2008 AUDI S8 ignition

Opening and clo sing
Emergency closing by hand
The sunroof can be closed by han d in case of a power
failure.
• • l Q 0
Removing th e cover
Fig . 54 Sec tio n from
hea dlin er: W here t o
p la ce the sc rew driv er
F ig . 55 Sec tio n fr om
h ea dliner : Cra n k for
e m erg ency oper ation
- Insert the flat side of the screwdriver (found in t he
vehicle tool kit) at the rear edge of the lens as indicated
by the -a rrows- => fig. 54 .
- Carefully pry the c lear lens cover open and remove it.
Retri eving the cra nk for em erg ency closing
- Use the ignition key or a screwdriver to carefully pry the
cover off the left end of the instrument panel
=>
page 358, fig. 29 1. The crank is stored next to the fuse
earner.
Closing the roof
- Pus h the crank G) => fig. 55 into the hex socket @ until
you can feel the crank engage . Start turning, maintain ing
a steady pressure on the crank to keep it from slipping
off.
- After you have closed the sunroof, remove the crank and
replace the dome lig ht lens.
[ i] Tip s
If you are unable to close the roof manually , contact the nearest
authorized Audi dealer for assistance. •

Clear vision
Lights
Switching the headlights on and off -'t/-·
In the "AUTO" position, a light sensor automatically
s w itches t he head- and taillights on and off in respo nse to
l igh t con ditions.
Fig . 56 In stru ment
pan el: lig ht sw itch
Switching on automatic headlight control
- T urn th e light switch to AUTO => fig. 56 .
Switching on the side marker lights
- Turn the light switch to ~oo~.
Switching on th e headlights and high beam
- T urn t he light swi tch to io.
- Push the high beam leve r forw ard towards t he instru -
me nt panel
=> page 73 .
Switching off the lights
- T urn t he light switch to 0 .
Contro ls a nd eq uip­
ment
Clear vision
The head lights only work when the ignition is switched on . While
starting the engine or when switching off the ignition, the head ­
lights will go off and only the side marker lights will be on.
After starting the engine, the xenon headlights are automatically
adjus ted to the load and angle of the vehic le (for example, during
acceleration, braking) . This prevents oncoming traffic from experi ­
encing unnecessary headlig ht g lare from your xenon head ligh ts .
If the system is not operating properly, a warning symbol in the
Auto -Check Control is displayed
=> page 36.
With the side marker lights or head ligh ts switched on, the sym bol
next to the light switch illuminates
:oo: .
Daytime running lights
• USA models : The daytime running lights wi ll come on automati­
ca lly when the ig nition is turned on and the ligh t
switch=> fig. 56 is
in the
O position or the AUTO position (only in day light conditions).
The
Daytime running lights function can be turned on and off in the
MMI menu
Exterior lighti ng => page 70 => & .
• Canada models: The dayti me ru nn ing lights wi ll come on auto ­
matically when the ignition is turned on and the light switch
::::> fig. 56 is in the O position or the AUTO p o siti on (only in daylight
conditions)
=> & .
Automati c headligh t control
In the switch position AUTO the a utomatic headligh t cont rol is
turned on . The low beams are turned on automa tica lly through a
light sensor as soon as ambient brightness (e.g . when driving into a
tunnel) fa lls below a value preset at the factory . When ambient
brightness increases again, the low beams are turned off again
automatically =>& .
In the AUTO pos it ion the low beams are switched off automatically
when the ignition is turned off. If the high beams were switched on,
they w ill come o n again the next time the automatic head ligh t
~
Vehicle care I I irechnical data

