2008 AUDI A8 wheel

Menus155
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
•Extract number - to copy a telephone number from a text
message into the display for editing.
•Edit - to edit a text message open in the inbox.
•Forward - to forward a text message you have received to
another telephone number.
Templates
The Templates menu is used to insert a text template (e.g. I will be
late ...) into a text message.
Text message settings
•Status report - to receive a delivery status report from the
message centre after you send a text message.
•Va li dity - to specify how long text messages are held at the
message centre.
•Service centre - to retrieve or change the number of the message
centre.
•Memory capacity - to display the total capacity of the text
message memory and the amount of memory used.
•Store text msg - to store text messages in the outbox when they
are sent. The memory can fill up quickly if you activate this function.
If the memory is full, the crossed-out envelope symbol will appear
in the display and no more text messages can be received.
Delete txt msgs
•Read - to delete read text messages from the inbox.
•Unread - to delete unread text messages from the inbox.
•Sent - to delete text messages you have written and sent.
•Unsent - to delete text messages you have written but not sent.
•Delete all - to delete all text messages on the SIM card.
Note
The handset display shows only text messages which are stored on
the SIM card.
Applies to vehicles: with handset for the car telephone kit
“Settings” menu (handset)
– Press the control button for Menu
page 142,
fig. 126.
– Select Settings using the navigation button.
Switch off tel.
The car telephone kit logs off the GSM network and shuts down but
the handset remains connected. If mobile phones are connected,
these connections are closed.
The car telephone kit can be switched on again from the handset
and will automatically log onto the GSM network.
Fig. 143 Settings
Fig. 144 Ring tone
volume
A8










Menus157
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control connected mobile phone with SIM Access Profile, you will have to
enter the PIN again on the mobile phone after the Bluetooth connec-
tion between the car telephone kit and the mobile phone is termi-
nated. Otherwise you will not be available.
•Call barring - you can set up access restrictions for incoming and
outgoing calls. Select Deactivate all to cancel all restricted access
settings. The call barring function requires a password. You can
obtain the password from your mobile network service provider. The
call barring options depend on your mobile network service
provider. For more information, contact your service provider.
These settings are also applied on the MMI
page 98.
Mailbox number
The mailbox number is entered on the handset display and then
stored on the handset.
Once the number has been stored, you can call the mailbox using
one-touch dialling
page 146.
This service must be set up beforehand. For more information,
contact your service provider.
Use the Options to Store the mailbox number, Search for it in the
phone book, or Delete it.
The mailbox number has to be entered separately on the MMI

page 98 or
page 102.
Call forward
•Voice calls - to forward incoming calls to your mailbox or another
number. Select Forward all calls to forward all incoming voice calls.
Select If busy to forward voice calls received when you are already
talking on the phone. Select If not available to forward voice calls
when the telephone is switched off. Select If no answer to forward
voice calls that you do not answer. Select Status to check the
current setting for the Vo ic e c a l ls function.
•Fax calls - to forward Fax calls to the specified number.
•Data calls - to forward Data calls to the specified number.
•Deactivate all - to cancel all call forward settings.
These settings are also applied on the MMI
page 99.
Network selection
•Automatic - your telephone will automatically log into your
mobile service provider network.
•Manual - a list of all available networks will appear on the display.
•Select network - the networks for your present location are
listed. You can choose any of the available networks. This function
can be used when the Manual setting is activated for network selec-
tion.
These settings are also applied on the MMI
page 99.
Software version
To display the handset software version.
Note
•If you are using a twin card in the handset, you should activate
the PIN query
page 98. The SIM card in the vehicle is then only
activated when you enter the PIN.
•When using a twin card please follow the recommendations of
your provider. Otherwise, you may experience connection problems
and callers may not be able to reach you.
•These settings depend on your mobile network service
provider.










Telephone speech control system161
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
Basic operation
Applies to vehicles: with telephone speech control system
Switching on and off
The speech control system can be activated via the talk
button on the mobile phone adapter or the button on the
multi-function steering wheel*.
Important: The ignition must be switched on and no phone
calls must be active.Switching on
– Press the talk button on the mobile phone adapter*
26)

fig. 145, or
– Press the talk button on the multi-function steering
wheel
fig. 146. A signal tone will indicate that the
speech control system is ready. The message “The
speech dialogue system is activated” will appear in the
MMI display.
– Say the desired command.
Switching off
– Say the command CANCEL, or
– Press the talk button on the mobile phone adapter*
26)

fig. 145, or
– Press and hold the talk button on the multi-function
steering wheel
fig. 146 until you hear the cue
.
Applies to vehicles: with telephone speech control system
Adjusting the volume
Important: The speech control system must be switched on

page 161, and the system must be giving a cue.
– Scroll the right thumbwheel on the multi-function
steering wheel
fig. 146 up
 or down , or
– Turn the ON/OFF button on the MMI control console

page 45 to increase or reduce the volume.
Fig. 145 Talk button on
the mobile phone
adapter
Fig. 146 Multi-func-
tion steering wheel:
Talk button and right
thumbwheel
26)Applies to phone pre-installation.



