2008 Citroen C4 PICASSO DAG Replace
[x] Cancel search: ReplacePage 70 of 266
B
C
DII
71
EMERGENCY UNLOCKING
In the event of the electronic parking brake malfunctioning o
r the battery running fl a t , a n e m e r g e n c y m a n u a l d e v i c e c a n u n l o c k t h e p a r k i n g b r a k e .
1. I m m o b i l i s e t h e v e h i c l e , w i t h t h e e n g i n e r u n n i n g , b y e n g a g i n g fi r s t g e a r ( m a n -ual gearbox), position P ( a u t o m a t i c g e a r b o x ) o r M or R ( 6 - s p e e d e l e c t r o n i c gearbox), then switch off the engine.
Note : if it is impossible to immobilise the vehicle, do not action the control and urgently contact a CITROËN dealer. if it is impossible to immobilise impossible to immobilise
2. F e t c h t h e v e h i c l e b l o c k s a n d t h e u n l o c k i n g d e v i c e ( b r a i d e d c a b l e ) f r o m t h e t o o l b o x ( s e e “ C h a n g i n g a w h e e l ” , p a r a g r a p h o n “ T o o l s ” ) .
3. Immobilise the vehicle by placing blocks at the front and at the rear of one of the rear wheels.
4. Slide the front left-hand seat back as far as possible.
5. L i f t u p t h e fl o o r p l u g B in the carpet under the seat.
6. Pierce the tab C on the tube D with the unlocking device.
7. Place the unlocking device in the tube D.
8. Turn the unlocking device clockwise. For safety reasons, it is essentialto continue turning the device as far as it will go or until you hear a knocking noise. The parking brake is released.
9. Remove the unlocking device and store it with the blocks in t he toolbox.
Note : - The operation of the parking brake re-initialises when the ignition is switched off then on again. If the reinitialisation of the parking brake proves impossible, contact a CITROËN dealer.off then on again. If the reinitialisation again. If
- The subsequent time required for application may be longer t han during normal operation.
For safety reasons, after this manoeuvre it is essential to contact a CITROËN dealer urgently to have the plug replaced.Following an emergency unlocking, immobilisation of the vehicle is no longer guaranteed once the manual emergency unlocking has been deployed and the manual control d oes not allow the re-application of your park-ing brake.Take no action, either on control A, or stopping starting the engine while the unlocking device is engaged.Take care not to allow moisture or dust in the proximity of the plug.
E L E C T R O N I C P A R K I N G B R A K E
E M E R G E N C Y U N L O C K I N G
Page 82 of 266
3
2
1
0
4
II
81
Windscreen wipe
3 Rapid wipe.
2 Normal wipe.
1 Intermittent wipe.
0 Stop.
4 Automatic wipe by pressing downwards, and single wipe.
Note : To deactivate automatic wipe :
- go to position 1, then return to position 0.
Position 1 : The wipe interval will adjust automatically depending on the speed of the vehicle.
Note : In position 2 or 3 : when the vehicle is stationary the wipe interval will reduce automatically.
F o r s a f e t y , t h e w i p e r s y s t e m i s d e a c t i v a t e d a p p r o x . o n e m i n u t e a f t e r you switch off the ignition.
When you switch on the ignition, to reactivate the function :
- return to the Stopposition,
- go to the position desired.
Vehicle equipped with a rain sensor
Position 4 by pressing downwards : The wipe interval will adjust auto-matically as a function of the intensity of the rain.
Note : A press downwards produces a single wipe without deactivating automatic wipe.
IMPORTANT :
Do not cover the rain sensor, which is located behind the interior rear view mirror and visible from outside the windscreen.
If washing the vehicle, switch off the ignition or deactiva te automatic wipe.
Changing the wiper blades
For replacement, the wipers should be stopped in themaintenance position.
Switch off the ignition, then within a minute action the wiper control stalk. The wipers will position themselves in the middle of the wi ndscreen.
