2008 Citroen C4 PICASSO display
[x] Cancel search: displayPage 72 of 266
II
73If any of these instances arises, contact a CITROËN dealer as soon as possible.
E L E C T R O N I C P A R K I N G B R A K EO P E R A T I N G A N O M A L I E S
SITUATIONCONSEQUENCES
4Display of message “ P a r k i n g b r a k e f a u l t y”and the following warning lamps :
a n d / o r fl a s h i n g fl a s h i n g fl a s h i n g a n d / o r a n d / o r
- The automatic functions are deactivated.
- The hill start assist is unavailable.
To apply the electronic parking brake :
1. Immobilise the vehicle and switch off the ignition.
2. Pull the control lever for at least 5 seconds or until maximum application.
3. Switch on the ignition and check that the electronic parking brake warning lamps are on.
Note : - Application may take longer than in normal operation.
- If warning lamp P fl a s h e s o r i f t h e w a r n i n g l a m p s d o n o t come on when the ignition is switched on, this method does not work. Contact a CITROËN dealer. come on when the ignition is switched on, this switched
To release the electronic parking brake :
1. Switch on the ignition.
2. Pull the control lever and hold it for approximately 3 seconds.
5Display of message “ P a r k i n g b r a k e c o n - t r o l f a u l t y – a u t o m a t i c m o d e a c t i v a t e d ”and the following warning lamps :
a n d / o r fl a s h i n g fl a s h i n g fl a s h i n g a n d / o r a n d / o r
- Only the functions for automatic application on switching o ff the engine and automatic release on acceleration are avail-able.
- M a n u a l a p p l i c a t i o n / r e l e a s e o f t h e e l e c t r o n i c p a r k i n g b r a k e and dynamic emergency braking are unavailable.
6Battery fault- Lighting of the battery warning lamp makes it essential to s t o p t h e v e h i c l e a s s o o n a s t r a f fi c a l l o w s . S t o p a n d i m m o b i -lise your vehicle.
- Apply the electronic parking brake before switching off the engine.
Page 74 of 266
AII
75
You can select the “parking space sensor” function by pressing button A . T h e fi x e d l i g h t i n g o f t h e w a r n i n g lamp indicates that the function is selected.
Parking space sensor warning lamp
This warning lamp can have three different statuses :
- off : the function is not selected.
- o n fi x e d : the function is selected but the conditions for mea
suring are not yet met (direction indicator not operating, speed too high) or the measuring phase is terminate d.
- fl a s h i n g : the measuring is in progress or the message is being displayed.
T h e p a r k i n g s p a c e s e n s o r f u n c t i o n a s s i s t s y o u i n fi n d i n g a p a r k i n g s p a c e . it measures the size of the space and gives you information on :
- t h e p o s s i b i l i t y o f fi t t i n g i n t o a f r e e s p a c e , d e p e n d i n g o n t h e d i m e n s i o n s o f your vehicle and the distances necessary for your manœuvring,
- t h e l e v e l o f d i f fi c u l t y o f t h e m a n œ u v r e t o b e p e r f o r m e d .
Note : The system does not measure spaces which are clearly much smaller or larger than the size of the vehicle.
P A R K I N G S P A C E S E N S O R
Page 75 of 266
76
II
If there is a malfunction, have the system checked by a CITROËN dealer.
The function displays the following types of message :Operation :
Y o u h a v e i d e n t i fi e d a p a r k i n g s p a c e :
1. Press button A to select the function.
2. Activate the direction indicator on the side where the space is to be measured.
3. During the measuring, go for-ward the length of the space, at a speed less than 20 km/h (approx. 12 mph), to prepare for your manœuvre.
The system then measures the size of the space.
4. The system informs you of t h e l e v e l o f d i f fi c u l t y o f t h e manœuvre via a message on the multifunction screen ac-companied by a gong.
5. Depending on the message is-sued by the system, you may or may not be able to perform the manœuvre.
Parking possible
P a r k i n g d i f fi c u l t
Parking not advised
Note : The function deselects itself automatically :
- when you engage reverse gear,
- when you switch off the ignition,
- if measuring is not requested,
- w i t h i n fi v e m i n u t e s o f s e l e c t i o n of the function,
- if the vehicle speed exceeds the threshold of 70 km/h (approx. 45 mph) for one minute.
Warning : if the lateral distance be-tween your vehicle and the parking space is too large, the system may not be able the measure the space.