Clear vision
control is activated. The high beam function must first be switched
on in the MMI
=> page 70 .
Light Sensor Malfunction
In the event of a light sensor mal fu n ct ion, the driver is notified i n the
instrument cluster display :
@ Automatic headlights/automatic wipers defe ctive
For safety reasons the low beams are turned on permanently with
the switch in
AUTO . However, you can continue to turn the lights on
and off us ing the light switch . Have the light sensor checked as soon
as possib le at a dealership .
& WARNING
• Never use dayt ime running lights to see where you are going .
The y are not bright enough and will not let you see f ar enough
ahead for s afet y, espe cially at du sk or when it is d ark. Alwa ys
switch on the low beams at dusk or when it is dark .
• Autom atic he adlight s are onl y intended to a ssist the dr iver.
The y do n ot relie ve the dri ver of his re spon sibility to che ck the
headlights and to turn them on manuall y according to the current
light and vi sibility condi tion s. For example , fog and rain cannot be
dete cted b y the l ight sen sors . S o alway s switch on the he adlights
under these wea the r condition s and when driving in the dark
gD .
• Cra shes can h appen when you c annot see the road ahead and
when you cannot be seen b y other motori sts .
- Alway s turn on the headlight s so that you can see ahead and
s o that others c an see your c ar from the ba ck.
[ i ] Tips
• With the switch in AUTO front fog lights and rear fog lights
cannot be turned on in addition. • I
f you remove the ignition from the ignition lock while the head ­
li ghts are s til l on, a bu zzer w ill sound as long as the driver's door is
open to remind you to turn off the lights .
• Always observe t he specific local regulations for your area as to
when to use your lights .•
Adjusting exterior lighting
The functions are set in the MM/.
F ig . 57 MM I di spla y:
E xt eri or ligh ting
- Pressthe [CAR ]function button.
- Select
Systems in the CAR me nu.
- Selec t
Exterior lighting. The menu Exterior lighting
appears => fig. 57.
C oming home
The Coming home function ensures that after turning off the igni ­
tion and op ening the driv er's door
the vehicle periphery is il lum i­
nated in the dark . In addition, the front fog lights, the tail lights and
t he license plate lig ht are turned on . O n-t ime can be set fo r a period
from
O (off) to 60 seconds. ~

Le avi ng hom e
The Leaving home functions ensures that when unlocking the
vehicle periphery is i lluminated in the dark . In addition, the fron t fog
lights, the tai l lights and the license plate light a re turned on. Th is
function can be turned on and off .
High beam
With the switch in the AUTO position, the high beams can be turned
on only if the function is turned
on.
D aytime ru nning l ight s
USA models:
The daytime running lights can be turned on or off
using this function .
Canada models: The function cannot be tu rned off . It is activated
automatically each time t he ignition is turned on. This menu item is
shown "greyed out" .•
Front fog lights }0
Fi g. 58 Ins tru men t
pan el: lig ht swit ch
Switching on the front fog lights }D
- Do not turn the light switch -r:;_ -=> fig. 58 toward the fog
l ight symbol
- Tu rn t he light switch to
~oo: o r to fD .
Contro ls a nd eq uip­
ment
Clear vision
- P ull the ligh t switch to th e fi rst st op G) .
When the front fog l ights are on, the symbo l }D next to the ligh t
switch will illuminate .
[ i ] Tips
With the switch in AUTO front fog lights and rear fog lights cannot
b e turned on in addition .•
R ear fog lights 0$
Fig . 59 In strument
p an el: lig ht sw itc h
- Do not turn the light sw itch -r:;_ -=> fig. 59 toward the fog
light symbol
- Turn the light sw itch to
~oo: or to fD.
- Pull the light swit ch t o th e second stop 0-
W hen the rear fog lights are on, both the }D and
the light switch will i llum inate. symbols next to
~
Vehicle care I I irechnical data

Clear vision
High b eam
~D
Push the lever forward to switch on the high beam.
- Pull the lever back towards you to switch off the high
beam .
Headlight flasher ~D
- Pull the lever toward the steering wheel to use t he head­
light flasher .
Notes on the se feature s
• The turn signals only work with the ignition turned on . Th e indi­
cator
l ights ¢ or¢ in the instrument cluster ~ page 16 also blink .
• After you have turned a corner, the turn signal switches off auto ­
matical ly .
• The high beam works only when the head lights are on . The indi ­
cator light
~D in the instrument cluster illuminates when the high
beams are on.
• The headlight flasher works only as long as you hold the lever -
even if ther e are no lights turned on. The indicator light
~D in the
instrument cluster illuminates when you use the headl ight flasher.
• With the switch in the
AUTO position, the high beams can only
be turned on if the function is switched on in MM I
=> page 70.
0 Note
Do not use the high beam or headlight flasher if you know that these
could blind oncoming traffic .•
Interior lights
Front interior lights
T he in terior lights include rea ding ligh ts for b oth the
d river and the fr ont passenge r.
--
1111
, I I, . II
-
~
•
'
'.(ZW
ro ,1@1
111111111
0
Interior lights
-
®
111111111
...
/!
111111111
0 Fig . 6 3 Rooflining:
Fr ont inter ior light s
Fi g. 64 Rooflining:
F ront readin g ligh ts:
- Press the @J button to tur n off the interior lights
~ fig . 63. If you pre ss the butt on a secon d time, the inte­
ri o r ligh ts in the rear ar e also t urned off .
- Press the
(ID butto n to turn on the door contact circui t.
Press the button a second time to tur n on the door
contact circ uit for the rear doors .

