2008 Citroen C6 DAG lock
[x] Cancel search: lockPage 94 of 216
97
III
A
BC
D
R E A R S E A T S
Seat cushion folded.
Stow the head restraints.
Press the control A located at the end of the backrest and fully tilt for-wards.
The benchseat backrest can be folded in two sections. When you reposition the backrest, make sure that it locks in place.
Your vehicle's boot can be kept isolated from the passenger com-partment.
To lock the access to the boot:1. Place the benchseat in its correct position.The red warning lamp on control A should no longer be visible.
2. Insert the ignition key in the lock.3. Lock it.
Before moving the seats
So as to avoid damaging the seat belts by jamming them, take care to keep them to the sides of the backrest.
LOCKING/UNLOCKING OF THE ACCESS INTO THE BOOT VIA THE REAR BENCHSEATREAR CENTRAL SEAT BELT
For easier opening of the seat belt cover D , y o u s h o u l d fi r s t r a i s e t h e central head restraint.
I n s e r t t h e fi r s t f a s t e n i n g C into the front left hand(black) buckle, then insert the second fastening B into the front right hand buckle.
Page 103 of 216
106
III221
2
2
I N T E R I O R L I G H T I N G
Front
INTERIOR LAMPS
1. Interior lamps
A press on button 1 of the front interior lamp, switches the interior lamps on or off.
Switching on and off is progressive after an action on the remote con-trol, but immediate after a press on button 1.
Rear
2. Spotlamps
A press on one of the buttons 2switches the corresponding spot-lamp on or off.
These only work when the ignition is switched on.
Automatic lighting of the interior lampsThey come on when you remove the ignition key, unlock the vehicle or open a door.
They go out progressively when the doors are closed, the vehicle locked or the ignition switched on.
Deactivation/Activation of automatic lighting
A long press on button 1, deacti-vates the operaton of the inerior lamps. To reactivate them, press on the same button.
Changing bulbsTo change a front interior lamp bulb: Detach the transparent screen. Use a bulb W 5 W.
To change a rear interior lamp bulb: Detach the two surrounds of the transparent screen and pull it away. Use a bulb W 5 W.
Page 117 of 216
120
IV
NOTES ON RADIO RECEPTION
Your radio will be subject to certain phenomena that are not encoun-tered by domestic systems.
The reception of AM and FM sig-nals may suffer from interference, which is caused by the nature and propagation of the signals and d o e s n o t r e fl e c t o n t h e q u a l i t y o f your radio installation.
In AM, the reception may be affected when passing under power lines or bridges, or when travelling through tunnels.
In FM mode, the reception may be affected by the distance from the s t a t i o n t r a n s m i t t e r , t h e r e fl e c t i n g o f signals off obstacles (mountains, hills, tower blocks) and radio blacks-pots (no coverage from the station transmitter).
SELECTION OF RADIO SOURCE
Press button D to select the source.
You can also do this by means of control 5 at the steering wheel.
R A D I O S O U R C E
SELECTION OF FREQUENCIES AND MEMORY BANKS
Press button R successively to go through the memory banks FM1, FM2 and FM3, for the FM wave-band, and the memory banks MW/LW, for the AM waveband.
MANUAL SEARCH
Manual search is via buttons Jor M.
By keeping button J or M pressed, you will be able to scroll through the waveband. Scrolling will stop as soon as you release the button. The radio will remain tuned to the frequency that is displayed.
TUNING SENSITIVITY
Automatic searches can be carried out according to two levels of sen-sitivity:To capture the most powerful transmitters, choose the local search mode "LO" (default option).
To capture the weakest or most distant transmitters, choose the sensitive search mode "DX".
Page 129 of 216
132
IV
QUESTIONANSWERSOLUTION
Tr a f f i c A n n o u n c e m e n t s ( TA ) i s d i s p l aye d. I d o n o t r e c e i ve a n y t r a f fi c i n f o r m a t i o n o r p u b l i c announcements.
T h e p a r t i c u l a r r a d i o s t a t i o n i s n o t i n t h e r e g i o n a l t r a f fi c information network.Change to a radio station that does broadcast t r a f fi c i n f o r m a t i o n .