A1



A1
A2





!




Telephone speech control system163
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
Applies to vehicles: with telephone speech control system
Dialling a number
Important: The speech control system must be switched on

page 161.
Dial number
– Say the command DIAL NUMBER. The speech control
system will ask you to enter a telephone number.
– Say the digits of the telephone number individually or in
groups. After each block of digits you specify, the system
will repeat the digits.
–Say DIAL when you have completed the number entry.
The telephone number will be dialled.
Select name
– Say the command SELECT NAME.
– When the speech control system gives you the cue, say a
name that has previously been recorded
page 165.
– Say the command DIAL. The telephone number will be
dialled.
Play phone book
– Say the command PLAY PHONE BOOK. The name tags will
now be read out.
– To select the telephone number of a recorded name
simply press the talk button while this recorded name is
being read out.Note
•Recorded names are user-oriented and are best recognised by
the system when the same person who assigned the name repeats
the recorded name.
•During the dialogue you can use the commands REPEAT, BACK,
and DELETE.
Applies to vehicles: with telephone speech control system
Redialling
Important: The speech control system must be switched on

page 161.
– Say the command REDIAL. The last telephone number
you used will be dialled.
Note
•On some mobile phones the number you dialled last is placed at
the bottom of the call list. In this case, the redial function of the
speech control system cannot be used.
•During the dialogue you can use the commands REPEAT, BACK,
and DELETE.





! 




Telephone speech control system 164
Name tags
Applies to vehicles: with telephone speech control system
Introduction
Name tags are stored in the phone book for the speech
control system.
General notes
The phone book for the speech control system has 50 memory posi-
tions. You can use it independently of the mobile phone. The name
tags are stored in the phone book for the speech control system.
In the phone book for the speech control system you can assign
recorded names (name tags) to entries stored in the phone book of
the on-board phone system (car telephone kit* or phone pre-instal-
lation*). You can also store new entries with recorded names and
telephone numbers in the phone book for the speech control
system
page 165. These entries are stored separately from the
entries in the on-board phone book (car telephone kit* or phone pre-
installation*).
Once you have stored name tags in the phone book for the speech
control system, you can select them via the speech control system.
Entering
You should choose spoken names that can be identified clearly by
the speech control system.
Numbers from ZERO to NINE are recognised when you enter a tele-
phone number. The telephone number can be specified all at once,
in blocks of digits (separated by a brief pause), or as single digits.
After each block of digits you specify (separated by a brief pause)
the system will repeat the digits. The system can only recognise
single digits (TWO, THREE, etc.), and not combinations of digits (e.g.
twenty-three).
If the telephone number has more than 20 digits, the system will
decline and give the cue . A Plus (+) can
also be placed ahead of the 20 digits.
Applies to vehicles: with telephone speech control system
Storing a name tag for a phone book entry
You can store a name tag for a phone book entry shown
in the display of the driver information system.
Important: There must be entries stored in the phone book.
– Press the button on the multi-function steering
wheel
page 128 repeatedly until the telephone menu

page 133, fig. 117 appears in the display of the driver
information system.
– Scroll the left thumbwheel on the multi-function steering
wheel to select Phone book
page 133, fig. 117 and
press the left thumbwheel. The phone book entries will
be displayed.
– Scroll the left thumbwheel to mark the phone book entry
you wish to select.
– Press the talk button on the multi-function steering
wheel
page 161, fig. 146. The tone will
sound.
– Say the command STORE.
Fig. 148 Phone book
entry with name tag
MODE

A1





!




