2008 DODGE CALIBER 4WD

▫Front Suspension Ball Joints..............332
▫Body Lubrication.....................333
▫Windshield Wiper Blades................333
▫Windshield Washer Fluid Reservoir........334
▫Exhaust System......................334
▫Cooling System.......................335
▫Hoses And Vacuum/Vapor Harnesses.......340
▫Fuel System Connections................340
▫Brake System........................341
▫Automatic Transaxle (CVT)..............343
▫Manual Transaxle.....................344
▫Rear Drive Assembly (RDA) – AWD/4WD
Models Only........................345▫Power Transfer Unit (PTU) – AWD/4WD
Models Only........................345
▫Appearance Care And Protection From
Corrosion...........................346

Fuses/Integrated Power Module (IPM).......351

Vehicle Storage........................355

Replacement Bulbs......................355

Bulb Replacement......................355
▫Headlights/Front Parking/Front Turn Signal . . 355
▫Fog Lights..........................356
▫Tail Lights, Rear Turn Signals And Backup
Lights — Replacement..................356
▫License Lights........................358
▫Center High-Mounted Stoplight...........359
316 MAINTAINING YOUR VEHICLE

Frequency Of Fluid Change
Under normal operating conditions, the fluid installed at
the factory will give satisfactory lubrication for the life of
the vehicle. Fluid changes are not necessary lubricant has
become contaminated with water.
NOTE:If contaminated with water, the fluid should be
changed immediately.
Rear Drive Assembly (RDA) – AWD/4WD Models
Only
Lubricant Selection
Use only the manufacturer’s recommended fluid. Refer
to “Fluids, Lubricants and Genuine Parts” under Section
8.
Fluid Level Check
Visually inspect the unit at each oil change for leakage. If
leakage is detected, check the fluid level by removing thefill plug. The fluid level should be maintained between the
bottom of the fill hole to 1/8 in (4 mm) below the fill hole.
Add fluid, if necessary, to maintain the proper level.
Frequency Of Fluid Change
Refer to the “Maintenance Schedule” under Section 8.
Power Transfer Unit (PTU) – AWD/4WD Models
Only
Lubricant Selection
Use only the manufacturer’s recommended fluid. Refer
to “Fluids, Lubricants, and Genuine Parts” under Section
8.
Fluid Level Check
Visually inspected the unit at each oil change for leakage.
If leakage is detected, Check the fluid level by removing
the fill plug. The fluid level should be maintained be-
tween the bottom of the fill hole to 1/8 in (4 mm) below
the fill hole.
MAINTAINING YOUR VEHICLE 345
7

Cleaning Plastic Instrument Cluster Lenses
The lenses in front of the instruments in this vehicle are
molded in clear plastic. When cleaning the lenses, care
must be taken to avoid scratching the plastic.
1. Clean with a wet, soft rag. A mild soap solution may
be used, but do not use high alcohol content or abrasive
cleaners. If soap is used, wipe clean with a clean, damp
rag.
2. Dry with a soft cloth.
Seat Belt Maintenance
Do not bleach, dye or clean the seat belts with chemical
solvents or abrasive cleaners. This will weaken the fabric.
Sun damage can also weaken the fabric.
If the seat belts need cleaning, use a mild soap solution or
lukewarm water. Do not remove the seat belts from the
car to wash them.Replace the seat belts if they appear frayed or worn or if
the buckles do not work properly.
Dry with a soft cloth.
FUSES/INTEGRATED POWER MODULE (IPM)
An Integrated Power Module (IPM) is located in the
engine compartment near the air cleaner assembly. This
center contains cartridge fuses and mini-fuses. A label
that identifies each component may be printed on the
inside of the cover. Refer to “Engine Compartment” in
this section of the Owner’s Manual for the underhood
location of the IPM.
Cavity Cartridge
FuseMini-
FuseDescription
1 Empty Empty
2 15 Amp
Lt BlueAWD/4WD ECU
Feed
MAINTAINING YOUR VEHICLE 351
7