2008 Citroen C4 Position light
[x] Cancel search: Position lightPage 122 of 257
111
IX
D R I V I N G
Deactivation of cruise control with memorised speed
- E i t h e r b y p r e s s i n g t h e b r a k e p e d a l or the clutch pedal.
- O r w i t h a p r e s s o n b u t t o n 3.
- O r w h e n E S P o r A S R i s a c t i v e .
Note: cruise control is disengaged when the gear lever is in neutral position.
These actions bring up the display "OFF" in zone A in the instrument panel.
These actions do not cancel your cruise speed which remains displayed on the instrument panel.
Cruise control must only be used where road conditions permit driving at a constant speed.
Do not use it on congested roads or when weather and road conditions are poor.
The driver must still remain attentive and in complete control of the vehicle.
You are recommended to keep your feet within range of the pedals.To avoid any interference with the pedals:To avoid any To avoid any
- ensure that any over-mats are c o r r e c t l y fi t t e d ,
- never superimpose one over-mat on another.
Reactivation of cruise control
- by recalling the memorised speed:
Following a deactivation, press on button 3. Your vehicle automatically resumes the memorised cruise speed displayed in zone A.
- by selecting the current speed:
Press on button 2 or 4 as soon as the desired speed is reached. The information "OFF" will then disappear from zone A.
In the event of a malfunction, a message is displayed, accompanied by a sound signal and lighting of the S E R V I C E w a r n i n g l a m p .
C o n s u l t y o u r C I T R O Ë N d e a l e r .
To cancel the function
- b y m o v i n g t h e c o n t r o l f r o m p o s i t i o n "REG" to position 0.
- b y s t o p p i n g t h e e n g i n e .
T h e c r u i s e s p e e d c h o s e n p r e -viously is no longer memorised.
Page 123 of 257
1 1 2
IX
D R I V I N G
This driving assistance device allows you to select a maximum speed that you wish not to exceed. This has to b e a s p e e d g r e a t e r t h a n 3 0 k m / h ( a p p r o x . 2 0 m p h ) .
The speed limiter controls are located on the steering wheel.
Note: The information relating to the limiter is displayed in zone A of the instrument panel.
To select the function
Turn control 1 to position "LIM".
On selection of the function, the last speed memorised and the information "OFF" will appear:
To adjust the maximum speed
Provided the engine is running, you can adjust the memorised maximum speed, with short or long presses on:
- b u t t o n 4 to increase the memorised maximum speed,
- b u t t o n 2 to decrease the memorised maximum speed.
Note: successive presses modify the memorised speed in steps of 1 k m / h ( 1 m p h ) , a c o n t i n u o u s p r e s s i n s t e p s o f 5 k m / h ( 3 m p h ) .
Activation of the maximum speed
When the desired maximum speed is displayed, press button 3 to activate the limitation.
The information "OFF" then disappears from zone A.
While the function is active, pressing the accelerator pedal will not enable you to go beyond the programmed speed unless you press the pedal hard down past the tight spot (see "Temporary exceeding of the maximum speed").
Note: The vehicle speed may vary slightly from that memorised.
SPEED LIMITER
Page 124 of 257
1 1 3
IX
D R I V I N G
To stop the function
- m o v e t h e c o n t r o l f r o m p o s i t i o n "LIM" to position 0.
- o r s t o p t h e e n g i n e .
The speed that you chose is memorised.
In the event of a malfunction, a message is displayed, accompanied by a sound signal and lighting of the S E R V I C E w a r n i n g l a m p .
C o n s u l t y o u r C I T R O Ë N d e a l e r .
A fl o o r m a t n o t r e c o m -mended by CITROËN risks sliding under the accelerator pedal, thus preventing you from pressing past the tight spot.
It will then be impossible to exit from the desired limitation, unless by acting on the steering wheel control.
The driver must still remain attentive and in complete control of the vehicle.
We advise the driver to keep their feet close to the pedals.
Note: if during speed limitation, the system cannot keep to the maximum speed (especially on a steep descent or if you accelerate too hard) the s p e e d fl a s h e s . A d a p t y o u r s p e e d a s necessary.