Telephone speech control system165
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
– Say the name under which you wish to store this phone
book entry when the speech control system gives you the
cue.
– Repeat the name when you are requested to do so. The
recorded name (name tag) for the selected phone book
entry will be stored in the phone book for the speech
control system.
If a name tag has been stored for a phone book entry, that entry will
be marked by a symbol
page 164, fig. 148 in the display of the
driver information system.
Applies to vehicles: with telephone speech control system
Storing a name tag with a telephone number
Name tags consisting of a name and assigned telephone
numbers can be stored in the phone book for the speech
control system.
Important: The speech control system must be switched on

page 161.
– Say the command STORE NAME.
– Say the name under which you wish to store this phone
book entry when the speech control system gives you the
cue.
– Repeat the name when you are requested to do so.
– When requested, say the digits of the corresponding
telephone number individually or in groups. After each
block of digits you specify, the system will repeat the
digits it has recognised.–Say STORE when you have completed the number entry.
The entry will then be stored in the phone book for the
speech control system.
Name tags which you have stored in the phone book for the speech
control system using the STORE NAME command will not be shown
in the display of the driver information system.
Note
If two or more names sound alike, it is better to save the names
including the first name or some other distinguishing entry.
Applies to vehicles: with telephone speech control system
Deleting a name tag with a telephone number
Important: The speech control system must be switched on

page 161.
– Switch on the speech control system
page 161.
– Say the command DELETE NAME.
– When the speech control system gives you the cue, say a
name that has previously been recorded
page 165.
– When the speech control system gives you the cue, say
YES to delete a recorded name which was previously
stored in the phone book for the speech control system.
This is to confirm that you wish to delete the entry.
If you say No, the system will answer with and the
dialogue will be ended.
A1





!




Speech recognition for some export markets167
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
Speech recognition for some export markets
Applies to vehicles: with telephone speech control system
Storing names in the phone book*
If your vehicle is equipped accordingly, you can assign
name tags (voice entries) to the entries from the SIM card
or the mobile phone directory.
– Press the button on the multi-function steering
wheel
fig. 149 repeatedly until the telephone menu

fig. 150 appears in the display of the driver informa-
tion system.– Scroll with the left thumbwheel to Phone book and press
to confirm
fig. 150. The entries of the on-board phone
memory will be displayed.
– Scroll and press the left thumbwheel to select one of the
listed entries of the on-board phone memory.
– Press the talk button on the multi-function steering
wheel. You will then hear a beep.
– Say the name you wish to save for this phone book entry.
You will then hear a double beep.
– Repeat the name. The system will repeat the recorded
name and an ascending sequence of tones will confirm
that the entry has been accepted.
If the entry was not accepted the system will emit a descending
sequence of tones to request that you enter the name again.
If a recorded name has been stored for a phone book entry in the on-
board phone memory (phone pre-installation), this entry will be
marked by a symbol
page 168, fig. 151 in the display of the
driver information system.
A running dialogue can be cancelled at any time by pressing and
holding the talk button on the multi-function steering wheel .
Note
•If two or more names sound alike, it is better to save the names
including the first name or some other distinguishing entry.
•The phone book with the name tags (voice entries) only works in
conjunction with the speech control system. The recorded names
(name tags) are not stored in the on-board phone memory.
Fig. 149 Multi-func-
tion steering wheel
Fig. 150 Telephone
menu
MODE

A1






!




Speech recognition for some export markets 168
Applies to vehicles: with telephone speech control system
Selecting a name from the phone
book*
Stored name tags can be selected.
– Press the talk button on the multi-function steering
wheel
page 167, fig. 149. You will then hear a beep.
– Say the recorded name which you wish to select

page 167. You will then hear a double beep.
You will hear an ascending sequence of tones to confirm that the
system has recognised the name. The number for the person you
wish to call will then be dialled.
If the system failed to recognise the name, you will hear a
descending sequence of tones. Please say the recorded name again.
If a name tag has been stored for a phone book entry in the on-board
phone memory (phone pre-installation), this entry will be marked by
a symbol
fig. 151 in the display of the driver information
system.
A running dialogue can be cancelled at any time by pressing and
holding the talk button.
Applies to vehicles: with telephone speech control system
Deleting a name from the phone
book*
Stored name tags can be deleted as desired.
– Press the button on the multi-function steering
wheel
page 167, fig. 149 repeatedly until the tele-
phone menu
page 167, fig. 150 appears in the display
of the driver information system.
– Scroll with the left thumbwheel to Phone book and press
to confirm
page 167, fig. 150. The entries of the on-
board phone memory will be displayed.
– Use the left thumbwheel to scroll through the phone
book and to select an entry marked with a horizontal
arrow.
– Press the talk button . The recorded name (name tag)
is deleted.
When you have deleted a recorded name (name tag), the symbol

fig. 151 in front of the phone book entry will also be deleted in the
display of the driver information system.
Fig. 151 Phone book
entry in on-board
phone memory with
recorded name tag

A1
MODE

A1





!