2008 Citroen C CROSSER warning lights

S A F E T Y
100
BRAKING ASSISTANCE
SYSTEMS
Group of supplementary systems which
help you to obtain optimum braking
in complete safety in emergency
situations:
- the anti-lock braking system (ABS),
- the electronic brake force distribution (EBFD).
When braking in an emergen-
cy, press very fi rmly without re-
leasing the pressure. The two warning lights comes on at
the same time and the two warnings
are displayed alternately on the
instrument panel display.
When replacing wheels (tyres and
rims), ensure that they conform to the
manufacturer’s recommendations.
Operating fault
If this warning light comes on,
accompanied by the indication on the
instrument panel display, it indicates
a malfunction of the anti-lock braking
system which could result in a loss of
control of the vehicle when braking.
Consult a CITROËN dealer.
If these two warning lights come
on, linked with the warnings on the
instrument panel display, they indicate a
malfunction of the electronic brake force
distribution which could result in a loss of
control of the vehicle on braking.

You MUST stop as soon as it is safe
to do so.
Consult a CITROËN dealer.
Anti-lock braking system
and electronic brake force
distribution
Linked systems which improve the sta-
bility and manoeuvrability of your vehi-
cle when braking, in particular on poor
or slippery surfaces. The warning light comes on for a few
seconds when the ignition is switched
on (ON position). If it does not switch
off or does not come on, contact a
CITROËN dealer.
When the vehicle is stationary
When the vehicle is moving
If this warning light comes
on continuously it indicates
a malfunction of the anti-lock
braking system which could
result in a loss of control of the vehicle
on braking.

You MUST stop as soon as it is safe
to do so.
Consult a CITROËN dealer.
Activation
The anti-lock braking system is active if
the vehicle speed is higher than 6 mph
(10 km/h). It is deactivated when the ve-
hicle speed falls below 3 mph (5 km/h).
The anti-lock braking system comes
into operation automatically when there
is a risk of wheel lock.
Normal operation of the ABS may make
itself felt by slight vibration of the brake
pedal.

P R A C T I C A L I N F O R M A T I O N
IX
129
CHANGING A BULB
Handle the bulbs using a dry
cloth.

Do not clean the headlamps
using a dry or abrasive cloth, or us-
ing detergent or solvent products,

use a sponge and soapy water. In certain climatic conditions
(low temperature, humidity),
t
he
presence of condensation on the
inside of the headlamp glass is
normal ; it disappears a few minutes
after the lights are switched on.
Front lights
Blown bulb
Refer to the appropriate procedure to
change the corresponding bulb.
1. Direction indicators
(PY21W - 21 W).
2. Dipped headlamps (H11 - 55 W) or xenon bulb (D2S - 35 W).
3. Side lights (W5W - 5 W).
4. Main beam headlamps (H7 - 55 W).
5. Front fog lamps (H11 - 55 W). WARNING: RISK OF
ELECTROCUTION
Xenon bulbs must be replaced by a
CITROËN dealer.
Operating procedure for replacing a
faulty bulb with a new bulb.

P R A C T I C A L I N F O R M A T I O N
IX
146
TOWING
Access to the tools Having your vehicle towed on a
flatbed

 Below the front bumper, install the
towing system on the towing eye 1 .
 On the rear bumper, remove the
cover by pulling at the bottom using
the jack handle 2 .
Towing another vehicle
The towing eye and the tools are stored
in the storage compartment in the right-
hand boot trim.
To access them:

 open the boot,

 turn button A to the left,

 remove the cover B ,

 remove the fi xing band C and take
out the tool bag
D containing the
tools,

 take the towing eye and the tools
required out of the tool bag.
When being towed with the
engine off, there is no longer any
braking or steering assistance.
Place the gear lever in neutral.

Always have the vehicle
towed on a fl atbed.
Never have the vehicle towed
with the four wheels on the ground,
this could damage the transmission.
The vehicle must not be towed with
the front or rear wheels on the ground
even if it is in front “2WD” (2 wheel
drive) mode.
 Screw in the towing eye fully using
the wheelbrace 3 .

 Install the towbar.

 Switch on the hazard warning lights
on the towed vehicle.
Operating procedure for having your
vehicle towed on a fl atbed or for towing
another vehicle using a removable
mechanical device.