The reception quality of the radio station being listened to gradually deteriorates.
The vehicle is too distant from the transmitter, or no transmitter is present in the geographical area you a re passing through.
Activate the RDS function to allow the system to check whether a more power ful transmitter is to be found in the geographical area.
The environment (hills, high buildings, tunnels, under-ground car parks, etc.) is blocking reception, even in RDS mode.
This phenomenon is normal and does not imply anything wrong with the radio.
The aerial is absent or has been damaged (for example after going through a car wash or in an underground car park).Have the aerial checked by a CITROËN dealer.
When the engine is not running, the radio stops after a few minutes.
When the engine is switched off, the working time for the radio depends on the battery charge. The interruption is normal.: the radio goes into economy mode, cutting of f in order to save the vehicle’s battery.
You have to start the engine so as to increase the battery charge.
The message "the audio system is overheating" appears on the screen.
In order to protect the audio equipment in excessive ambient temperatures, the radio goes into an automatic thermic protection mode which results in a reduction in sound volume or stopping of the CD player.
Switch off the audio system for a few minutes in order to allow the system to cool down.
F R E Q U E N T L Y - A S K E D Q U E S T I O N S
Page 135 of 216
138
V
A
D
C
B
BATTERY LOCATION AND ACCESS
The battery is located in the boot under the left hand wing trim. To access the battery, rotate the pin o n t h e fl a p b y a 1 / 4 .
CHANGING THE BATTERY (Contact a CITROËN dealer).1. Release the two pins on each side at the back of the boot, and remove t h e b o o t fl o o r .2. O n e a c h s i d e t r i m , r e l e a s e t h e t w o fi x i n g p i n s A.3. Undo the two screws B on each side and remove the sill embellisher.4. On the side trim close to the battery, release the pin D.5. Separate the side trim close to the battery, pulling hard to free the other fi x i n g p o i n t s .6. Unclip the boot lamp C.7. Disconnect both battery terminals.8. Release the battery from its support.9. Remove the battery.
Before changing or repairing the battery, open all four windows.
If you have to unlock your vehicle with the key because of a problem with the battery, any opening/clo sing of a door with the window closed may seriously dama ge the glass to the point of breaking it.
1 2 V B A T T E R Y
Page 140 of 216
143
V
T A B L E O F F U S E S
Ref.RatingFunction
F 1– –
F 2– –
F 35 AAirbags
F 410 A B r a k i n g s y s t e m – A c t i v e b o n n e t – C r u i s e c o n t o l / s p e e d l i m i t e r – P h o t o c h r o m i c r e a r v i e w m i r r o r – D i a g n o s t i c s o c k e t – Multifunction screen inclination motor B r a k i n g s y s t e m – A c t i v e b o n n e t – C r u i s e c o n t o l / s p e e d l i m i t e r – P h o t o c h r o m i c r e a r v i e w m i r r o r – D i a g n o s t i c s o c k e t – B r a k i n g s y s t e m – A c t i v e b o n n e t – C r u i s e c o n t o l / s p e e d l i m i t e r – P h o t o c h r o m i c r e a r v i e w m i r r o r – D i a g n o s t i c s o c k e t –
F 530 A F r o n t w i n d o w – S u n r o o f
F 630 ARear window
F 75 A S u n v i s o r l i g h t i n g – G l o v e b o x l i g h t i n g – I n t e r i o r l a m p s – R e a r c i g a r - l i g h t e r
F 820 A C o n t r o l s a t t h e s t e e r i n g w h e e l – D i s p l a y – O p e n i n g o f w i n d o w s ( M i c r o - d e s c e n t ) – A l a r m – R a d i o
F 930 AFront cigar-lighter
F 1015 A B o o t r e l a y u n i t – T r a i l e r r e l a y u n i t
F 1115 ASteering lock
F 1215 A D r i v e r ’ s a n d f r o n t p a s s e n g e r ’ s s e a t b e l t w a r n i n g l a m p – O p e n i n g o f w i n d o w s ( M i c r o - d e s c e n t ) – E l e c t r i c s e a t s – P a r k i n g a s s i s t a n c e – A u d i o s y s t e m J B L
