NRadial-Ply Tires......................338
NCompact Spare Tire Ð If Equipped.........339
NLimited Use Spare Ð If Equipped.........339
NTire Spinning........................340NTread Wear Indicators..................341
NLife Of Tire.........................341
NReplacement Tires.....................342
NAlignment And Balance.................343
mSupplemental Tire Pressure Information Ð
If Equipped...........................344
mTire Chains...........................344
mSnow Tires...........................345
mTire Rotation Recommendations............346
mTire Pressure Monitor System (TPMS) Ð
If Equipped...........................347
NTire Pressure Monitor System (TPMS) ªLight
Loadº Reset Switch Description ±
If Equipped.........................350
STARTING AND OPERATING 255
5

TIRE PRESSURE MONITOR SYSTEM (TPMS) Ð IF
EQUIPPED
The Tire Pressure Monitoring System (TPMS) will warn
the driver of a low tire pressure based on the vehicle
recommended cold tire inflation placard pressure. The
placard pressure is defined on the Tire and Loading
Information label. The Tire and Loading Information
label is located on the drivers side B-pillar. Vehicles
equipped to be operated in either the ªmax load inflation
pressureº condition described on the Tire and Loading
Information label or the alternative ªlight load inflation
pressureº condition described on the Supplemental Tire
Pressure Information label, may also be equipped with a
reset switch to choose the appropriate TPMS low pres-
sure warning threshold levels based upon the vehicle
load condition. The Supplemental Tire Pressure Informa-
tion label is located on the rear face of the driver door.
Operation of the ªLight Loadº reset switch is described
later in this manual section.The tire pressure will vary with temperature by approxi-
mately 1 psi (6.9 kPa) for every 12ÉF (6.5ÉC). This means
that when the outside temperature decreases, the tire
pressure will decrease. Tire pressure should always be set
based on cold inflation tire pressure. This is defined as
the tire pressure after a vehicle has not been driven for
more than 3 hours, or driven less than 1 mile (1km/h)
after a 3 hour period.Refer to the ªTires ± General
Informationº in this section for information on how to
properly inflate the vehicle's tires.The tire pressure will
also increase as the vehicle is driven - this is normal and
there should be no adjustment for this increased pres-
sure.
The TPM System will warn the driver of a low tire
pressure if the tire pressure falls below the low pressure
warning threshold for any reason, including low tem-
perature effects, or natural pressure loss through the tire.
STARTING AND OPERATING 347
5

Tire Pressure Monitor System (TPMS) ªLight
Loadº Reset Switch Description ± If Equipped
WARNING!
Never operate your vehicle with the TPMS and tire
pressures set to the Light Load Inflation Pressure
settings if carrying more than two occupants ( 150 lbs
each) plus 200 pounds of cargo. The vehicle ªLight
Load Definitionº is found in the Supplemental Tire
Pressure Information Label which is located on the
rear face of the driver door. Failure to do so may
cause you to lose control resulting in an accident,
causing serious or fatal injury.The Tire Pressure Monitor (TPM) system ªLight Loadº
reset switch will allow the driver to switch between the
max load inflation pressure (cold) low pressure warning
threshold and the light load inflation pressure (cold) low
pressure warning threshold depending on the vehicle's
load condition. The Tire and Loading Information label
defines the recommended front and rear cold tire infla-
tion pressures for the vehicle when operating in the Max
Load condition. A Supplemental Tire Pressure Informa-
tion label is also available defining Light Load tire
inflation pressures when operating in the Light Load
condition. When the ªLight Loadº reset switch LED is
ON, the Tire Pressure Monitoring (TPM) system is using
the light load inflation pressure (cold) low inflation
warning thresholds and will warn the driver if one or
more of the tire pressures are 25% or more below the
vehicle's defined light load inflation pressures.
350 STARTING AND OPERATING

