2008 AUDI A4 AVANT fuel cap

llffll...__C_ h_ e_c _k _ i_n ..::g ,_ a_n_ d_ f_il _li _n....: g==---------------------------------------------­
Fig. 208 Illustra tion o f
principle 2: Markers on
oil dipstick
Before you check anything in the engine compartment,
always read and heed all WARNINGS => & in "Working in
the engine compartment" on
page 273.
Determining oil level
-Park your vehicle so that it is horizontally level.
- While at operating state temperature, briefly let the
engine run at idle and then shut
it off.
- Wait approx. two minutes.
- Pull out the oil dipstick . Wipe off the oil dipstick with a
clean cloth, and s lide it back in as far as it will go.
- Pull it back out and read off the oil level
=> page 277,
fig. 207 or=> fig . 208. Top off the engine oil, if applicable
=> page 278.
Oil level within range @
-Do not add oil.
Oil level within range ~
You can add oil. Afterwards, the oil level should be within
range @.
Oil level within range ©
-You must add oil. Afterwards, the oil level should be
within range @.
The oil level needs to be checked at regular intervals. The best times
to do this are whenever you refuel and prior to long trips. •
Adding engine oil 'l:::7:
Fig. 209 Oil filler cap
locat ion: 2.0 liter , 4-
cylinder turbo engine
...

___ T_ ir_e _ s_ a_ n
_ d_ w_ h_ e_ e_ls _________________________________________________ _
&, WARNING (continued)
crashes and serious personal injuries . Have worn or damaged tires
replaced immediately.
• Tires age even if they are not being used and can fail suddenly,
especially at high speeds. Tires that are more than 6 years old can
only be used in an emergency and then with special care and at
low speed.
Glossary of tire and loading terminology
Accessory weight
means the combined weight (in excess of those standard items
which may be replaced) of automatic transmission, power steering,
power brakes, power windows, power seats, radio, and heater, to
the extent that these items are available as factory-installed equip­
ment (whether installed or not).
Aspect ratio means the ratio of the height to the width of the tire in percent.
Numb ers of 55 or lower indicate a low sidewall for improved
steering response and better overall handling on dry pavement.
Bead means the part of the tire that is made of steel wires, wrapped or
reinforced by ply cords and that is shaped to fit the rim.
Bead separation
means a breakdown of the bond between components in the bead.
Cord
means the strands forming the plies in the tire.
&, WARNING (continued)
• Never mount used tires on your vehicle if you are not sure of
their "previous history." Old used tires may have been damaged
even though the damage cannot be seen that can lead to sudden
tire failure and loss of vehicle control.
• If you notice unusual vibration or if the vehicle pulls to one side
when driving, always stop as soon as it is safe to do so and check
the wheels and tires for damage.
•
Cold tire inflation pressure
means the tire pressure recommended by the vehicle manufacturer
for a tire of a designated size that has not been driven for more than
a couple of miles (kilometers) at low speeds in the three hour period
before the tire pressure is measured or adjusted .
Curb weight
means the weight of a motor vehicle with standard equipment
including the maximum capacity of fuel, oil, and coolant, air condi­
tioning and additional weight of optional equipment.
Extra load tire
means a tire designed to operate at higher loads and at higher infla ­
tion pressures then the corresponding standard tire. Extra load tires
my be identified as "XL", "xi", "EXTRA LOAD", or
"RF" on the side ­
wall.
Gross Axle Weight Rating ("GAWR")
means the load-carrying capacity of a single axle system, measured
at the tire-ground interfaces .
Gross Vehicle Weight Rating ("GVWR")
means the maximum total loaded weight of the vehicle.

