2008 Citroen C4 PICASSO warning
[x] Cancel search: warningPage 54 of 266
II
55
M a n u a l g e a r b o x
1.Check that you are in neutral.
2. Do not touch the accelerator.
3. For Diesel engines : turn the key as far as position M. Wait for the preheater warning lamp to go off if this has come on.
4. Action the starter by turning the key until the engine starts ( n o t m o r e t h a n t e n s e c o n d s ) .
5. In ambient temperatures low-er than 0°C, declutch during the action on the starter to fa-cilitate starting. Then remove your foot slowly from the clutch pedal.
NEVER RUN THE ENGINE IN A SPACE THAT IS ENCLOSED OR INSUFFICIENTLY VENTILATED.
E l e c t r o n i c G e a r b o x S y s t e m ( 6 - s p e e d )
1.Check that you are in position N.
2. P r e s s fi r m l y o n t h e b r a k e p e d a l.
3. Do not touch the accelerator. 4.For Diesel engines : turn the key as far as position M. Wait for the preheater warning lamp to go off if this has come on.
5. Action the starter by turning the key until the engine starts ( n o t m o r e t h a n t e n s e c o n d s ) .
Note : After the vehicle has had a prolonged stop or if the brake ped-al has been applied several times when stationary, it is necessary to press the brake pedal fully down in order to authorise starting of the engine.
Advice
V e h i c l e s e q u i p p e d w i t h a t u r b o c h a r g e r
Never stop the engine without having allowed it to run for a few seconds at idle, this being the time required for t he turbocharger to return to a normal speed.
"Flicking the accelerator" at the moment of switching off the i gnition could cause serious damage.
Note : I f t h e e n g i n e f a i l s t o s t a r t a t t h e fi r s t a t t e m p t , s w i t c h o f f t h e i g n i t i o n . W a i t t e n s e c o n d s , t h e n a c t i o n t h e s t a r t e r again as indicated above.
A u t o m a t i c g e a r b o x
1. Check that you are in position P or N.
2. Do not touch the accelerator.
3. For Dieselengines: turn the key as far as position M. Wait for the preheater warning lamp to go off if this has come on.
4. Action the starter by turning the key until the engine starts ( n o t m o r e t h a n t e n s e c o n d s ) .
Note : To exit from position P, press on the brake pedal before moving the selector.
S T A R T I N G T H E E N G I N E
Page 57 of 266
58
II
S t a r t i n g t h e e n g i n e
1. To start the engine, the selec-tor has to be in position N.
2. P r e s s fi r m l y o n t h e b r a k e p e d a l.
3. Action the starter.
4. When the engine is running, place the selector on R, A or M as desired.
5. Check, in the instrument pan-el, the position engaged.
6. Release the brake pedal and accelerate.
Note : If the selector is not in po-sition N , a n d / o r i f t h e b r a k e p e d a l is not pressed, the correspond- i n g w a r n i n g l a m p ( s ) d i s p l a y a n d a message informs you that at least one of these two conditions is not met.
In this case, the engine will not start, recommence the above pro-cedure.
U s i n g t h e 6 - s p e e d e l e c t r o n i c g e a r b o x
R e v e r s e g e a r
E n g a g i n g r e v e r s e g e a r
To engage reverse gear, move the selector to R.
O n l y a t t e m p t t o c h a n g e t o r e v e r s e g e a r w h e n t h e v e h i c l e i s s t a t i o n a r y.
Automatic mode
C h a n g i n g t o a u t o m a t i c m o d e
To change to automatic mode, move the selector to A.
Manual mode
C h a n g i n g t o m a n u a l m o d e
Manual mode activates when you move the selector to M.- Pull the lever “ + ” to change up a gear.- Pull the lever “ - ” to change down a gear.
When the engine is running, be-fore accelerating to move the ve-hicle, make sure that the position engaged on the selector grille or in the instrument panel is either : R, A or AM.Do not leave the vehicle with the engine running in R, A or AM.
