2008 Citroen C CROSSER ECO mode

C O M F O R T
II
46
Air conditioning On / Off (5)

 Press button 5 to activate the air
conditioning.
The indicator light comes on.
Intake of exterior air / Recirculation of interior air (4)

This function insulates the passenger
compartment from exterior odours and
smoke.

 Press button 4 to select the air in-
take mode.
When the indicator light on button 4 is
off, the exterior air intake function is ac-
tivated.
When the indicator light on button 4 is
on, the intake of exterior air is deacti-
vated and the system is in air recircula-
tion mode.
Do not drive for long periods in in-
terior air recirculation mode, except
in truly exceptional atmospheric
conditions. Personalisation of the Exterior air
intake / Interior air recirculation
function
This function is controlled automati-
cally. However, you can deactivate its
automatic control if you wish to change
the air intake mode at any time.
Personalisation of the Air
Conditioning On / Off function
This function is controlled automati-
cally. However, you can deactivate its
automatic control if you wish to activate
or deactivate the air conditioning at any
time.
The settings are retained, even after
switching off the ignition.
Changing the status
Press the Air Conditioning On / Off but-
ton for at least 10 seconds.
When the status changes from active to
inactive, three bleeps are heard and the
indicator light fl ashes three times.
When the status changes from inactive
to active, two bleeps are heard and the
indicator light fl ashes three times.
Automatic control active
If the air distribution adjustment dial and
the air fl ow adjustment dial are placed
in the “AUTO” position, or if the temper-
ature control dial is set to the minimum
temperature, the air conditioning sys-
tem is controlled automatically.
Automatic control active
If the air distribution adjustment dial
and the air fl ow adjustment dial are
placed in the “AUTO” position, the Air
intake / Interior air recirculation func-
tion is also controlled automatically.
Changing the status
Press the Air intake / Interior air recircu-
lation button for at least 10 seconds.
When the status changes from active to
inactive, three bleeps are heard and the
indicator light fl ashes three times.
When the status changes from inactive
to active, two bleeps are heard and the
indicator light fl ashes three times.
Automatic control inactive
Even if the air distribution adjustment
dial and the air fl ow adjustment dial are
placed in the “AUTO” position, the Air
intake / Interior air recirculation function
is no longer controlled automatically.
Automatic control inactive
The air conditioning system is no
longer controlled automatically.

A C C E S S
III
76
The electric window switches can
be confi gured via the colour display
“Equipment” menu.
The electric window switches remain
operational for approximately
30 seconds after the ignition is
switched off and the switch on the
driver’s door remains operational for
a further 30 seconds when the door
is opened.
The windows can no longer be
opened or closed after the driver’s
door is closed.
The rear windows do not lower fully.
ELECTRIC WINDOWS
1. Driver’s electric window switch.
2. Passenger’s electric window switch.
3. Rear left electric window switch.
4.
Rear right electric window switch.
5. Disarming of the passenger and rear electric window switches. In the event of unwanted opening of
the window on closing (for example
in the presence of frost), reinitialise
the electric windows (refer to the cor-
responding paragraph).
Safety auto-reverse
In automatic mode, when the window
rises and meets an obstacle, it stops
and lowers again.
Operation
With the ignition on, you have two op-
tions:
-
manual mode

 Press the switch gently to open or
pull it gently to close. The window
stops as soon as the switch is re-
leased.
- automatic mode

 Press the switch fully to open or
pull it fully to close. The window
opens or closes completely when
the switch is released.

 Pressing the switch again stops
the movement of the window.
System which opens or closes a win-
dow manually or automatically. It is fi t-
ted with a system which provides pro-
tection if an obstacle is detected on
one-touch models and a deactivation
system to prevent misuse of the rear
controls.

A C C E S S
III
82
Safety auto-reverse and
reinitialisation
If the roof meets an obstacle while it is
closing, it stops and opens again. Always remove the key from
the ignition when leaving the
vehicle, even for a short time.
If the roof meets an obstacle dur-
ing operation, you must reverse the
movement of the roof. To do this,
press the control concerned.
When the driver operates the roof
control, he must ensure that no one
is preventing the roof from closing
correctly.
The driver must ensure that passen-
gers use the sunroof correctly.
Be aware of children when operating
the roof.
In the event of unwanted opening of
the roof on closing (for example, in
the presence of ice) and immediately
after the roof has stopped, or after
the safety auto-reverse has been
triggered fi ve times in succession:

 press part 3 of the control several
times to partially open the roof,

 when the roof partially opens,
continue to press for more than
3 seconds .

 open and close the sunroof com-
pletely.

