2008 AUDI A8 phone

Navigation 116
– Start the route guidance by turning the rotary push-
button to Start route guidance and then pressing the
rotary pushbutton. The route criteria and subsequently
the map
page 110 will be shown on the MMI display.
An arrow will appear in the display of the driver informa-
tion system.
Other settings
Applies to vehicles: with navigation system
Special destinations
Special destinations can be selected in the entry space
when entering single destinations or stopovers.
– Select: Function selector button > Special
destination, or
– Select: Function selector button > stopover >
Special destination.
The navigation system can also guide you to special destinations
such as petrol stations or hotels. When entering your destination,
simply choose the approximate location of the special destination
(in the immediate vicinity, in the vicinity of the destination or nation-
wide). You can then select the category of the special destination
from a list (e.g. petrol station or hotel). The MMI display even indi-
cates the direction of the special destinations (arrows).
In immediate vicinity
The special destination is located in the immediate vicinity of your
vehicle. The special destinations are sorted according to the
distance from your current location, starting with the closest. You
can use this function, for example, to plan stopovers (closest restau-
rant).In vicinity of destination
The special destination is located in the vicinity of your destination.
You can use this function, for example, to find a petrol station near
your destination.
Nationwide
A special destination can be found irrespective of your current posi-
tion and your navigation destination. You can use this function, for
example, to navigate to an airport in the selected country.
Call: (telephone number)*
If telephone numbers are stored for a special destination on the
navigation DVD and your vehicle is equipped with a factory-fitted
telephone*, you can call the selected special destination. For
example, you can call a restaurant and reserve a table before driving
to the destination.
Note
There are certain destination entries in the list that cannot be
displayed completely because they are too long (too many charac-
ters). If you select one of these entries, a separate window will be
displayed after a few seconds. This window will show more informa-
tion about the selected entry.
Applies to vehicles: with navigation system
Top destination
– Select: Function selector button , or
– Select: Function selector button > stopover.
When storing a navigation destination, you can activate the func-
tion Display as top destination (). Top destinations are listed in the
destination entry screen
page 105, fig. 91 and can be copied into
the destination entry field directly.
NAV
NAV
NAV
NAV





!




Navigation117
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
Applies to vehicles: with navigation system
Deleting a route
– Select: Function selector button > control button
Memory > Delete route.
Stored route plans (routes with stopovers) will now be deleted.
Applies to vehicles: with navigation system
Changing a route plan
A route plan (Route with stopover) can be changed, moved, deleted
or set as a destination again. Simply use the rotary pushbutton to
select the destination or a stopover on the route plan and then press
the rotary pushbutton. Then select one of the options displayed.
If you delete the destination, the last stopover will automatically be
set as the new destination.
Applies to vehicles: with navigation system
Route list
– Select: Function selector button > control button
Route > Route list.
The route list is only visible when the route guidance is active and
contains the following information:
•Details of the route
•Distances
•Street names
•Town and place names
Applies to vehicles: with navigation system
Route criteria
– Select: Function selector button > control button
Route > Route criteria.
The route will be calculated according to various criteria.
Dynamic navigation
The dynamic navigation function optimises a route plan by using
the most current traffic reports to automatically recalculate routes
and avoid traffic jams.
If the navigation does not display a detour route, although the
dynamic navigation function is ON and a traffic jam has been
reported on the planned route, this is because the estimated time
required for the detour is longer than the estimated time required
for remaining on the route with the traffic jam.
Route options
The navigation system selects the faster or shorter route.
Motorway / ferry / toll road
If you do not want the navigation system to include motorways,
ferries or toll roads in the route calculation, you can set the option
avoid. However, there can be situations in which you will not be able
to avoid them.
Note
If one of the selected criteria is unavoidable (i.e. the route must
contain the undesired criterion), the system will automatically
calculate the route accordingly.
NAV
NAV
NAV