If the vehicle is moving rapidly, if an inadvertent attempt to engage reverse gear is made, the warning lamp N w i l l fl a s h a n d y o u r v e h i c l e will go automatically into neutral. To re-engage a gear, you have only to reposition the selector on A, Mor R.
( 6 - S P E E D ) E L E C T R O N I C G E A R B O X S Y S T E MG E N E R A L ( 6 - S P E E D ) E L E C T R O N I C G E A R B O X S Y S T E M ( 6 - S P E E D ) E L E C T R O N I C G E A R B O X S Y S T E M
Neutral
C h a n g i n g t o n e u t r a l
To change to neutral, move the selector to N. If the vehicle is mov-ing, do not select this position even momentarily.
Page 58 of 266
–+
II
59
To select automatic d r i v i n g m o d e :
- Move the selector to position A. The warning lamp A lights up in t h e i n s t r u m e n t p a n e l t o c o n fi r m the selection.
The gearbox then functions in au-tomatic mode, without any inter-vention on your part.
It constantly selects the gear that is best suited to the following pa-rameters :
- driving style,
- r o a d p r o fi l e ,
- optimum fuel consumption.
Temporary manual operation when in automatic mode
- By pulling either of the levers “+” or “-”, you can exercise tempo-rary control over the changing of gears. The request to change gear will be taken into account. Y o u w i l l s t i l l b e i n a u t o m a t i c mode. The warning lamp A re-mains lit up in the instrument panel.
- This function enables you to an-ticipate certain situations such as the approach of a bend or the need to overtake another vehi-cle.
( 6 - S P E E D ) E L E C T R O N I C G E A R B O X S Y S T E MA U T O M A T I C M O D E ( 6 - S P E E D ) E L E C T R O N I C G E A R B O X S Y S T E M ( 6 - S P E E D ) E L E C T R O N I C G E A R B O X S Y S T E M
Cancellation of automatic mode
The change from position A ( d r i v -ing in automatic mode) to position M ( d r i v i n g i n m a n u a l m o d e ) o r v i c e versa can be made at any time. The warning lamp A disappears in the instrument panel.
Page 60 of 266
II
Do not use the accelerator to hold your vehicle on a gradient. Use either the brake pedal or the electric parking brake.
Before taking any action in the engine compartment, check that the selector is in neutral N.
( 6 - S P E E D ) E L E C T R O N I C G E A R B O X S Y S T E MG E N E R A L ( 6 - S P E E D ) E L E C T R O N I C G E A R B O X S Y S T E M ( 6 - S P E E D ) E L E C T R O N I C G E A R B O X S Y S T E M
Acceleration
F o r o p t i m u m a c c e l e r a t i o n ( e . g . t o o v e r t a k e a n o t h e r v e h i c l e ) , y o u o n l y h a v e t o a p p l y t h e a c c e l e r a t o r p e d a l b e y o n d t h e e n d - o f - t r a v e l s w i t c h , b y p r e s s i n g d o w n fi r m l y .
V e h i c l e s t a t i o n a r y w i t h t h e e n g i n e r u n n i n g
In the event of a prolonged stop with the engine running, the gearbox changes automatically to neutral N.
S t o p p i n g t h e e n g i n e
Before stopping the engine, you can choose :
- to leave the vehicle in neutral : move the selector to posi tion N.
- t o l e a v e t h e v e h i c l e w i t h a g e a r e n g a g e d (R, A or M) : Place the selector in the chosen position prior to stopping the engine. In this case, the vehicle cannot be moved.
In all cases, it is essential to apply the parking brake. Check that the parking brake warning lamp is lit up in the instrument panel.