F 135 A A c t i v e b o n n e t – R a i n a n d b r i g h t n e s s s e n s o r – W i n d s c r e e n w i p e r – E n g i n e r e l a y u n i t s u p p l y
F 1415 A L a n e D e p a r t u r e W a r n i n g S y s t e m – A i r c o n d i t i o n i n g – I n s t r u m e n t p a n e l – H e a d - u p d i s p l a y – A i r b a g s – B l u e t o o t h® (Hands-® f r e e k i t ) – B H I r e l a y L a n e D e p a r t u r e W a r n i n g S y s t e m – A i r c o n d i t i o n i n g – I n s t r u m e n t p a n e l – H e a d - u p d i s p l a y – A i r b a g s – B l u e t o o t h L a n e D e p a r t u r e W a r n i n g S y s t e m – A i r c o n d i t i o n i n g – I n s t r u m e n t p a n e l – H e a d - u p d i s p l a y – A i r b a g s – B l u e t o o t h
F 1530 A C e n t r a l l o c k i n g – C h i l d s a f e t y
F 16SHUNT –
F 1740 AVentilation
D A S H B O A R D F U S E S ( B O X C )
Page 216 of 216
565656
IX
F R E Q U E N T LY - A S K E D Q U E S T I O N S
QUESTIONSANSWERSSOLUTIONS
T he rec eption qualit y of the radio station being listened to gradually deteriorates.
The vehicle is too distant from the transmitter, or no transmitter is present in the geographical area you are passing th rough.
Activate the RDS function to allow the system to chec k whether a more power ful transmitter is to be found in the geographical area.
The environment (hills, high buildings, tunnels, underground car parks, etc.) is blocking reception, even in RDS mode.This phenomenon is normal and does not imply anythi ng wrong with the radio.
The aerial is absent or has been damaged (for example after going through a car wash or in an underground car park).Have the aerial checked by a CITROËN dealer.
Cutting of sound for 1 to 2 seconds in radio mode.
The RDS system during this brief sound cut- of f is s earching for a better frequency that might of fer improved reception of the station.
Deactivate the RDS function if the phenomenon occur s too frequently and always on the same journey.
When the engine is not running, the radio stops after a few minutes.
When the engine is switched off, the working time for the radio depends on the batter y charge. The interruption is nor mal: the radio goes into economy mode, cutting off in order to save the vehicle’s batter y.
You have to star t the engine so as to increase the bat-ter y charge.
The message “ the audio system is overheating” appears on the screen.
In order to protect the audio equipment in excessiv e ambient temperatures, the radio goes into an automatic thermic protection mode which results in a reduction in sound volume or stopping of the CD player.
Switch off the audio system for a few minutes in order to allow the system to cool down.
Why is one not informed in real time of a hold-up on the route even though t h e o p t i o n f o r g u i d a n c e b y “ t r a f fi c i n f o ” is activated ?
When you star t up, the system takes a few minutes to c apture t h e t r a f fi c i n f o r m a t i o n v i a R D S - T M C . W a i t f o r t h e t r a f fi c i n f o r m a t i o n t o b e s a f e l y r e c e i v e d (pictogrammes displayed on the map) and make sure that you use the major ar terial roads to have “inform ed” navigation.
Only the major ar terial roads (motor ways and some d ual car- r i a g e w a y s ) a r e f e a t u r e d i n R D S - T M C t r a f fi c i n f o r m a t i o n ) .
I t m a y h a p p e n t h a t a h o l d - u p i s n o t r e p o r t e d b y t h e t r a f fi c i n f o provider.
Why is a diversion not suggested when I h a v e s e l e c t e d t r a f fi c i n f o ?
D o n o t c o n f u s e t h e “ t r a f fi c i n f o ” g u i d a n c e o p t i o n w h i c h c a n s u g -gest a diversion (the “diver t” button appears in the w indow) with t h e m e n u s “ D i s p l a y o f t r a f fi c m e s s a g e s ” o r “ R e a d i n g o f t r a f fi c messages” which af fect only the display without recalculating the itinerar y (no “diver t” button in the window).
To have “informed” navigation with the detour proposi-tion, it is essential to activate the guidance option with “ t r a f fi c i n f o ” .