88
II
Stopping the function
- by an action on the control on position "REG" to position 0.
- by the engine stopping.
The cruise speed previously cho-sen is no longer memorised.
If there is a malfunction,a mes-sage will display accompanied by a sound signal and lighting of the SERVICE warning lamp.
Contact a CITROËN dealer.
Cruise control should only be used when the driving conditions allow you to drive at a constant speed.
D o n o t u s e i t i n h e a v y t r a f fi c , o r o n d a n g e r o u s o r s l i p p e r y r o a d s .
The driver must remain attentive and in full control of his vehicle.
You are recommended to keep your feet within range of the pe dals.
To avoid any risk of interfering with the pedals :
- c h e c k t h a t t h e fl o o r m a t i s c o r r e c t l y p o s i t i o n e d ,
- n e v e r u s e m o r e t h a n o n e fl o o r m a t .
Re-engaging cruise control
-by recall of the memorised speed :
After a disengagement, press on button 3. Your vehicle automati-cally returns to the memorised cruise speed which is displayed in zone A.
If the memorised cruise speed is higher than the current speed, the vehicle wll accelerate to reach the former.
- by selection of the current speed :
Press on button 2 or 4 once the desired speed has been reached.The information "OFF" will thendisappear from zone A.
Observation : If during the opera-tion of cruise control, the system is unable to keep within the memo-rised speed (for example on a steep d e s c e n t ) , t h e n t h e s p e e d fl a s h e s . Adapt your speed as necessary.
Disengaging of cruise control while retaining the memorised speed
- Either by pressing on the brake pedal or on the clutch pedal.
- Or by pressing button 3.
- Or if either the ESP or the ASR system is active.
Note : cruise control is not active if the gear lever is in neutral.
These actions cause the informa-tion "OFF" to appear in zone A of the instrument panel.
These manœuvres do not cancel the cruise speed which remains displayed in the instrument panel.
C R U I S E C O N T R O L
90
II
Stopping the function
- by an action on the control on position "LIM" to position 0.
- by the engine stopping.
The speed previously chosen is still memorised.
If there is a malfunction,a mes-sage will display accompanied by a sound signal and lighting of the SERVICE warning lamp.
Contact a CITROËN dealer.
Temporary override of the m a x i m u m s p e e d
The accelerator pedal is equipped with an end-of-travel switch. If you action this switch by pressing the pedal hard down, you can exceed the memorised maximum speed at any time.
During the time the speed is being exceeded, the displayed speed fl a s h e s .
You have only to release the ac-celerator pedal to return below the maximum speed and render the function active again.
Observation : If during the operation of the speed limiter, the system is unable to keep within the maximum speed (for example on a steep de-scent or under heavy acceleration) t h e n t h e s p e e d fl a s h e s . A d a p t y o u r speed as necessary.
The function will re-engage when your speed returns below the de-sired maximum speed.
Disengagement of the m a x i m u m s p e e d
Press on button 3.
This action causes the information "OFF" to appear on the instru-ment panel screen.
U s e o f fl o o r m a t s t h a t a r e n o t a p p r o v e d b y C I T R O Ë N m a y h i n d e r access to the accelerator pedal and thus interfere with the func-tioning of the speed limiter.
To avoid any risk of interfering with the pedals :
- c h e c k t h a t t h e fl o o r m a t i s c o r r e c t l y p o s i t i o n e d ,
- n e v e r u s e m o r e t h a n o n e fl o o r m a t .
This action does not cancel the memorised maximum speed which remains displayed in zone A ofthe instrument panel.
S P E E D L I M I T E R