Page 64 of 266
–+II
65
T h e fl a s h i n g o f t h e w a r n i n g l a m p f o r t h e p o s i t i o n r e q u e
s t e d s i g n a l s t h a t t h i s p o s i t i o n i s n o t y e t o b t a i n e d . I f t h e w a r n i n g l a m p i s o n fi x e d , t h e p o s i t i o n i s c o n fi r m e d .Display of a dash in the rev counter indicates a malfunction. Urgently contact a CITROËN dealer. I f t h e w a r n i n g l a m p i s o n fi x e d , t h e p o s i t i o n i s c o n fi r m e d . I f t h e w a r n i n g l a m p i s o n fi x e d , t h e p o s i t i o n i s c o n fi r m e d .
Lighting of the SERVICE warning lamp accompanied by a message an d a sound signal indicates a functioning anomaly. In this case :
- a marked snatching may be felt when selecting R for reverse gear,- the gearbox is locked on a gear, - d o n o t e x c e e d 1 0 0 k m / h ( a p p r o x . 6 0 m p h ) .
Urgently contact a CITROËN dealer.
Sequential mode w i t h m a n u a l g e a r c h a n g i n g
Position of the selector for manual gear changing.
- Move the selector to position M.
- Pull the lever “ + ” to change up a gear.
- Pull the lever “ - ” to change down a gear.
A U T O M A T I C G E A R B O X S E Q U E N T I A L M O D E
Observations :
- If the vehicle stops or reduces s p e e d ( f o r e x a m p l e w h e n a p -proaching a stop sign), the gear-box changes down automatically t o fi r s t g e a r .
- In sequential mode, it is not necessary to release the accel-erator during gear changes.
- A request to change gear is ac-cepted only if the engine speed permits it.- For safety reasons, depending on the engine speed, a change up or down may be performed automatically.
- It is possible at any time to move from position D ( d r i v i n g i n a u t o -matic mode) to position M ( d r i v -ing in sequential mode) or vice versa.
Page 65 of 266
66
II A B S - A n t i - l o c k b r a k i n g s y s t e m
This system enhances your safety by preventing the wheels from locking under heavy braking or in conditions of poor road adherence.
It enables you to retain control of the steering.
The operating capacity of all the electrical components that are essential to the ABS system is checked by an electrical monitoring system before and during your journey. The ABS warning lamp comes on when you switch on the ignition and should go out after a few seconds.
If the warning lamp does not go out, this means that the ABS has discon-nected as a result of a malfunction. Also, if the warning la mp lights up dur-ing a journey, it means that the ABS system is inactive. In eith er case, the normal braking system remains fully effective, as on a non-ABS vehicle.
However, to restore the safety associated with the correct operat ion of the ABS, the vehicle should be examined as soon as possible by a CITR OËN However, to restore the safety associated with the correct operation of the operation of the
dealer.
O n s l i p p e r y s u r f a c e s ( g r a v e l , s n o w , i c e , e t c . ) , d r i v i n g c a r e f u l l y i s s t i l l e s -sential.
E m e r g e n c y b r a k i n g a s s i s t a n c e s y s t e m
In an emergency, this system enables you to achieve the optimum braking pressure more quickly, thereby reducing the stopping distance. It deploys according to the speed of your action on the brake pedal, reducing the resistance to that action.
To prolong the effect of the emergency braking assistance, simply keep your foot on the brake pedal.
B R A K E S
State of wear of brake pads, discs and drums
Brake pad wear varies according to the way you use your vehicle ( e . g . u r b a n d r i v i n g , f r e q u e n t s t o p s , your style of driving or the type of road).
For all information relating to the checking of the state of wear of brake discs and drums, contact a CITROËN dealer.brake discs and drums, brake discs
After washing, apply the brakes gradually to remove water from the brake linings.
Page 66 of 266
AII
67
The electronic parking brake com-bines 2 operational modes :
- AUTOMATIC :
Automatic application when the engine stops and automatic re-lease on use of the accelerator ( a u t o m a t i c o p e r a t i o n b y d e f a u l t ) ,
- MANUAL :
P e r m a n e n t m a n u a l a p p l i c a t i o n / release of the parking brake is possible by pulling control A.
