2008 Citroen C4 DAG ignition
[x] Cancel search: ignitionPage 105 of 257
98
IX
D R I V I N G
Manual gearbox
- Ensure that the gear lever is in the neutral position.
- Do not touch the accelerator.
- In the case of diesel engine vehi-cles: turn the key to the drive position. Wait for the pre-heater warning lamp to go off, if it is on.
- Action the starter by turning the key until the engine starts (but not for more than ten seconds).
- In temperatures lower than 0 °C, apply the clutch during the action on the starter in order to aid starting. Then release the clutch slowly.
DO NOT RUN THE ENGINE IN A SPACE THAT IS ENCLOSED OR INSUFFICIENTLY VENTILATED.
Automatic gearbox
- Check that you are in position P or N.
- Do not touch the accelerator.
- For Diesel engines: turn the key to position M. Wait for the pre-heater warning lamp to go off if it is on.
- Action the starter by turning the key until the engine turns over (not for longer than ten seconds).
Advice
Vehicles equipped with a Turbo:
Turbo equipped engines MUST be allowed to return to idle for several seconds before switching off the ignition. Failure to do so could cause serious damage to the turbo unit.
Flicking the throttle pedal as the ignition is turned off can lead to severe dam-age to the turbo unit.
(6 speed) Electronic Gearbox System
- Check that you are in position N.
- Fully depress the brake pedal.
- Do not touch the accelerator.
- For Diesel engines: turn the key to position M. Wait for the pre-heater warning lamp to go off if it is on.
- Action the starter by turning the key until the engine turns over (not for longer than ten seconds).
Note: If the vehicle has been sta-tionary for a long time, or if you have pressed the brake pedal a number of times while stationary, it will be necessary to press the brake pedal hard down in order to authorise the engine to start.
STARTING
Page 106 of 257
98
IX
D R I V I N G
Manual gearbox
- Ensure that the gear lever is in the neutral position.
- Do not touch the accelerator.
- In the case of diesel engine vehi-cles: turn the key to the drive position. Wait for the pre-heater warning lamp to go off, if it is on.
- Action the starter by turning the key until the engine starts (but not for more than ten seconds).
- In temperatures lower than 0 °C, apply the clutch during the action on the starter in order to aid starting. Then release the clutch slowly.
DO NOT RUN THE ENGINE IN A SPACE THAT IS ENCLOSED OR INSUFFICIENTLY VENTILATED.
Automatic gearbox
- Check that you are in position P or N.
- Do not touch the accelerator.
- For Diesel engines: turn the key to position M. Wait for the pre-heater warning lamp to go off if it is on.
- Action the starter by turning the key until the engine turns over (not for longer than ten seconds).
Advice
Vehicles equipped with a Turbo:
Turbo equipped engines MUST be allowed to return to idle for several seconds before switching off the ignition. Failure to do so could cause serious damage to the turbo unit.
Flicking the throttle pedal as the ignition is turned off can lead to severe dam-age to the turbo unit.
(6 speed) Electronic Gearbox System
- Check that you are in position N.
- Fully depress the brake pedal.
- Do not touch the accelerator.
- For Diesel engines: turn the key to position M. Wait for the pre-heater warning lamp to go off if it is on.
- Action the starter by turning the key until the engine turns over (not for longer than ten seconds).
Note: If the vehicle has been sta-tionary for a long time, or if you have pressed the brake pedal a number of times while stationary, it will be necessary to press the brake pedal hard down in order to authorise the engine to start.
STARTING
Page 108 of 257
98
IX
D R I V I N G
Manual gearbox
- Ensure that the gear lever is in the neutral position.
- Do not touch the accelerator.
- In the case of diesel engine vehi-cles: turn the key to the drive position. Wait for the pre-heater warning lamp to go off, if it is on.
- Action the starter by turning the key until the engine starts (but not for more than ten seconds).
- In temperatures lower than 0 °C, apply the clutch during the action on the starter in order to aid starting. Then release the clutch slowly.
DO NOT RUN THE ENGINE IN A SPACE THAT IS ENCLOSED OR INSUFFICIENTLY VENTILATED.
Automatic gearbox
- Check that you are in position P or N.
- Do not touch the accelerator.
- For Diesel engines: turn the key to position M. Wait for the pre-heater warning lamp to go off if it is on.
- Action the starter by turning the key until the engine turns over (not for longer than ten seconds).
Advice
Vehicles equipped with a Turbo:
Turbo equipped engines MUST be allowed to return to idle for several seconds before switching off the ignition. Failure to do so could cause serious damage to the turbo unit.
Flicking the throttle pedal as the ignition is turned off can lead to severe dam-age to the turbo unit.
