2008 CADILLAC CTS Owners Manual

CAUTION: (Continued)
To be even more certain the vehicle will not
move, you should put blocks at the front and
rear of the tire farthest away from the one
being changed. That would be the tire, on the
other side, at the opposite end of the vehicle.
When your vehicle has a at tire, use the following
example as a guide to assist you in the placement of
wheel blocks.
The following information tells you how to use the jack
and change a tire.
5-103

Removing the Spare Tire and Tools
A. Wing Nut
B. Spare Tire
C. JackD. Wheel Wrench
E. Extension
F. Strap
The equipment you will need is in the trunk.To gain access to the spare tire and jacking equipment,
do the following:
1. Remove the spare tire cover.
2. Remove the stow rod cap by pulling it straight up
off of the rod.
3. Turn the wing nut (A) on the compact spare tire (B)
counterclockwise to remove it.
4. Remove the spare tire and place it next to the
at tire.
5. The tools you will be using next include the jack (C),
wheel wrench (D), and extension (E).
5-104

Removing the Flat Tire and
Installing the Spare Tire
1. Do a safety check before proceeding. SeeChanging
a Flat Tire on page 5-102for more information.
2. Loosen the wheel nuts, but do not remove them
yet, using the wheel wrench. Turn the handle
about 180 degrees, then return the handle back
to the starting position. This avoids taking the
wrench off the lug nut for each turn.3. Find the jacking location using the diagram above
and corresponding V-shaped locating notches
located in the plastic molding.
5-105

4. Insert the hooked end of the extension handle
through the jack and the at end through the
wheel wrench.
{CAUTION:
Getting under a vehicle when it is jacked up is
dangerous. If the vehicle slips off the jack, you
could be badly injured or killed. Never get under
a vehicle when it is supported only by a jack.
{CAUTION:
Lifting a vehicle and getting under it to do
maintenance or repairs is dangerous without
the appropriate safety equipment and training.
The jack provided with your vehicle is
designed only for changing a at tire. If it is
used for anything else, you or others could be
badly injured or killed if the vehicle slips off
the jack. Use the jack provided with your
vehicle only for changing a at tire.
{CAUTION:
Raising your vehicle with the jack improperly
positioned can damage the vehicle and even
make the vehicle fall. To help avoid personal
injury and vehicle damage, be sure to t the
jack lift head into the proper location before
raising the vehicle.
5-106

Notice:If you position the jack under the rocker
molding and attempt to raise the vehicle, you could
break the molding and/or cause other damage to
your vehicle. Always position the jack so that when
the jack head is raised, it will t rmly in the
notch located inboard from the rocker molding.
5. Turn the wheel wrench counterclockwise to lower
the jack lift head until the jack ts under the vehicle.
6. Raise the jack by turning the wheel wrench
clockwise until the slots in the jack head t into the
metal ange located behind the V–shaped locating
notches on the plastic molding as shown.7. Put the compact spare tire near you.
8. Raise the vehicle by turning the wheel wrench
clockwise. Raise the vehicle far enough off the
ground for the compact spare tire to t under the
vehicle.
9. Remove all the wheel
nuts and the at tire.
5-107

{CAUTION:
Rust or dirt on a wheel, or on the parts to
which it is fastened, can make wheel nuts
become loose after time. The wheel could
come off and cause an accident. When you
change a wheel, remove any rust or dirt from
places where the wheel attaches to the vehicle.
In an emergency, you can use a cloth or a
paper towel to do this; but be sure to use a
scraper or wire brush later, if needed, to get all
the rust or dirt off. SeeChanging a Flat Tire on
page 5-102.
{CAUTION:
Never use oil or grease on bolts or nuts.
Because the nuts might come loose. The
vehicle’s wheel could fall off, causing a crash.10. Remove any rust or dirt
from the wheel bolts,
mounting surfaces, and
spare wheel.
11. Install the spare tire.
12. Put the wheel nuts back on with the rounded end of
the nuts toward the wheel.
13. Tighten each wheel nut by turning it clockwise with
your hand until the wheel is held against the hub.
14. Lower the vehicle by turning the wheel wrench
counterclockwise. Lower the jack completely.
5-108

{CAUTION:
Incorrect or improperly tightened wheel nuts
can cause the wheel to come loose and even
come off. This could lead to a crash. If you have
to replace them, be sure to get new original
equipment wheel nuts. Stop somewhere as
soon as you can and have the nuts tightened
with a torque wrench to the proper torque
specication. SeeCapacities and Specifications
on page 5-129for wheel nut torque
specication.Notice:Improperly tightened wheel nuts can
lead to brake pulsation and rotor damage. To avoid
expensive brake repairs, evenly tighten the wheel
nuts in the proper sequence and to the proper torque
specication. SeeCapacities and Specifications on
page 5-129for the wheel nut torque specication.
15. Tighten the wheel nuts
rmly in a crisscross
sequence as shown.
5-109

Storing a Flat or Spare Tire and
Tools
{CAUTION:
Storing a jack, a tire, or other equipment in the
passenger compartment of the vehicle could
cause injury. In a sudden stop or collision,
loose equipment could strike someone.
Store all these in the proper place.
After you have put the compact spare tire on your
vehicle, you will need to store the at tire in your trunk.
The compact spare is for temporary use only. Replace
the compact spare tire with a full-size tire as soon
as you can.Use the following diagram as a guide for storing the
compact spare tire in the trunk:
A. Wing Nut
B. Compact Spare Tire
or Flat Tire (valve
stem down)C. Jack
D. Wheel Wrench
E. Extension
F. Strap
5-110