Notes :
- The function remains available after each measurement and thus can measure more than one space during your search.
- In bad weather conditions or in winter, make sure that the sen-sors are not covered by dirt, or by ice or snow.
- The parking space sensor func-tion deactivates the front park-ing assistance during the space measuring phase when you are in forward gear.
P A R K I N G S P A C E S E N S O R
Page 76 of 266
A
II
77
SAFETY RECOMMENDATIONS
The ESP system offers increased driving safety but is not in place to encourage the driver to take addi-tional risks or to drive at excessive speeds.
The functioning of this system is subject to compliance with the manufacturer’s recommendations on wheels (tyres and rims), brake parts and electronic components, as well as with CITROËN’s as-parts and electronic components, components,
sembly and repair procedures.
After any collision, have this system checked by a CITROËN dealer.After any collision, have this system , have t
Electronic stability programme (ESP) and traction control (ASR)
These systems are closely connected to the ABS and additional to it. In the event of a loss of control of the vehicle by the driver, the ESP system acts automatically on one or more brakes and also on the engine to bring the vehicle back on trajectory. The ASR system optimises traction and prevents wheel spin by acting on the brakes of the driving wheels, as well as on the engine. It also improves steering stability during acceleration.
Operation :
When either the ESP or ASR system is in operation, the ESP/ASR warning l a m p fl a s h e s.
Deactivation
In exceptional conditions (vehicle stuck in snow, soft ground, e tc.) it may prove useful to deactivate the ESP/ASR system to allow the wheels to spin and thus regain traction.
- Press on control A, the ESP/ASR warning lamp and the control light up. The ESP/ASR systems are no longer active.
The ESP/ASR systems will activate again :
- Automatically after the ignition has been switched off.
- Automatically above a speed of 50 km/h (30 mph).
- Manually with a new press on control A.
Operational anomaly
If the systems malfunction, the ESP/ASR warning lamp comes on, ac-companied by a sound signal and a message on the multifunction display. Contact a CITROËN dealer to have the system checked.companied by a sound signal and a message on the multifunction by a sound
E L E C T R O N I C S T A B I L I T Y P R O G R A M M E
Page 88 of 266
A
1
3
4
2II
87
This driving assistance device enables you to drive at a constant speed of your choice, without the need to action the accelerator. It is active over speeds of around 40 km/h (approx. 25 mph).
The cruise control commands are located on the steering wheel.
Note : The information relating to the cruise control is displayed in zone A of the instrument panel.
Selection of the function
Rotate the control 1 to the "REG"position.
Selection of a cruise speed
On selection of the function via control 1, no cruise speed has yet been memo-rised.
Once the desired speed has been reached via action on the accel-erator, press button 2 or button 4. The cruise speed is then memo-rised. It is displayed in zone A of the instrument panel.
You can then release the accelera-tor pedal. The vehicle will automati-cally keep to the speed chosen.
Note : The speed of your vehicle may vary slightly in relation to that memorised.
If during the operation of cruise control, the system is unable to keep within the memorised speed (for example on a steep descent), t h e n t h e s p e e d fl a s h e s . A d a p t y o u r speed as necessary.
Bi-tone instrument panel
Adjustment of the memorised speed while cruise control is in operation
You can adjust the memorised speed, displayed in zone A, by pressing on :
- button 4 to increase the speed,
- button 2 to decrease the speed.
Note : successive presses will modify the cruise speed in steps of 1 km/h and a sustained press in steps of 5 km/h (3 mph).
Temporary override of the cruise speed
During the operation of cruise con-trol, it is always possible to action the accelerator to go faster than the cruise speed (for example to over-take another vehicle). The speed displayed in zone A fl a s h e s .
You have only to release the ac-celerator pedal to return to the cruise speed.
C R U I S E C O N T R O L
Page 89 of 266
88
II
Stopping the function
- by an action on the control on position "REG" to position 0.
- by the engine stopping.
The cruise speed previously cho-sen is no longer memorised.
If there is a malfunction,a mes-sage will display accompanied by a sound signal and lighting of the SERVICE warning lamp.
Contact a CITROËN dealer.
Cruise control should only be used when the driving conditions allow you to drive at a constant speed.
D o n o t u s e i t i n h e a v y t r a f fi c , o r o n d a n g e r o u s o r s l i p p e r y r o a d s .
The driver must remain attentive and in full control of his vehicle.
