2008 CHRYSLER 300 SRT park assist

“Park Assist System”
When ON is selected, the system will scan for objects
behind the vehicle when the transmission is in the
REVERSE or NEUTRAL position. To make your selec-
tion, press and release the FUNCTION SELECT button
until “ON” or “OFF” appears.
“Turn-by-Turn Navigation” — If Equipped
When ON is selected, the turn-by-turn directions will
appear in the display as the vehicle approaches a desig-
nated turn within a programmed route. To make your
selection, press and release the FUNCTION SELECT
button until “ON” or “OFF” appears.
“Display Units of Measure in”
The EVIC, odometer, and navigation system (if
equipped) can be changed between English and Metric
units of measure. To make your selection, press and
release the FUNCTION SELECT button until “US” or
“METRIC” appears.
“Automatic High Beams” — If Equipped
When this feature is selected, the high beam headlights
will deactivate automatically under certain conditions. To
make your selection, press and release the FUNCTION
SELECT button until “ON” or “OFF” appears. Refer to
“SmartBeams” in Section 3.
230 UNDERSTANDING YOUR INSTRUMENT PANEL

▫Traction............................312

Driving Through Water..................313
▫Flowing/Rising Water..................313
▫Shallow Standing Water.................313

Parking Brake.........................315

Brake System..........................317
▫Anti-Lock Brake System................317

Power Steering........................319

Electronic Brake Control System............320
▫ABS (Anti-Lock Brake System)............321
▫TCS (Traction Control System)............322
▫BAS (Brake Assist System)...............322
▫ESP (Electronic Stability Program).........323▫Synchronizing ESP....................326
▫ESP/BAS Malfunction Indicator Light And
ESP/TCS Indicator Light................327

Tire Safety Information...................328
▫Tire Markings........................328
▫Tire Identification Number (TIN)..........331
▫Tire Loading And Tire Pressure...........332

Tires — General Information...............336
▫Tire Pressure.........................336
▫Tire Inflation Pressures.................337
▫Radial-Ply Tires......................339
▫Tire Spinning........................340
▫Tread Wear Indicators..................340
294 STARTING AND OPERATING

All vehicle wheels and tires must be the same size and
type and tires must be properly inflated to produce
accurate signals for the computer.
Anti-Lock Brake Light
The ABS light monitors the Anti-Lock Brake Sys-
tem. The light will come on when the ignition
switch is turned to the ON position and may stay on for
as long as four seconds.
If the ABS light remains on or comes on while driving, it
indicates that the Anti-Lock portion of the brake system
is not functioning and that service is required. However,
the conventional brake system will continue to operate
normally if the BRAKE warning light is not on.
If the ABS light is on, the brake system should be serviced
as soon as possible to restore the benefits of Anti-Lock
brakes. If the ABS light does not come on when the
Ignition switch is turned to the ON position, have the
bulb repaired as soon as possible.If both the Brake Warning Light and the ABS Light
remain on, the Anti-Lock brakes (ABS) and Electronic
Brake Force Distribution (EBD) systems are not function-
ing. Immediate repair to the ABS system is required.POWER STEERING
The standard power steering system will give you good
vehicle response and increased ease of maneuverability
in tight spaces. The system will provide mechanical
steering capability if power assist is lost.
If for some reason the power assist is interrupted, it will
still be possible to steer your vehicle. Under these condi-
tions, you will observe a substantial increase in steering
effort, especially at very low vehicle speeds and during
parking maneuvers.
NOTE:Increased noise levels at the end of the steering
wheel travel are considered normal and do not indicate
that there is a problem with the power steering system.
STARTING AND OPERATING 319
5

•The use of leaded gas is prohibited by Federal law.
Using leaded gasoline can impair engine performance
and damage the emissions control system.
•An out-of-tune engine or certain fuel or ignition mal-
functions can cause the catalytic converter to overheat.
If you notice a pungent burning odor or some light
smoke, your engine may be out of tune or malfunc-
tioning and may require immediate service. Contact
your authorized dealer for service assistance.
•The use of fuel additives, which are now being sold as
octane enhancers, is not recommended. Most of these
products contain high concentrations of methanol.
Fuel system damage or vehicle performance problems
resulting from the use of such fuels or additives is not
the responsibility of the manufacturer.
NOTE:Intentional tampering with the emissions con-
trol system can result in civil penalties being assessed
against you.
Carbon Monoxide Warnings
WARNING!
Carbon monoxide (CO) in exhaust gases is deadly.
Follow the precautions below to prevent carbon
monoxide poisoning:
•Do not inhale exhaust gases. They contain carbon
monoxide, a colorless and odorless gas, which can kill.
Never run the engine in a closed area, such as a
garage, and never sit in a parked vehicle with the
engine running for an extended period. If the vehicle is
stopped in an open area with the engine running for
more than a short period, adjust the ventilation system
to force fresh, outside air into the vehicle.
360 STARTING AND OPERATING