The safety auto-reverse function
is not operational during t hese
operations. SHUTTER
The shutter is manual, slide it.
It is stored automatically when the roof
is opened.
Check that the sunroof is
not open in tilt mode before
closing the shutter.
The shutter cannot be closed
when the sunroof is open in sliding
mode .

V I S I B I L I T Y
IV
89

A. rear wiper selection ring:
park
intermittent wipe
wipe with screen wash
Rear wiper
The wiper wipes twice then switches to
intermittent mode with an interval of a
few seconds.
Keep the ring in this position to operate
the screen wash with several wipes of
the wiper. The intermittence of the rear wiper
can be confi gured via the colour
display “Equipment” menu.

D R I V I N G
VII
112
FOUR WHEEL DRIVE SYSTEM
WITH ELECTRONIC CONTROL
4WD AUTO (position 1)
The vehicle operates with four wheel
drive and provides optimum traction
regardless of the level of grip.
This is the vehicle’s normal and regular
operating mode, the distribution of the
torque between the front and rear axles
is controlled automatically.
The distribution favours the front wheels,
the transfer of torque to the rear wheels
is managed electronically by the control
unit in relation to the level of grip, so
guaranteeing optimum road holding.
Three transmission modes are
available and can be selected manually
by the driver in accordance with his
requirements.
You can change transmission mode
when stationary or while driving at a
speed below 60 mph (100 km/h) .
The transmission mode can be selected
by turning the control A . Display on the instrument panel
The transmission mode is displayed in
the form of an intermittent display on
the instrument panel display when the
transmission mode is selected.
Selecting the transmission
mode
The selection of this mode is rec-
ommended when the level of grip
permits.
2WD (position 3)
The vehicle operates with front two
wheel drive.
This mode corresponds to use on a
tarmacked road on which the driver
considers that there is no risk of loss of
grip (dry road).
4WD LOCK (position 2)
The vehicle operates with four wheel
drive in this mode also.
It is recommended when grip is particularly
poor or diffi cult (sand, mud, slopes, etc.).
System which permits the selection of
a transmission mode in relation to the
driving conditions.

A U D I O E Q U I P M E N T a n d T E L E M A T I C S
XI
154
YOUR AUDIO-CD SYSTEM

This consists of the following
components:
- a control panel,
- a multifunction display,
- steering wheel audio controls,
- 4 or 6 speakers (according to version),
- a CD changer (according to version),
- auxiliary sockets, located at the rear of the centre console (according to
version),
- a radio aerial, located on the roof at the rear of the vehicle. Steering wheel audio controls

1.
On / Off and selection of the
radio or CD mode

2.
Decreasing of the volume

3.
Increasing of the volume

4.
Search for a higher radio
frequency / Next track / Fast
forwards play

5
.
Search for a lower radio frequency / Previous track / Rewind play
They can be used when the ignition
switch is in the “ON” or “ACC” position.
Switching on
Press button 1 for more than two
seconds.
The last source selected before switching
off comes back into operation.
Selecting the source
Press button 1 .
The source changes in the following
order: FM1 / FM2 / FM3 / MW / LW /
CD / FM1...
Searching in radio mode
Press button 4 or
5 to search for a higher
or lower radio frequency respectively.
While a track is being played,
press button 5 once to return to the
beginning of this track.
Adjusting the volume
Press and hold button
2 or
3 to decrease
or increase the volume respectively.

It allows you to:
- listen to the radio in FM/MW/LW,
- listen to audio CDs (CD-DA, CD- Text, CD-R/RW) or CDs with MP3
fi les. Switching off
Press button 1 for more than two
seconds. Searching in CD mode
Press button
4 or
5 to select the next or
previous track on the CD respectively.
Press and hold button 4 or 5 for fast
forwards or rewind playing of the current
track of the CD respectively.