(6 speed) Electronic Gearbox System
- Check that you are in position N.
- Fully depress the brake pedal.
- Do not touch the accelerator.
- For Diesel engines: turn the key to position M. Wait for the pre-heater warning lamp to go off if it is on.
- Action the starter by turning the key until the engine turns over (not for longer than ten seconds).
Note: If the vehicle has been sta-tionary for a long time, or if you have pressed the brake pedal a number of times while stationary, it will be necessary to press the brake pedal hard down in order to authorise the engine to start.
STARTING
Page 111 of 257
101
IX
D R I V I N G
Neutral
If the vehicle is moving, do not select this position, even momentarily.
Reverse gear
Only engage reverse gear when the vehicle is stationary.
If the vehicle is moving at a very low speed, if reverse gear is requested (position R) this will be taken into account only when the vehicle comes to a halt.
The "foot on brake" warning lamp m a y fl a s h i n t h e i n s t r u m e n t p a n e l to remind you to brake.
If the vehicle is moving at a high speed, if reverse gear is requested the warning lamp "N" w i l l fl a s h a n d your vehicle will go automatically into neutral. To re-engage a gear, you have only to return the gear lever to position A or M.
A sound signal indicates when reverse gear is engaged.
If parking assistance is deacti-vated, the sound signal for reverse gear engaged is absent.
The engine can only be started if the brake pedal is pressed and the gear lever is in position N.
The warning lamp "foot on b r a k e " fl a s h e s o n t h e d i s p l a y .
With the engine running, before accelerating away check the position engaged by looking at the lever grille or the rev counter : R, A or M.
If you are stationary with the engine running, take care to leave your gear selector in position N.
Sport option
Activation
Press on button S, situated on the lever grille.
The warning lamp "S" displays on the rev counter.
This option can be activated either in automatic mode or in manual mode.
Deactivation
Press again again on button S on the lever grille.
The warning lamp "S" disappears on the rev counter.
Note: the Sport option is deacti-vated whenever you switch off the ignition.
Automatic mode
Manual mode
- Push the lever to change to a higher gear.
- Pull the lever to change to a lower gear.
Page 130 of 257
119
X
M A I N T E N A N C E
A i r fi l t e r
Follow the recommendations in the Maintenance Guide.
When working under the bonnet, when the engine is hot (even stopped and the ignition switched off), the cooling fan coul d operate at any time.
Check the engine oil level frequently between routine service visits, as well as prior to long journeys.
Engine coolant
The coolant level should be between the MAX and MINmarks on the header tank.
If the engine is hot, wait 15 minutes.
Quality: See "Maintenance Guide"
Never work on the cooling system if the engine is hot.
12 volt battery
See "Practical advice".
Engine oil
Check the oil level with the vehicle parked on level ground, after the engine has been switched off for at least fi f t e e n m i n u t e s .
Quality: See "Maintenance Guide"
B r a k e fl u i d
T h e fl u i d l e v e l m u s t b e s i t u -ated within the MAX and MIN marks visible on the reservoir.
T h e s c r e e n w a s h fl u i d s h o u l d b e replaced periodically as it loses its effectiveness over time.
Quality: See "Maintenance Guide"
If the warning lamp comes on while you are driving, stop immediately and contact the CITROËN network.you are driving, stop immediately stop immediately
D u s t fi l t e r / o d o u r fi l t e r (active carbon)
See "Maintenance Guide"
Take out the oil dipstick.
The level must be between the MAX and MIN marks on the dipstick
It should never exceed the maximum mark.
Windscreen, rear screen and headlamp washer fl u i d
It is recommended that you use products approved by CITROËN.It is recommended that you hat you
S c r e e n w a s h fl u i d r e s e r v o i r : 3.5 litres.
Screen and headlamp wash res-ervoir: 6.5 litres.
S p e c i fi c a t i o n f o r t h e fl u i d
To ensure optimum cleaning and to a v o i d f r e e z i n g , t o p p i n g u p o r fi l l i n g of the reservoir must not be done with just water.
MAX
MIN
LEVELS
Page 132 of 257
121
X
M A I N T E N A N C E
Windscreen and rear screen w a s h e r fl u i d
For best results as well as for your safety, use only CITROËN approved For best results as well as for your as well as
products which protect at tempera-tures as low as -25 °C to -30 °C.
I t i s e s s e n t i a l t o h a v e s u f fi c i e n t s c r e e n w a s h fl u i d i f y o u r v e h i c l e i s equipped with Xenon headlamps.
T o c h e c k t h e l e v e l , p l a c e a fi n g e r on aperture A before removing the cap.
Capacity: 3.5 litres.