²The TPMS system will always reset to the max load
inflation pressure (cold) low pressure warning thresh-
old condition when the system experiences a loss of
electrical power. For example, by momentarily discon-
necting the battery or IOD fuse.To switch from the max load inflation pressure (cold) low
pressure warning threshold to the light load inflation
pressure (cold) low pressure warning threshold, the
driver must first lower all four road tire pressures to the
Light Load Inflation Pressure values as listed on the
Supplemental Tire Pressure Information label. The
Supplemental Tire Pressure Information label is located
on the rear face of the driver door. Use an accurate tire
gauge to check the tire pressures when lowering all four
tire pressures. Next proceed to turning the ignition on to
the Run position. This may cause the TPMS low pressure
warning telltale lamp located in the Instrument Cluster to
turn ON and a chime to sound since the tire pressures
have been lowered below the max load inflation pressure
(cold) pressures. After all four tire pressures have been
lowered to the Light Load inflation pressures, press the
ªLight Loadº reset switch. If the ªLight Loadº switch
amber colored LED turns ON, the TPM system low
pressure telltale lamp will illuminate at a tire pressure
Example Supplemental Tire Pressure Label
352 STARTING AND OPERATING

WARNING!
It is the driver 's responsibility to change to the max
load inflation pressure (cold) low pressure warning
threshold condition when not driving in the light
load condition as defined as two occupants ( 150 lbs
each) plus 200 pounds of cargo. The vehicle ªLight
Load Definitionº is found in the Supplemental Tire
Pressure Information Label located on the rear face of
the driver door. Failure to do so may cause you to lose
control resulting in an accident, causing serious or
fatal injury.To switch back to the max load inflation pressure (cold)
low pressure warning threshold, press the ªLight Loadº
reset switch. It is not necessary to first fill the tires to the
max load inflation pressure (cold) values to switch the
TPMS system to the max load inflation pressure (cold)
low pressure warning threshold. If after pressing the
ªLight Loadº reset switch and tire pressures are below
the max load inflation pressure (cold) low pressure
warning thresholds, the TPMS low pressure warning
telltale lamp located in the Instrument Cluster will turn
ON and a chime will sound. The tire pressures are now
required to be inflated to the max load inflation pressure
(cold) values described on the Tire and Loading Informa-
tion label. The Tire and Loading Information label is
located on the drivers side B-pillar. If the ªLight Loadº
reset switch LED turns OFF the TPMS has been reset and
the low pressure telltale lamp will illuminate at tire
pressures 25% or more below the max load inflation
pressure (cold) values.
354 STARTING AND OPERATING

Tire Pressure Monitor System Components
The Tire Pressure Monitor System (TPMS) uses wireless
technology with wheel rim mounted electronic sensors to
monitor tire pressure levels. Sensors, mounted to each
wheel as part of the valve stem, transmit tire pressure
readings to the Receiver Module.
NOTE:It is particularly important, for you to check the
tire pressure in all of your tires regularly and to maintain
the proper pressure.
The Tire Pressure Monitoring System (TPMS) consists of
the following components:
²Receiver Module
²4 Wheel Sensors
²2 Trigger Modules (mounted in the front wheel-wells)
²ªLight Loadº Reset Switch (located in the instrument
panel)
²Tire Pressure Monitoring Telltale Lamp
Tire Pressure Monitoring Low Pressure Warnings
The Tire Pressure Monitoring Telltale Lamp will
illuminate in the instrument cluster, and an au-
dible chime will be activated when one or more of
the four active road tire pressures are low. Should this
occur, you should stop as soon as possible, check the
inflation pressure of each tire on your vehicle and inflate
each tire to the vehicle's recommended cold placard
pressure value. The system will automatically update
and the Tire Pressure Monitoring Lamp will extinguish
once the updated tire pressures have been received. The
vehicle may need to be driven for up to 10 minutes above
15 mph (25 km/h) to receive this information.
Check TPMS Warnings
The Tire Pressure Monitoring Telltale Warning Light
located in the Instrument Cluster will flash on and off for
75 seconds and will remain on solid when a system fault
is detected. The system fault will also sound a chime. If
STARTING AND OPERATING 355
5