A U D I O E Q U I P M E N T a n d T E L E M A T I C S
XI
157
GENERAL FUNCTIONS
Switching on Press the “PWR” button.
The last source selected
before switching off resumes
operation.
The audio equipment functions can be
used when the ignition switch is in the
“ON or “ACC” position.
Adjusting the volume Turn the “VOL” dial
respectively to the left to
decrease the volume or to
the right to increase it.
Switching off
Press the “PWR” button again. Setting the audio modes
Press the “SOUND” button
several times; the audio
modes change in the
following order:
SUB PUNCH / TYPE /
FIELD / BASS / MID /
TREBLE / FADER / BALANCE / OFF.
Quick access mode
To access the personalised sound
functions quickly, press and hold
this button, then turn it to reach the
personalised sound setting of your
choice.
Release the button to store the setting.
“Hold” mode
If you press this button for more than
2 seconds in the audio setting mode, the
system switches to “Hold” mode. The
audio mode selected will be retained
until you press this button again for
more than 2 seconds. Selecting the musical ambience
“TYPE”
Turn the “SOUND” dial; the
musical ambiences change
in the following order:
CLASSIC / JAZZ / POP /
ROCK / HIP-HOP.
Once the ambience has
been selected, press the “SOUND” but-
ton to confi rm.
“CLASSIC”: optimises the acoustics to
obtain perfect equalisation of the sound
for classical music.
“JAZZ”: optimises the acoustics to
obtain an ambient sound with speciifc
modulations in the bass, mid tone and
treble for jazz.
“POP”: optimises the acoustics to obtain
clear vocals and modulation of the bass
and treble for pop music.
“ROCK”: optimises the acoustics to
obtain a sound in harmony with the
rhythm which places the emphasis on
the mid tone for rock music.
“HIP-HOP”: optimises the acoustics
to obtain a powerful sound and
accentuation of the bass for hip-hop
music.
If the “TYPE” is changed, the sound
cuts out briefl y.
The audio setting mode is deactivated
when the radio is operated or a CD
is played or after approximately
10 seconds without any action.

A U D I O E Q U I P M E N T a n d T E L E M A T I C S
XI
158
Selecting the surround effect
“FIELD” Turn the “SOUND” dial; the
surround effects change in
the following order:
NORMAL / STAGE / LIVE /
HALL.
“NORMAL”: produces a sound in which
the voices are at the front and the in-
struments surround the listener.
“STAGE”: produces a sound in which
the voices are immediately facing the
listener, as on a stage.
“LIVE”: produces a sound similar to
that of a live show, in which the sound
reaches the listener from all directions.
“HALL”: produces a sound similar to
that of a concert hall with defl ection of
the sound. Setting the bass “BASS”
Turn the “SOUND” dial to
set the required bass value.
Setting the mid tone “MID”
Turn the “SOUND” dial to set the
required mid tone value.
Setting the treble “TREBLE”
Turn the “SOUND” dial to set the
required treble value.
Setting the front/rear sound
distribution “FADER”
Turn the “SOUND” dial to set the
balance of the volume of the front and
rear speakers.
Setting the right/left sound
distribution “BALANCE”
Turn the “SOUND” dial to set the
balance of the volume of the right and
left speakers.
If the “FIELD” is changed, the sound
cuts out briefl y. If the value “0” is set, an audible
signal will be heard. Automatic volume adjustment
“SCV”
This permits automatic adjustment of
the “VOLUME”, “BASS”, “MID” and
“TREBLE” parameters in relation to the
vehicle speed.
Press the “SOUND” button
for more than two seconds to
gain access to the functions
setting mode.
Then, press this same
button several times; the
functions setting mode changes in the
following order:
AF / CT / REG / TP-S / PTY (languages) /
SCV / PHONE / OFF.
Turn the “SOUND” dial respectively to
the left to deactivate the function or to
the right to activate it. If the “SUB PUNCH” is changed, the
sound cuts out briefl y.
Setting the volume of the bass
box “SUB PUNCH”
Turn the “SOUND” dial to set the volume
of the bass box.
Only vehicles fi tted with the “Premium
Sound” system can offer the “SUB
PUNCH” setting.
Once the surround effect has been se-
lected, press the “SOUND” button to
confi rm.