2008 Citroen C5 LAMP

162
VI
BC
D
EFA
C H A N G I N G B U L B S
H E A D L A M P S
Front headlamp unit with Xenon bulbs (D1S)
Bulbs:
A Sidelamp: W5W
B Dual-function Xenon lamp (dipped/main): D1S
C Angular lighting: HP19
D Daytime-running lamp: HP24
For the maintenance of the front headlamp unit and the changing of HP19, D1S and HP24 bulbs, con-tact a CITROËN dealer, , bulbs, bulbs, .
Front headlamps fi tted with Xenon bulbs: Because of risks of electrocution, we advise you to contact a CITROËN dealer if there is any problem.Front headlamps fi tted with Xenon bulbs: Because of risks of electrocution, we advise you to Front headlamps fi tted with Xenon bulbs: Because of risks of electrocution, we advise you to
You are advised to change the D1S bulbs at the same time, if one of them has failed.
Sidelamp
1 Lift up the pegs E to remove the cover on the headlamp.
2 Remove the protective cap F.
3 Pull the bulb holder to remove it.
4 Replace the bulb and replace the bulb holder.
5 Replace the protective cap F.
6 Replace the cover and fi x it in place using the pegs E.

163
VI
E
ADCBGF
Main beam
1 Lift up the pegs F to remove the cover on the headlamp.
2 Remove the protective cap G.
3 Disengage the retaining spring.
4 Remove the bulb and replace it, paying attention to the direction of fi tting.
5 Replace the retaining spring.
6 Replace the protective cap G.
7 Replace the cover and fi x it in place using the pegs F.
Sidelamp
1 Lift up the pegs F to remove the cover on the headlamp.
2 Remove the protective cap G.
3 Pull the bulb holder to remove it.
4 Replace the bulb and replace the bulb holder.
5 Replace the protective cap G.
6 Replace the cover and fi x it in place using the pegs F.
HEADLAMP UNIT
Bulbs:
A Main beam: H1
B Sidelamp: W5W
C Dipped beam: H7
D Bend lighting: H7
E Daytime-running lamp: HP24
For the maintenance of the front headlamp unit and the changing of HP24 bulbs, contact a CITROËN headlamp unit and the changing of headlamp unit and the changing of
dealer.
Halogen bulbs must not be changed until they have been off for a few minutes (risk of serious burns).
Do not touch the bulb directly with your fi ngers, use a lint-free cloth.
It is essential that only anti-U.V. type bulbs are used in order not to damage the headlamp.
C H A N G I N G B U L B S
H E A D L A M P S

165
VI
BD1C
2
W h e n r e p l a c i n g , b e careful not to pinch the electrical cables.
Front foglamp
1 Remove the fi xing screw of cover A using a torx tool, tip the cover over and remove.
2 Remove the fi xing screw of lamp B using a torx tool and pull the headlamp unit to remove it from the bumper.
3 Disconnect the connector D.
4 Remove the bulb by performing a quarter of a turn.
5 Replace the bulb.
C H A N G I N G B U L B S
H E A D L A M P S
Side repeater
The side repeater is sealed.
If the bulb is faulty, replace the side repeater.
Contact a CITROËN dealer.
6 Connect the connector D.
7 Replace the headlamp unit in the bumper.
8 Screw the headlamp unit in.
9 Position the cover using its guides and screw in.
Bulbs: H8

166
VIB
C
A
E
D
F
H
G
C H A N G I N G B U L B S
R E A R L A M P S ( S A L O O N )
Rear lamp unit
Identify the failed bulb.
Bulbs:
A Stop-lamps and sidelamps: P 21 W / 5 W
B Sidelamp: R 5 W
C Reversing lamp: H 21 W
D Foglamp: H 21 W
E Direction indicator: P 21 W
Rear lamp on boot
1 Open the boot.
2 Using a fl at screwdriver, remove the 3 clips which fi x the trim in the lamp area.
3 Partially remove the trim F.
4 Disconnect the connector G.
5 Detach the bulb holder H.
6 Replace the bulb.
7 Replace the bulb holder H.
8 Connect the connector G.
9 Replace and fi x the trim F with its clips.
In some climatic conditions, mist may appear on the headlamp / indicator lenses. This is normal and will disappear (e.g. after the lamps have been on for a few minutes). If not, contact a CITROËN dealer.few minutes). If not, contact few minutes). If not, contact

167
VI
A
B
CD
C H A N G I N G B U L B S
R E A R L A M P S ( S A L O O N )
Rear lamp on wing
1 Remove the lateral boot trim fl ap A. To do so, pull it towards the inside of the boot, then pull it upwards.
2 Disconnect connector B.
3 Unscrew the 2 fi xings C.
4 Remove the lamp from its housing.
5 Detach the bulb holder D.
6 Replace the bulb.
7 Replace the bulb holder D.
8 Place the lamp in its housing.
9 Screw in the 2 fi xings C.
10 Connect connector B.
11 Refi t the trim A.
Note: You can use the spare wheel jack handle to screw or unscrew the fi xings C.

168
VI
B
C
A
EDF
H
G
C H A N G I N G B U L B S
R E A R L A M P S ( T O U R E R )
Rear lamp unit
Identify the failed bulb.
Bulbs:
A Stop-lamp and sidelamp : P 21 W / 5 W
B Sidelamp : R 5 W
C Reversing lamp : H 21 W
D Foglamp : H 21 W
E Direction indicator: P 21 W
Rear lamp on boot
1 Open the boot.
2 Using a fl at screwdriver, remove the 3 clips which fi x the trim in the lamp area.
3 Partially remove the trim F.
4 Disconnect the connector G.
5 Detach the bulb holder H.
6 Replace the bulb.
7 Replace the bulb holder H.
8 Connect the connector G.
9 Replace and fi x the trim F with its clips.In some climatic conditions, mist may appear on the headlamp / indicator lenses. This is normal and will disappear (e.g. after the lamps have been on for a few minutes). If not, contact a CITROËN dealer.few minutes). If not, contact few minutes). If not, contact

169
VI
A
B
CD
A
1
2
1
2
C H A N G I N G B U L B S
R E A R L A M P S ( T O U R E R )
Rear lamp on wing
Remove the lateral boot trim A.
To do so :
1 Pull it towards towards the inside of the boot.
2 Pull it upwards.
3 Disconnect the connector B.
4 Unscrew the fi xing screw C.
5 Remove the lamp from its housing.
6 Detach the bulb holder D.
7 Replace the faulty bumb.
8 Replace the bulb holder D.
9 Place the lamp in its housing.
10 Screw in the fi xing screw C.
11 Connect the connector B.
12 Refi t the trim A.
Note : You can use the spare wheel jack handle to screw or unscrew the fi xing screw C.

170
VI
C H A N G I N G B U L B S
R E A R L A M P S
Third stoplamp
The third stoplamp uses diodes which cannot be replaced.
In case of malfunction, contact a CITROËN dealer.In case of malfunction, contact In case of malfunction, contact
Number plate
1 Using a fl at screwdriver, detach the transparent cover by lever-ing it into the notch provided.
2 Lift up and pull the transparent cover.
3 Using a small fl at screwdriver, remove the faulty bulb.
4 Fit the new bulb by fi rstly plac-ing the angled base on the axis of the clips, then press the bulb in to insert.
5 Refi t the transparent cover by inserting it from the edge oppo-site the notch, then press on the edge of the transparent cover.
After each operation, check that the lamps work.
Bulb: W 5W