-Press the CD button to turn on the interior lights. If you
press the button a second time, the interior lights in the
rear are also turned on.
Reading lights ~
Press the switch to turn the right or left reading light on
or
off=:> page 74, fig. 64.
With the door contact circuit, 00 the interior lights turn on as soon
as you unlock the vehicle or open the doors. The interior lights are
also turned on when the ignition key is removed. The light goes out
about 2 minutes after the doors are closed. When the vehicle is
locked or when the ignition is turned on, the interior lights are
turned off .
When a door is open, the interior lights are turned off after about 10
minutes to prevent draining the battery .
[ i] Tips
The interior lights can be dimmed by holding the [D switch pressed
down. If the interior lights in the rear were turned on by pressing the
switch twice, the rear interior lights are also dimmed .•
Contro ls a nd eq uip­
ment
Clear vision
Rear Interior Lights
The rear interior lights also contain reading lights for
rear-seat passengers.
Fig. 65 Rooflining:
Rear interior lights
Fig . 66 Rooflining:
Rear reading lights
Interior lights
-Press the@) button to turn off the interior lights
=:> fig. 65.
-Press the (ID button to turn on the door contact circuit.
-Press the CD button to turn on the interior lights.
Vehicle care I I irechnical data

Clear vision
Reading lights
~
Press one of the switches to turn the right or left reading
light on or
off~ page 75, fig. 66.
With the door contact circuit, 00 the interior lights turn on as soon
as you unlock the vehicle or open the doors. The interior lights are
also turned on when the ignition key is removed . The light goes out
about 2 minutes after the doors are closed. When the vehicle is
locked or when the ignition is turned on, the interior lights are
turned off.
When a door is open, the interior lights are turned off after about 10 minutes to prevent draining the battery .
[ i) Tips
• By pressing the safety switch @~ page 62, fig. 48, the function
of some switches in the rear can be turned off. If the symbol in
the safety switch illuminates, the window regulators in the rear
doors, the switches for the interior lights and the switch for the elec ­
tric sun shade* are inoperative.
• The interior lights can be dimmed by holding the
(I] switch
pressed down. •
Applies to vehic les: w ith backg round lightin g
Background lighting
Four different lighting profiles for the interior lighting can
be selected and dimmed through the MM/.
~/®~~
111111111 ~ 111111111
0 ~ 0
Fig . 67 MMI display :
Background lighting
Fig. 68 Roof module
cutout: Light profile
switch
- Press the Systems control button in the car menu.
- Select
Background lighting .
- Select a lighting profile~ fig. 67 or select Off to deacti-
vate the lighting profile.
- Press the control knob to activate the desired lighting
profile .

-Rotate the control knob clockwise to increase the bright­
ness, and
Rotate the control knob
counterclockwise to reduce the
brightness.
When the vehicle is unlocked, the standard lighting turns on auto­
matically and dims after approx. 2 minutes, and when the ignition is
turned on it switches off immediate ly.
A background lighting profile can be switched on manually using
the light profile
switch ~ page 76, fig. 68. This wi ll turn off automat ­
ically after 30 minutes when the ignition is off. To reac tivate , press
the lighting profile switch.
Lighting profiles that were selected while driving remain active
during the course of travel.
The following lighting profiles can be adjusted and
dimmed in the MMI:
Driver's side footwell
Passenger's side foot -
well
Rear footwell
Rear door trim panel
Front interior lighting
Rear interior lighting
[ i J Tips
Highway
X
X
X
X X
X X
X
X
Cockpit Rear
X
X
X
X
X
X
X
Lighting profiles are stored on the remote control key being used. •
Controls a nd eq uip­
ment
Clear vision
Vision
Sun visors
Using the sun visors makes driving safer.
] ~
J_~---~..r-:::Jli
WAANINO ..,
f,":a(S) ::-,....= ~ =­
=:.:=-..:GJ
- -, - ~~ ,.. __ ..... _ ... -----__ ..., ______ ---
~
,l,
\,;....l--------:.:r.::Jli
WAANINO ATTENTIOH
-- ---­
_____ ,.. ..
-----··
___ .. _
-·- ------------- ·----·---... -------------·-----
Fig . 69 Sun visor
Fig. 70 Sun visor with
two-part vanity mirror
The sun visors for the driver and front passenger can be removed
from their center mountings and moved toward the door windows
G) ~ fig. 69 to protect against side glare. After you have moved the
sun visors so that they are parallel to the door windows, you can pull
out the extensions.
Between the visors for the driver and the passenger there is a
folding visor which can be used to cover the space above the rear
view mirror.
Vehicle care I I Technical data