After replacement, the wipers will resume their normal position when you switch on the ignition and action the wiper stalk.
For optimum wiping, change the wiper blades once they start t o leave marks on the screen ; otherwise, change them once or twice a year (e .g. in autumn and in spring).For safety, the wiper system is deactivated approx. one minute after you switch off the ignition.
W A S H / W I P E
Page 95 of 266
94
II
Proximity sensors are located in the front and rear bumpers of your vehicle.
Functioning
- When you engage reverse gear, a sound signal informs you that the system is active. The outline of your vehicle is displayed on the multi-function screen C or DT. Obstacles situated at the rear or in front of the vehicle will be detected.
- When you are moving forward, provided this is at a speed less than 10 km/h (approx. 6 mph), either in neutral or in gear, the outline on your vehicle is displayed on the screen as soon as an obstacle is dete cted in front of the vehicle. Obstacles located in front of the vehicle will be detected.
- In forward gear or in reverse gear, as the vehicle approaches the ob-stacle, the sound signal becomes more and more rapid and the ba rs are seen to move ever nearer to the vehicle.
- Whether in forward gear or in reverse gear, when theobstacle is close, the sound signal becomes continuous and the WARNING panel appears on the multifunction display.
Note : the sound signal is emitted by the loudspeakers that are nearest to the obstacle.
P A R K I N G A S S I S T A N C E
Multifunction screen DT
Multifunction screen C
This system can in no way replace vigilance and responsibility of the part of the driver.
When you engage reverse gear, a short sound signal followed by a different sound signal accompanied by a message and the lighting of the SERVICE warning lamp, indi cates that there is a malfunction.
Contact a CITROËN dealer.
Page 185 of 266
12
3
4
182
VIFRONT LENS
Dipped beam
Main beam
Sidelamp
Direction indicator
Note : A slight misting may appear on the internal sur-face of the headlamp glass in some climatic conditions (e.g. low temperature or humidity) ; this disappears af-ter the lamps have been on for a few minutes.
C H A N G I N G B U L B SH A L O G E N H E A D L A M P S
Dipped beam
1. Remove the rubber plug.
2. Rotate the bulb-holder a quarter turn anti-clockwise and remove it from its housing.
3. Replace the bulb H7.
4. Reposition the bulb-holder by pushing it in, tight e-ning it by a quarter turn (clockwise).
5. Put back the rubber plug.
Changing a halogen bulb should only be done after the headlamp has been switched off for a few minutes (risk of serious burns).
D o n o t t o u c h t h e b u l b d i r e c t l y w i t h y o u r fi n g e r s , u s e l i n t - f r e e c l o t h s .
It is imperative to use only anti-U.V. type bulbs in order not to damage the headlamp.
When using a high-pressure washer on persistant marks, do not direct at the lamps or their outlines for too long, so as not to damage their coating and their seals.
Page 186 of 266
VI
183
Main beam
1. Remove the rubber plug.
2. Detach the clips by lowering them on each side of the bulb.
3. Pull on t he bulb- holder t o remove it.
4. Replace the bulb H1.
5. Push the bulb-holder back into its housing.
6. Reattach the clips.
7. Put back the rubber plug.
Sidelamp
1. Rotate the bulb-holder a quarter turn anti-clockwise.
2. Remove it from its housing.
3. Replace the bulb H6W.
4. Reposition the bulb-holder.
5.Rotate it a quarter turn clock-wise to reposition in its housing.