AUTOMATIC OPERATION
To start the vehicle
The electronic parking brake re-leases automatically and pro- g r e s s i v e l y when you press the accelerator :
- with a m a n u a l g e a r b o x ( m a n u a l g e a r b o x m a n u a l g e a r b o x fi r s t g e a r or r e v e r s e g e a r engaged), press down fully on the clutch pedal then press on the accelera-tor pedal and move off.- with an a u t o m a t i c g e a r b o x, ac-celerate with the selector in posi-tion D, M or R.- with an e l e c t r o n i c g e a r b o x, ac-celerate with the selector in posi-tion A, M or R.
To immobilise the vehicle
I m m o b i l i s a t i o n , e n g i n e o f f
With the vehicle stationary, the park-ing brake is automatically applied w h e n t h e e n g i n e i s s w i t c h e d o f f.
E L E C T R O N I C P A R K I N G B R A K E
Full release of the parking b r a k e i s c o n fi r m e d b y :
- the extinction of warning lamp Pon control A and on the instru-ment panel,
- the display of a message “park-ing brake released” on the multi-function display.
Before leaving the vehi-cle, check that warning lamp P on the instrument panel is permanently lit.
Never leave a child alone inside the vehicle with the ignition on, as they could release the park-ing brake.
The application of the park- i n g b r a k e i s c o n fi r m e d b y :
- the lighting of warning lamp P on control A and on the instrument panel,
- the display of a message “park-ing brake applied” on the multi- f u n c t i o n d i s p l a y ( e x c e p t D T ) .
Note: an operation sound will c o n fi r m t o y o u t h e a p p l i c a t i o n / r e -lease of your electronic parking brake.
Page 67 of 266
A
68
II
I m m o b i l i s a t i o n , e n g i n e r u n n i n g
With the engine running and the vehicle stationary, in order to im-mobilise the vehicle you need to manually apply the parking brake by p u l l i n g on control A.
The application of the park- i n g b r a k e i s c o n fi r m e d b y :
- the lighting of warning lamp P on control A and on the instrument panel,
- the display of a message “park-ing brake applied” on the multi-function display.
When the driver’s door is opened, a beep is heard and a message displayed if the parking brake has not been applied.
A C T I V A T I O N / D E A C T I V A T I O N O F
THE AUTOMATIC FUNCTIONS
The automatic application when the en-gine is switched off and the automatic release when you press the accelerator c a n b e d e a c t i v a t e d . A c t i v a t i o n / d e a c t i -vation is performed using the Menu of the instrument panel screen. To do so, s e l e c t “ P e r s o n a l i s a t i o n / C o n fi g u r a t i o n / D e fi n e t h e V e h i c l e p a r a m e t e r s / D r i v i n g a s s i s t a n c e / A u t o m a t i c h a n d b r a k e ” .
The deactivation of these f u n c t i o n s i s c o n fi r m e d b y t h e lighting of this warning lamp on the instrument panel.
With the automatic functions de-activated, the application and re-lease of the parking brake are done manually.
The full application of the park- i n g b r a k e i s c o n fi r m e d b y :
- the extinction of the warning lamp on control A and of warning lamp P on the instrument panel,
- the display of a message “park-ing brake released” on the multi-function display.
Note : If you pull control Awithout pressing the brake pedal, the parking brake will not be released and the “foot on brake” warning lamp will light up on the instrument panel.
E L E C T R O N I C P A R K I N G B R A K E
Before leaving the vehi-cle, check that warning lamp P on the instrument panel is permanently lit.
The deactivation of the automat-ic functions is recommended in p a r t i c u l a r l y c o l d c o n d i t i o n s ( i c e ) a n d d u r i n g t o w i n g ( b r e a k d o w n , caravan, ...)
MANUAL OPERATION
M a n u a l a p p l i c a t i o n / r e l e a s e o f t h e parking brake is always possible.
To start the vehicle
With the ignition on or the engine running, to release the parking brake, press on the brake pedal, pull then release control A.
When stationary, with the engine running, do not press the accelerator pedal unnecessarily, as you may release the parking brake.