2008 Citroen C5 DAG light

140
IV
B L U E T O O T H®
Voice recognition
Pressing on the end of the lighting control stalk 10 starts telephone voice recognition.
Voice recognition allows you to make a call to a number for which you have recorded a label on the mobile telephone that is twinned and connected.
Remark:
It is possible to stop the call, pro-vided the dialling has not yet com-menced, with a short press on the end of the lighting control stalk 10.
Remarks:While you are on a call, the audio source currently being listened to is paused.
Some ring tones on your mobile telephone may not be recog-nised by the Bluetooth®telephone may not be recog-telephone may not be recog- system ®
on your vehicle. A different ring tone will be chosen by the sys-tem.

152
V
D I E S E L I N J E C T I O N E Q U I P M E N T
In the event of running out of fuel:
HDi 110 engineHDI 138 and HDi 173 engines
V6 HDi 208 engine with priming pump
After adding fuel, turn the ignition key to position M, wait for a few seconds, then operate the starter motor until the engine starts.
If the engine fails to start after sev-eral attempts, contact a CITROËN If the engine fails to start after sev-after sev-
dealer.
HDi 110, HDi 138 and HDi 173 engines with priming pump
After fi lling (minimum 5 litres) and removing the protective cover, action the manual priming pump, until some resistance is felt.
Operate the starter motor while depressing the accelerator pedal slightly until the engine starts.
If the engine fails to start at the fi rst attempt, wait 15 seconds before trying again.
If the engine fails to start after a few attempts, action the priming pump again and then try to start the engine.
When the engine is idling, acceler-ate slightly to complete the bleed-ing of the circuit.

155
V
+ 1
- 4- 3
+ 2
A
B
C
1 2 V B A T T E R Y
V 6 H Di E N G I N E
Starting the engine with an assisting battery
If the battery is discharged, it is possible to use either a separate emergency battery or a battery on another vehicle.
If you use the battery on another vehicle, stop the engine on the latter. The two vehicles must not come into direct contact with each other.
Check that the assisting battery has suffi cient voltage (12 V).
Lift up the pegs to remove the front left-hand headlamp cover.
Connect the cables according to the order indicated in the dia-ordergram.
A Pole “+” of the broken down vehicle (Under the red cover).B Assisting battery.C Pole “–” of the broken down vehicle (Under the bonnet).
Check that the leads are well secured (risk of sparks).
Start the engine of the assist-ing vehicle. Let the engine run for around 1 minute at a slightly accel-erated idle.
Operate the starter on the vehicle being assisted.
It is essential to follow the indi-cated sequence correctly.
Never approach with a fl ame or create sparks in the vi
cinity of the battery (explosive gas).
The battery contains dilute sulphuric acid which is hig hly corrosive.
When handling batteries, always protect your face and es pecially your eyes.
In the event of any contact with the skin, rinse immediatel y with copious amounts of fresh water.
For any battery replacement, contact a CITROËN dealer.
Do not touch the leads during the operation.
Do not lean over the batteries.
Disconnect the cables in reverse order, making sure they do not touch together.
Advice
Battery location and access
The battery is located in the boot under the left hand wing trim. To access the battery, open the fl ap.
IMPORTANT
In the event of a battery failure, and if the boot is closed, it is then necessary to feed an electrical supply to your vehicle.

157
V
T A B L E O F F U S E S
Fusebox A
Ref.RatingFunction
G29--
G305AHeated rear view mirrors
G315ARain and brightness sensor
G325ASeat belt not fastened warning lamps
G335AElectrochrome rear view mirrors
G3420ASunroof (saloon)
G355APassenger door lighting - Passenger rear view mirror adjustment
G3630AElectric tailgate (Tourer)
G3720AHeated front seats
G3830ADriver’s electric seat
G3930APassenger’s electric seat - HIFI amplifi er
G403ATrailer relay unit supply
Ref.RatingFunction
G3615A6 speed automatic gearbox
5A4 speed automatic gearbox
G3710ADaytime-running lamps - Diagnostic socket
G383AESP
G3910AHydraulic suspension
G403ASTOP switch
Fusebox B