T h e f u n c t i o n w i l l r e - e n g a g e w h e n your speed has returned below the desired maximum.
Deactivation of the maximum speed
Press button 3.
The information "OFF" will appear on the instrument panel screen.
This action does not cancel the memorised maximum speed, which remains displayed in zone A of the instrument panel.
Temporary override of the maximum speed
You can exceed the memorised maximum speed at any time by pressing the accelerator pedal hard down past the tight spot.
During the time the limit speed is being exceeded, the displayed s p e e d fl a s h e s .
You have only to release the accelerator pedal to return below the maximum speed, thus keeping the function active.
Page 133 of 257
122
X
M A I N T E N A N C E
Protection cover
HDi 135 and 140 engines
Remove the protection cover by fi r s t u n c l i p p i n g p o i n t 1, then 3 and4 . D e t a c h p o i n t 2 by pulling towards you, then lift.
To reposition the protection cover, attach point 2 fi r s t . L o w e r t h e c o v e r , keeping it centred. Clip points 1 and4, pushing vertically and slightly rearwards. Clip point 3 pushing down vertically.
HDi engines are of a highly technical nature.
A l l m a i n t e n a n c e a n d r e p a i r s r e q u i r e s p e c i fi c q u a l i fi c a t i o n s which only your CITROËN Dealer can guarantee. A l l m a i n t e n a n c e a n d r e p a i r s r e q u i r e s p e c i fi c q u a l i fi c a t i o n s A l l m a i n t e n a n c e a n d r e p a i r s r e q u i r e s p e c i fi c q u a l i fi c a t i o n s
Bleeding of water from the diesel f u e l fi l t e r
To be bled on a regular basis (at every oil change).
To evacuate the water, slacken the bleed screw or the water in diesel fuel sensor, which is located at the b a s e o f t h e fi l t e r , u n t i l w a t e r c e a s e s t o fl o w o u t .
Then retighten the bleed screw or the water in diesel fuel sensor.
DIESEL INJECTION EQUIPMENTWear of brake discs, brake pads and brake drums
The rate of wear of the brake pads depends on the use of your vehicle (urban use, frequent stops), and on your style of driving or the type of journey.
For information on checking the discs and drums for wear, contact a CITROËN dealer.
After washing the vehicle, brake progressively to dry out the brake linings.
Page 134 of 257
122
X
M A I N T E N A N C E
Protection cover
HDi 135 and 140 engines
Remove the protection cover by fi r s t u n c l i p p i n g p o i n t 1, then 3 and4 . D e t a c h p o i n t 2 by pulling towards you, then lift.
To reposition the protection cover, attach point 2 fi r s t . L o w e r t h e c o v e r , keeping it centred. Clip points 1 and4, pushing vertically and slightly rearwards. Clip point 3 pushing down vertically.
HDi engines are of a highly technical nature.
A l l m a i n t e n a n c e a n d r e p a i r s r e q u i r e s p e c i fi c q u a l i fi c a t i o n s which only your CITROËN Dealer can guarantee. A l l m a i n t e n a n c e a n d r e p a i r s r e q u i r e s p e c i fi c q u a l i fi c a t i o n s A l l m a i n t e n a n c e a n d r e p a i r s r e q u i r e s p e c i fi c q u a l i fi c a t i o n s
Bleeding of water from the diesel f u e l fi l t e r
To be bled on a regular basis (at every oil change).
To evacuate the water, slacken the bleed screw or the water in diesel fuel sensor, which is located at the b a s e o f t h e fi l t e r , u n t i l w a t e r c e a s e s t o fl o w o u t .
Then retighten the bleed screw or the water in diesel fuel sensor.
DIESEL INJECTION EQUIPMENTWear of brake discs, brake pads and brake drums
The rate of wear of the brake pads depends on the use of your vehicle (urban use, frequent stops), and on your style of driving or the type of journey.
For information on checking the discs and drums for wear, contact a CITROËN dealer.
After washing the vehicle, brake progressively to dry out the brake linings.