You are recommended to keep your feet within range of the pe dals.
To avoid any risk of interfering with the pedals :
- c h e c k t h a t t h e fl o o r m a t i s c o r r e c t l y p o s i t i o n e d ,
- n e v e r u s e m o r e t h a n o n e fl o o r m a t .
Re-engaging cruise control
-by recall of the memorised speed :
After a disengagement, press on button 3. Your vehicle automati-cally returns to the memorised cruise speed which is displayed in zone A.
If the memorised cruise speed is higher than the current speed, the vehicle wll accelerate to reach the former.
- by selection of the current speed :
Press on button 2 or 4 once the desired speed has been reached.The information "OFF" will thendisappear from zone A.
Observation : If during the opera-tion of cruise control, the system is unable to keep within the memo-rised speed (for example on a steep d e s c e n t ) , t h e n t h e s p e e d fl a s h e s . Adapt your speed as necessary.
Disengaging of cruise control while retaining the memorised speed
- Either by pressing on the brake pedal or on the clutch pedal.
- Or by pressing button 3.
- Or if either the ESP or the ASR system is active.
Note : cruise control is not active if the gear lever is in neutral.
These actions cause the informa-tion "OFF" to appear in zone A of the instrument panel.
These manœuvres do not cancel the cruise speed which remains displayed in the instrument panel.
C R U I S E C O N T R O L
Page 90 of 266
1
3
4
2
A
II
89
This driving assistance device en-ables you to choose a maximum speed that you wish not to exceed. This has to be higher than 30 km/h (around 20 mph).
The speed limiter controls are lo-cated on the steering wheel.
Note : The information relating to the speed limiter is displayed in zone A of the instrument panel.
Selection of the function
Rotate the control 1 to the "LIM"position.
On selection of the function, the previous memorised speed and the information "OFF" are displayed :
A d j u s t m e n t o f t h e m a x i m u m speed
With the engine running, you can adjust the memorised maximum speed , by means of short or long presses on :
- button 4 to increase the memo-rised maximum speed,
- button 2 to decrease the memo-rised maximum speed.
Note : successive presses will modify the maximum speed in steps of 1 km/h and a sustained press in steps of 5 km/h (3 mph).
A c t i v a t i o n o f t h e m a x i m u m speed
When the desired maximum speed is displayed, press button 3 so that the limitation is activated.The information "OFF" thendis-appears from zone A.While the function is active, press-ing the accelerator pedal will not en-able the programmed speed to be exceeded, except if you press the pedal hard down to beyond the end-of-travel switch (see “Temporary override of the maximum speed”).
Note : The speed of your vehicle may vary slightly in relation to that memorised.
Bi-tone instrument panel
S P E E D L I M I T E R
Page 91 of 266
90
II
Stopping the function
- by an action on the control on position "LIM" to position 0.
- by the engine stopping.
The speed previously chosen is still memorised.
If there is a malfunction,a mes-sage will display accompanied by a sound signal and lighting of the SERVICE warning lamp.
Contact a CITROËN dealer.
Temporary override of the m a x i m u m s p e e d
The accelerator pedal is equipped with an end-of-travel switch. If you action this switch by pressing the pedal hard down, you can exceed the memorised maximum speed at any time.
During the time the speed is being exceeded, the displayed speed fl a s h e s .
You have only to release the ac-celerator pedal to return below the maximum speed and render the function active again.
Observation : If during the operation of the speed limiter, the system is unable to keep within the maximum speed (for example on a steep de-scent or under heavy acceleration) t h e n t h e s p e e d fl a s h e s . A d a p t y o u r speed as necessary.
The function will re-engage when your speed returns below the de-sired maximum speed.
Disengagement of the m a x i m u m s p e e d
Press on button 3.
This action causes the information "OFF" to appear on the instru-ment panel screen.
U s e o f fl o o r m a t s t h a t a r e n o t a p p r o v e d b y C I T R O Ë N m a y h i n d e r access to the accelerator pedal and thus interfere with the func-tioning of the speed limiter.
To avoid any risk of interfering with the pedals :
- c h e c k t h a t t h e fl o o r m a t i s c o r r e c t l y p o s i t i o n e d ,
- n e v e r u s e m o r e t h a n o n e fl o o r m a t .
This action does not cancel the memorised maximum speed which remains displayed in zone A ofthe instrument panel.
S P E E D L I M I T E R