Direction indicator
1. The direction indicator bulb is located underneath the main beam bulb. Remove the rub-ber plug.
2. Pull on the bulb-holder to re-move it.
3. Replace the bulb H21.
4. Reposition the bulb-holder in the bracket and push it in.
5. Put back the rubber plug.
C H A N G I N G B U L B SH A L O G E N H E A D L A M P S
Page 187 of 266
12
3
4
184
VI Main beam (H7)
1. Remove the rubber plug.
2. Rotate the bulb-holder a quarter turn anti-clockwise and remove it from its housing.
3. Replace the bulb H7.
4. Reposition the bulb-holder by pushing it in, tighte-ning it by a quarter turn (clockwise).
5. Put back the rubber plug.
FRONT LENS WITH XENON DUAL-FUNCTIONDIRECTIONAL HEADLAMPS
Xenon dual-function headlamp (dipped/main beam)
C H A N G I N G B U L B SX E N O N D U A L - F U N C T I O N H E A D L A M P S
If the headlamp bears this symbol, any operation to change the Xenon dual-function directional headlamp D1S is the preserve of professionals (risk of electrocution).
Contact a CITROËN dealer.
It is recommended to change both bulbs at the same time if one of them is faulty. Sidelamp (see “Halogen headlamps”)
Direction indicator (see “Halogen headlamps”)
When using a high-pressure washer on persistant marks, do not direct at the lamps or their outlines for too long, so as not to damage their coating and their seals.
Page 188 of 266
1
23
A
B
VI
185
REAR LENS
Note the bulb that is faulty.
Bulbs
Direction indicator: PY21W.
Stoplamp and sidelamp :P21/5W.
Reversing lamp : P21W.
Rear lamp units on the bodywork
1. With the tailgate open, press on the plastic cover A, located close to the lens, to release it from its housing.2. Undo the two screws B on the side of the lens and detach the lamp by pulling it rearwards.3.Disconnect the connector linking the lens unit with the tailgate.4. Remove the bulb-holder.5. Replace the bulbs. To remove a bulb, rotate it a quarter turn. To r e fi t t h e b u l b , r o t a t e i t a q u a r t e r turn in the other direction.6. Reposition the bulb-holder.7. Reconnect the connector to the lens unit.8. Reattach the lamp unit on the body work and do up the two screws.9. Reposition the plastic cover by exerting pressure.
Rear lamps on the tailgate
1. With the boot open, remove the plastic cover on the tailgate.
2. Remove the bulb-holder from its housing.
3. Replace the bulb. To remove a bulb, rotate it a quarter turn. To r e fi t t h e b u l b , r o t a t e i t a q u a r t e r turn in the other direction.
4. Reposition the bulb-holder.
5. R e fi t t h e p l a s t i c c o v e r .
C H A N G I N G B U L B S
R E A R L E N S - C 4 P I C A S S O
Page 189 of 266
3
2
1
4
186
VIREAR LENS
Note the bulb that is faulty.
Bulbs :
Direction indicator : PY21W.
Stoplamp : P21W.
Reversing lamp : P21W.
Sidelamp : LED
Contact a CITROËN dealer.
Rear lamps
1. With the tailgate open, undo the 3 screws located on the side of the lens unit and pull it rearwards to detach.
2. Disconnect the connector lin-king the lens unit to the boot. Do not disconnect the LEDs.
3. Remove the seal.
4. Remove the bulb-holder.
5. Replace the bulbs. To remove a bulb, rotate it a quarter turn. T o fi t t h e b u l b , r o t a t e i t a q u a r t e r turn in the other direction.
6. Reposition the bulb-holder.
7. Put back the seal.
8. Reconnect the connector to the lens unit.
9. Stow the harness in the opening provided in the bodywork.
10. Reattach the lens unit on the bodywork and do up the 3 screws.
Third stoplamp with bulb
1. With the boot open, detach the interior trim.
2. Undo the nuts.
3. Using a thin screwdriver, detach the 3 retaining lugs.
4. Remove the lamp via the exterior of the tailgate.
5. Remove the bulb-holder.
6. Change the faulty bulb(s).
Check that the vehicle lamps work correctly after each operation.
C H A N G I N G B U L B S
R E A R L E N S - G R A N D C 4 P I C A S S O
Third stoplamp with LED
Contact a CITROËN dealer