Capacity with headlamp washers: 6.5 litres.
B r a k e fl u i d
T h e s y n t h e t i c fl u i d n o t o n l y g i v e s protection against corrosion but also ensures correct functioning of the braking system in all environmental conditions, therefore you should only use the synthetic product recom-mended by the CITROËN network. use the synthetic product recom-product
( t h i s fl u i d m u s t b e r e p l a c e d e v e r y two years).
These important requirements are detailed in your vehicle’s Mainte-nance Guide.
Quality: See "Maintenance Guide".
When working under the bonnet, when the engine is hot (even stopped and the ignition switched off), the cooling fan coul d operate at any time.
B r a k e fl u i d r e s e r v o i r
Check and top up at regular intervals.
T h e fl u i d l e v e l m u s t b e s i t u a t e d w i t h i n the max and min marks visible on the reservoir.
If the warning lamp comes on when driving, stop as quickly as possible and contact a CITROËN dealer.driving, stop as quickly as possible quickly
Page 158 of 257
146
XI
P R A C T I C A L A D V I C E
Towing with all wheels on the ground
T o w i n g r i n g fi x i n g s a r e p l a c e d a t t h e f r o n t a n d a t t h e r e a r o f t h e v e h i c l e .
T o a c c e s s t h e m :
- a t t h e f r o n t : p u s h o n t h e l e f t t o t i l t t h e c o v e r , t h e n r e m o v e i t .
- a t t h e r e a r : p u s h a t b o t t o m , t h e n p u l l o n t o p .
T h e c o v e r r e m a i n s a t t a c h e d t o t h e b u m p e r b y m e a n s o f a t a b , s o t h a t i t c a n n o t b e c o m e l o s t .
The ignition key should be in position "M" so as to retain steering.
U s e a b a r w i t h h o o k s t o a t t a c h o n t h e t o w i n g r i n g s .
Vehicles with manual transmission
F o r v e h i c l e s w i t h m a n u a l t r a n s m i s s i o n , t h e g e a r l e v e r m u s t b e i n n e u t r a l . F a i l u r e t o o b s e r v e t h i s r e q u i r e m e n t c a n l e a d t o t h e f a i l u r e o f c e r t a i n b r a k i n g c o m p o - n e n t s a n d a l a c k o f b r a k i n g a s s i s t a n c e o n r e s t a r t i n g t h e e n g i n e .
If the engine is not running, the steering and braking systems will not be power-assisted.
If towing another vehicle, the latter should be free-wheeling (that is, gearbox in neutral).
Page 178 of 257
166
XIII
A U D I O
AUDIO SETTINGS
On/Off
With the key in Drive position M, press on control A to switch the radio on or off.
Note:
- If the radio was on the last time you switched off the ignition, it will resume automatically when you switch on the ignition again. You will not have to press on control A.
- After switching off the ignition, you can still operate the audio system even without the ignition key being present. Simply press on button A. The system will turn itself off after approx. 30 minutes.
Anti-theft system
This radio is coded in such a way as to function only on your particular vehicle. It would be unusable if installed on any other vehicle.
Note:
The anti-theft system is automatic and requires no action on your part.
Selection of source
To select either Radio, CD (CD already inserted and Radio source activated), or CD changer source, press on control D.
When you insert a CD it automatically starts being read.
Note:
When the radio is switched off, the source selected is memorised.
Volume adjustment
Rotate control A to increase or decrease the sound volume.
You can also increase or decrease the volume using buttons 1 and 4 at the steering wheel.
Note:
- The sound volume when you switch off the radio will be the same when you switch it on again.
- The radio sound volume automatically adjusts to the vehicle speed, provided the "volume adjustment" function is activated.
Temporary sound pause
Press on control 5 at the steering wheel to activate this function.
The sound will be paused, regardless of the source selected.
To restore the audio output, press one of the controls at the steering wheel.
Sound adjustments
Each press on button F brings up the parameter to be adjusted: choice of p r e d e fi n e d s o u n d a m b i a n c e s , b a s s , treble, loudness, fade (front/rear sound distribution), balance (left/right sound distribution) and volume adjusted to vehicle speed.
Press buttons K or N to modify the values for the function displayed.
Note:
- The selection of a sound ambiance automatically adjusts bass and t r e b l e . T h e s e c a n b e m o d i fi e d .
To restore the original adjustments for the musical ambiances, reset bass and treble to zero.
- Adjustment of loudness, as well as bass and treble when they are a v a i l a b l e , a r e s p e c i fi c t o e a c h sound source and to each musical ambiance.
- If you leave the audio system un-actioned for a few seconds, it will revert to the normal display.