Navigation 118
Applies to vehicles: with navigation system
Avoiding a route
– Select: Function selector button > control button
Route > Avoid route from here.
When the route guidance is activated, a section of the calculated
route that you have set will be avoided. The navigation system will
calculate an alternative route.
Using the rotary pushbutton, select the length of the route which is
to be avoided.
If you stop and restart the route guidance, it will be necessary to
reenter the route section to be avoided.
Note
If the MMI is not able to offer an alternative route, this indicates that
no suitable detour is available in the vicinity.
Applies to vehicles: with navigation system
Navigation details
– Select: Function selector button > control button
Nav-Info.
When the route guidance is activated, the following information on
your destination will be displayed:
•Destination / stopovers
•Estimated time of arrival
•Distance to the destination
•Current position of the vehicle
•Longitude and latitude coordinates of the destination
•Longitude, latitude and altitude of the vehicle
•Satellites received
The last route guidance cue will be repeated.
Call: (telephone number)*
If telephone numbers are stored for a special destination on the
navigation DVD and your vehicle is equipped with a factory-fitted
telephone*, you can call the selected special destination. For
example, you can call a restaurant and reserve a table before driving
to the destination.
Applies to vehicles: with navigation system
Map colours
– Select: Function selector button > function
selector button > Map colours.
Day
The map background will be lit brightly.
Night
The map background will be darkened.
Auto
When the dipped lights are on, the map scheme will switch from day
to night.
Applies to vehicles: with navigation system
Orientation
– Select: Function selector button > function
selector button > Orientation.
North
The map is set to face north. The position of the arrow will change
according to the movement and direction of the vehicle.
NAV
NAV
NAV
SETUP
NAV
SETUP










Navigation119
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control Direction of travel
The map is set to face the direction of travel. If the map scale is
between 50 m and 50 km, the map will rotate according to the direc-
tion of travel.
Auto
If the scale is less than 2.5 km, the map is set to face the direction
of travel. If the scale is more than 2.5 km, the map is set to face
north.
Applies to vehicles: with navigation system
Intersection zoom
– Select: Function selector button > function
selector button > Intersect. zoom.
When the intersection zoom function is activated, any intersection
will be zoomed in on automatically. This provides a detailed view,
giving you a better perspective of the road layout. When zooming,
the map will automatically be set to face the direction of travel.
Applies to vehicles: with navigation system
Map type
– Select: Function selector button > function
selector button > Map type.
Destination
The map shows you the destination. The destination is marked with
a chequered flag. The map is set to face north.
Position
The map depicts the vehicle's current location. The map scale and
map orientation settings are not changed.Overview
The entire route from the starting point to the final destination is
displayed on the map. The map scale varies according to the length
of the route. The map is set to face north.
Current position 3D
The map is shown in a 3D perspective (as seen from the current loca-
tion). The map is set automatically to face the direction of travel

page 118.
Applies to vehicles: with navigation system
Map content
– Select: Function selector button > function
selector button > Map content.
The display of map contents such as motorway exits or restaurants
can be switched on () and off.
Applies to vehicles: with navigation system
Voice guidance
– Select: Function selector button > function
selector button > Voice guidance.
You can switch the voice guidance cues on and off as desired.
Select the setting off (phone) to deactivate the spoken navigation
information only for the duration of a telephone call.
Applies to vehicles: with navigation system
Altitude display
– Select: Function selector button > function
selector button > Altitude display.
NAV
SETUP
NAV
SETUP
NAV
SETUP
NAV
SETUP
NAV
SETUP










Calling up traffic information121
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
Calling up traffic information
Introduction
If desired, your MMI system will inform you about the current traffic
situation both on the screen and audibly.
You are probably familiar with the traffic reports that most radio
stations transmit at regular intervals. Your MMI system automati-
cally records these reports
page 121 for up to an hour after the
MMI has been switched off. The Traffic Programme reception is indi-
cated by the TP symbol when the radio, the CD player or the Audi
music interface*
21) is switched on
page 58.
In addition, more and more radio stations transmit traffic messages
that are received automatically and inaudibly by your MMI system.
You can set the system to display these messages on your MMI
display. Another even more convenient function is that the MMI
system uses these reports when the dynamic navigation function is
activated to guide you around traffic obstructions such as conges-
tions whenever possible
page 117.
The reception of traffic messages is indicated by the TMC symbol at
the top of the display when the navigation mode is activated:
Calling up traffic reports (TP memo)
Traffic reports are stored along with the station name and
the time of transmission.
Important: The Traffic Programme function must be
switched on
page 58.
– Press the function selector button marked .
21)Still under development at the time of printing.
TMC symbolsExplanation
TMC symbol litTMC stations are available and the dynamic
navigation is switched on
page 117.
TMC symbol not
litTMC stations are available; the dynamic navi-
gation is switched off.
TMC symbol
crossed outTMC stations are not available; the dynamic
navigation is switched on.
TMC symbol
is not displayedTMC stations are not available; the dynamic
navigation is switched off.
Fig. 106 List of traffic
reports
INFO