14. Disconnect the air pump hose (1) from the underside
of the sealant bottle (5) by flipping the hose valve open.
15. Connect the air pump hose valve to the tire valve and
flip the hose valve closed.
16. Leave the parking brake set and the shift lever in
PARK and start the engine.
17. Press the switch (3) on the air pump to I (ON). The air
pump should inflate the tire to at least 26 psi (1.8 bar)
within five minutes. If the tire inflates to this level,
proceed to the following step.NOTE:If a tire pressure of
26 psi (1.8 bar) is not obtained within five minutes, the
tire is too badly damaged. Do not attempt to drive the
vehicle further. Call for assistance.
18. With a tire pressure of no less than 26 psi (1.8 bar)
press the AIR PUMP switch (3) to 0 (OFF) and turn off the
engine. Then, disconnect the TIREFIT system from the
tire and place it back in the vehicle.19. Release the parking brake and drive the vehicle for
approximately 10 minutes to ensure optimum distribu-
tion of the tire sealant within the tire.
20. Turn on the hazard warning flashers.
21. Move the shift lever to the PARK position, turn off
the engine, and set the parking brake.
22. Disconnect the air pump hose (1) from the underside
of the sealant bottle (5) by flipping the hose valve open.
23. Connect the air pump hose valve to the tire valve and
flip the hose valve closed.
24. Check the pressure in the tire by reading the pressure
gauge (4). If the pressure is 19 psi (1.3 bar) or greater,
proceed to the following step.NOTE:If the pressure is
less than 19 psi (1.3 bar), the tire is too badly damaged.
Do not attempt to drive the vehicle further. Call for
assistance.
WHAT TO DO IN EMERGENCIES 375
6

25. Leave the parking brake set and the shift lever in
PARK and start the engine.
26. Inflate the tire to the pressure indicated on the tire
pressure label on the driver-side latch pillar by pressing
the switch (3) on the air pump to I (ON) and watching the
pressure gauge. When the tire pressure is set to the
pressure indicated on the tire pressure label, press the
AIR PUMP switch (3) to 0 (OFF) and turn off the engine.
27. Disconnect the TIREFIT system from the tire and
reinstall the valve cap.
28. Place the sealant kit back in the trunk of the vehicle.
Replace the sealant bottle at your nearest authorized
MOPARparts dealership.
29. Have the tire inspected at the earliest opportunity at
an authorized dealer or tire service center.NOTE:
•If a pressure of at least 19 psi (1.3 bar) cannot be
maintained in the tire, the tire is too badly damaged.
Do not attempt to drive the vehicle further. Call for
assistance.
•Do not operate the electric air pump for more than
eight minutes to avoid overheating. The air pump may
be used again once it has cooled down.
•Replace the TIREFIT sealant bottle (5) once every four
years to assure optimum operation of the system.
•If TIREFIT is liquid, clean water and a damp cloth will
remove the material from the vehicle or tire and wheel
components. Once TIREFIT sealing material has dried,
it can easily be peeled off and properly discarded.
•Do not exceed 55 mph (90 km/h) until the tire has
been inspected.
376 WHAT TO DO IN EMERGENCIES

Cavity Car-
tridge
FuseMini-
FuseDescription
39 — 10 Amp
RedHeated Mirrors - if
equipped
40 — 5 Amp
OrangeAuto Inside Rearview
Mirror/Heated Seats - if
equipped/Switch Bank
41 — 10 Amp
RedAC Heater Control/
Headlights/Park Assist -
if equipped/Tire Pres-
sure Monitoring - if
equipped/Occupant Re-
straint Controller (ORC)
42 30 Amp
Pink— Front Blower Motor
43 30 Amp
Pink— Rear Window DefrosterCavity Car-
tridge
FuseMini-
FuseDescription
44 20 Amp
Blue— Amplifier - if equipped/
Sunroof - if equipped
*Cavities 11, 12, and 13 contain self-resetting fuses
(circuit breakers) that are only serviceable by an autho-
rized dealer. The cluster, driver SEAT switch, and
memory module (if equipped) are fused by the 25-amp
circuit breaker in cavity 11. The passenger SEAT Switch is
fused by the 25-amp circuit breaker in cavity 12. The door
modules, the driver power WINDOW switch, and the
passenger power WINDOW switch are fused by the
25-amp circuit breaker in cavity 13. If you experience
temporary or permanent loss of these systems, see your
authorized dealer for service.
426 MAINTAINING YOUR VEHICLE

Auto Unlock, Doors....................... 30
Auto Up Power Windows.................. 34
Automatic Dimming Mirror................. 84
Automatic Door Locks................... 29,30
Automatic Headlights.................... 133
Automatic Temperature Control (ATC)......... 284
Automatic Transaxle
Special Additives...................... 414
Automatic Transmission.............305,413,414
Adding Fluid......................414,437
Autostick.........................308,310
Fluid and Filter Changes................. 414
Fluid Change......................... 414
Fluid Level Check...................... 413
FluidType ........................... 437
Shifting ............................. 305
Special Additives...................... 414
Automatic Transmission Limp Home Mode . . 309,310
Autostick...........................308,310AxleFluid ............................. 437
Axle Lubrication (Axle Fluid)............... 437
BallJoints ............................. 401
Battery............................... 397
Emergency Starting..................... 377
Jump Starting......................... 377
Keyless Transmitter Replacement (RKE)....... 23
Location..........................377,397
Bearings.............................. 414
Belts,Drive ............................ 393
Belts, Seat............................ 40,76
Body Mechanism Lubrication............... 401
B-Pillar Location........................ 332
Brake Assist System...................... 322
Brake Control System, Electronic............. 320
Brake Fluid............................ 437
Brake, Parking.......................... 315
Brake System........................317,410
INDEX 459
10