158
V
T A B L E O F F U S E S
Fusebox C
Ref.RatingFunction
F115ARear screen wipe (Tourer)
F230ALocking and deadlocking relay
F35AAirbags
F410AAutomatic gearbox - Additional heater unit (Diesel) - Electrochrome rear view mirrors
F530AFront window - Sun roof - Passenger door lighting - Passenger rear view mirror adjustment
F630ARear window
F75AVanity mirror lighting – Glove box lighting – Interior lamps - Torch (Tourer)
F820ARadio - CD changer - Controls at the steering wheel – Displa y – Tyre defl ation detection - Electric boot ECU
F930ACigar-lighter - Front 12V socket
F1015AAlarm - Controls on the steering wheel, signalling and screen w ipe controls
F1115ALow current anti-theft switch
F1215ADriver’s electric seat - Instrument panel - Seat belt not fastened warning lamps - Air conditioning controls
F135AEngine relay unit - Hydraulic suspension pump cut-off relay - Airbag ECU supply
F1415ARain and brightness sensor - Parking assistance - Passenger’s electric sea t - Trailer relay unit - HIFI amplifi er ECU - Hands-free kit - Lane Departure Warning System
F1530ALocking and deadlocking relay
F1740AHeated rear screen - Exterior heated rear view mirrors
FSHSHUNTCUSTOMER PARK SHUNT

162
VI
BC
D
EFA
C H A N G I N G B U L B S
H E A D L A M P S
Front headlamp unit with Xenon bulbs (D1S)
Bulbs:
A Sidelamp: W5W
B Dual-function Xenon lamp (dipped/main): D1S
C Angular lighting: HP19
D Daytime-running lamp: HP24
For the maintenance of the front headlamp unit and the changing of HP19, D1S and HP24 bulbs, con-tact a CITROËN dealer, , bulbs, bulbs, .
Front headlamps fi tted with Xenon bulbs: Because of risks of electrocution, we advise you to contact a CITROËN dealer if there is any problem.Front headlamps fi tted with Xenon bulbs: Because of risks of electrocution, we advise you to Front headlamps fi tted with Xenon bulbs: Because of risks of electrocution, we advise you to
You are advised to change the D1S bulbs at the same time, if one of them has failed.
Sidelamp
1 Lift up the pegs E to remove the cover on the headlamp.
2 Remove the protective cap F.
3 Pull the bulb holder to remove it.
4 Replace the bulb and replace the bulb holder.
5 Replace the protective cap F.
6 Replace the cover and fi x it in place using the pegs E.

163
VI
E
ADCBGF
Main beam
1 Lift up the pegs F to remove the cover on the headlamp.
2 Remove the protective cap G.
3 Disengage the retaining spring.
4 Remove the bulb and replace it, paying attention to the direction of fi tting.
5 Replace the retaining spring.
6 Replace the protective cap G.
7 Replace the cover and fi x it in place using the pegs F.
Sidelamp
1 Lift up the pegs F to remove the cover on the headlamp.
2 Remove the protective cap G.
3 Pull the bulb holder to remove it.
4 Replace the bulb and replace the bulb holder.
5 Replace the protective cap G.
6 Replace the cover and fi x it in place using the pegs F.
HEADLAMP UNIT
Bulbs:
A Main beam: H1
B Sidelamp: W5W
C Dipped beam: H7
D Bend lighting: H7
E Daytime-running lamp: HP24
For the maintenance of the front headlamp unit and the changing of HP24 bulbs, contact a CITROËN headlamp unit and the changing of headlamp unit and the changing of
dealer.
Halogen bulbs must not be changed until they have been off for a few minutes (risk of serious burns).
Do not touch the bulb directly with your fi ngers, use a lint-free cloth.
It is essential that only anti-U.V. type bulbs are used in order not to damage the headlamp.
C H A N G I N G B U L B S
H E A D L A M P S

164
VI
A
HIFront direction indicator
1 Remove the fi xing screw of cover A using a torx tool, tip the cover over and remove.
2 Remove the fi xing screw of lamp B using a torx tool and pull the headlamp unit to remove it from the bumper.
3 Detach the bulb C by pressing on bars 1 and 2.
4 Disconnect the connector (pull whilst pressing on the grey tongue using a fl at screwdriver).
5 Replace the bulb.
6 Connect the connector (push the grey tongue in well).
7 Replace the headlamp unit in the bumper.
8 Screw the headlamp unit in.
9 Position the cover using its guides and screw in.
Bulbs: HP24W
Dipped beam
1 Lift up the pegs F to remove the cover on the headlamp.
2 Remove the protective cap H.
3 Disconnect the connector by pressing it between the thumb and index fi nger.
4 Free the bulb from its two metal clamps.
5 Take out the bulb.
6 Replace the bulb, exerting a slight axial force.
7 Reconnect the connector, until it is all the way in.
8 Replace the protective cap H.
9 Replace the cover and fi x it in place using the pegs F.
Bend lighting
1 Lift up the pegs F to remove the cover on the headlamp.
2 Remove the protective cap I.
3 Disconnect the connector by pressing it between the thumb and index fi nger.
4 Free the bulb from its two metal clamps.
5 Take out the bulb.
6 Replace the bulb, exerting a slight axial force.
7 Reconnect the connector, until it is all the way in.
8 Replace the protective cap I.
9 Replace the cover and fi x it in place using the pegs F.
C H A N G I N G B U L B S
H E A D L A M P S