Calling up traffic information123
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
Important: The system must be tuned to a traffic station

page 122, and a navigation DVD must be inserted in the
drive
page 14.
– Press the function selector button marked .
– If the list of traffic messages
page 122, fig. 108 does
not appear in the MMI display, press the function
selector button again. A list of traffic messages

page 122, fig. 108 will now appear in the MMI display.
– Turn the rotary pushbutton to mark an entry.
– Press the rotary pushbutton. Traffic information on the
entry will now be displayed.
– To display the next traffic message in the detail view, turn
the rotary pushbutton to Display next report and press to
confirm.
– To display the selected message on the map in the detail
view, turn the rotary pushbutton to Show report on map.
– Press the rotary pushbutton. The red hatched line shows
the stretch of road affected by the traffic obstruction

fig. 109.– To display the next traffic message on the map, press the
rotary pushbutton again.
When the route guidance is active, the TMC traffic messages which
are relevant for your route are shown with a red warning symbol and
are sorted by distance to your current location
page 122,
fig. 108. A traffic obstruction in the immediate vicinity will be shown
at the top of the list.
All other traffic messages are then shown with greyed-out warning
symbols and are sorted according to road category (motorways,
major roads, other roads) and road number.
Urgent traffic messages such as a car travelling in the wrong direc-
tion on the motorway are automatically displayed in the MMI
display. To cancel the report, simply press the button or
the rotary pushbutton.
When the route guidance is active, traffic messages are shown with
red warning symbols and are sorted according to road category
(motorways, major roads, other roads) and road number.
Other settings
Applies to vehicles: with TP memo timer
TP memo timer
– Select: Function selector button > function
selector button > TP memo timer.
You can set two times of day at which you want the MMI system to
record traffic reports. Use the Timer status option to activate and
deactivate the timers individually or together. You can set the time
by turning the rotary pushbutton to mark the timer and pressing to
confirm. Then turn the rotary pushbutton to change the time.
Switch from hours to minutes by pressing the rotary pushbutton.
Fig. 109 Displaying a
TMC traffic message
on the map
INFO
INFO
A1
RETURN
INFO
SETUP











Calling up traffic information125
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control











Basic operation 128
Basic operation
Applies to vehicles: with multi-function steering wheel
Introduction
You can use the multi-function steering wheel to call up
the following functions in the driver information system
one after the other: Navigation*, Telephone*, Radio, CD
player, Audi music interface* and TV*.
Using the multi-function steering wheel
fig. 110, you can operate
certain functions on the radio, the CD player, the Audi music inter-
face*
22), the TV*, the telephone* and the navigation system* very conveniently and without having to take your hands off the steering
wheel.
The available functions are displayed in the driver information
system
fig. 111. In addition, you can use the multi-function
steering wheel to switch the speech dialogue system* or the tele-
phone speech control system* on and off and to adjust the volume
on these systems.
These functions can be operated by pressing and scrolling buttons
to
fig. 110.
•Press the button repeatedly to switch between the
navigation* mode, the telephone* mode and the current audio
source. The selected function will appear in the display of the driver
information system
fig. 111. If a sub-menu is displayed in the
driver information system, you can exit this menu again by pressing
the button.
•Scroll the left thumbwheel to select an option within one of
the following functions: radio, CD, Audi music interface*22), TV*,
telephone* and navigation*.
•The speech dialogue system* and the telephone speech control
system* are activated by pressing the talk button . Press and hold
the talk button again to deactivate the speech dialogue / speech
control system.
•Scroll the right thumbwheel up/down to raise/lower the
volume as desired.
Note
•The on-board computer is also displayed in the driver informa-
tion system. Please refer to your Owner's Manual for a detailed
description.
Fig. 110 Controls on
the multi-function
steering wheel
Fig. 111 Display in the
driver information
system
22)Still under development at the time of printing.
A1A4
MODEA2
MODE
A1
A3
A4