___ T_ ir_e _ s_ a_ n
_ d_ w_ h_ e_ e_ls _________________________________________________ _
S idewa ll
means t hat port ion of a tire between the tread and bead.
Speed ra ting means t he speed at which a tire is designed to be driven for
extended periods of time. The ratings range from 93 mph (150 km/h)
to 186 mph (298
km/h) => page 306. You may not f ind this informa ­
tion on a ll tires because it is not required by law .
The speed rating letter code, whe re applicable, is mo lded on the tire
s idewal l and indicates the maximum perm issible road
speeds => &
in "Winter tires" on page 310.
Tire pr essu re m onitorin g sys tem *
means a system that detects when one or more of a vehicle's tires
are under inflated and i lluminates a low tire pressure warning te ll­
tale .
Tread
means that portion of a tire that comes into contact with the road.
Trea d sepa ration
mea ns pu lling away of the tread from the tire carcass.
Tr eadw ear indi cato rs ( TWI)
mea ns the projections with in the pr incipa l grooves designed to give
a visual indication of the degrees of wear of the tread . See
=> page 303, "T read Wear Indicator (TWI)" for m ore information on
measuring tire wear.
Uniform Tire Qualit y Grading
is a tire information system deve loped by the United States National
H ighway Traff ic Safety Admin istration (N HTSA) t hat is designed to
help buyers make relative comparisons among tires. The U TQG is
n ot a safety rating and not a guarantee that a tire will last for a
prescribed number of miles or perform in a certain way . It simply
gives ti re buyers additiona l info rmation to combine with other
considerations, such as price, brand loyalty and dea ler recommen -dations
. Under UTQG, tires are graded by the tire manufacturers in
t hree areas : treadwear, tract ion and tempera ture resista nce. The
U TQG information on the tires, molded into the sidewa lls .
U .S . D OT Tire Identification Number (TIN )
This is the tire's "seria l number" It begins with the letters "DOT" and
indicates that the tire meets a ll federa l standards. The next two
numbers or letters indicate the plant where it was manufactured,
and t he last four numbers represent the wee k and year of manufac ­
ture. For example,
DOT ... 2205 ...
means t hat the tire was produced in the 22t h week of 2005. The
other numbers are marketing codes that may or may not be used by
t he t ire manufacturer. This informat ion is used to c ontac t
consumers if a tire defect requires a reca ll.
Veh icle capacity we ight
means the rated cargo and luggage load plus 150 lbs . (68 kilograms)
t imes t he vehicle's total seating capaci ty as listed on the la bel
located either on the driver's side 8 -pillar or on the inside of the fuel
fi ller flap .
Vehi cle max imum l oad on th e tir e
means that load on an ind ividual tire that is determ ined by distrib ­
uting to each axle its share of the maximum loaded vehicle weight
and d ividing by two.
V ehi cle norm al l oa d on th e tir e
means that load on an ind ividual tire that is determ ined by d istrib ­
uting to each axle its share of the curb weight, accessory weight,
and normal occupant weigh t (distributed in accorda nce w ith tab le
below=> page 297) and dividing by two . _.,

________________________________________________ T_ i_ r _e _s _ a_n_ d_ w_ h_ e_e _l_s _ __._
O cc upant loading and distribution for vehicle no rmal load for various d esignated s eating capa cities
Designated seating capacity , num­
ber of occupants
5
Cold tire inflation pressure
Vehicle normal load , number of
occupants
3
Occupant distribution in a normally
loaded vehicle
2 in front, 1 in back seat
T ire pressure affec ts the overall ha ndling, performan ce and safety of a vehicle.
Fig . 21 7 Tire pre ssu re
label : located eit her on
driver's side B-pillar or
in side the fuel filler fl ap
ill
9 ,-, ~ ------------------.. j;l
• (SEATING CAPAQlY :rorAL I :FRONT I : cENTER I :REAR I ) m
Thea,mtwd""'9/Wdoocu,,.....andQ1Vo.....,.....,-,ed .logo, _ .,.
TIRE AND LOAD ING INFORMATION
TIRE SIZE COLO TIRE PRESSURE
FRONT -KPa, -PSI
REAR -KPa, - PSI
SPARE -KPa, -PSI
MANUAL FOR
INFORMATION SEE OWNER'S I
ADDITIONAL
Fig . 218 T ir e pr essu re
label
w arm tir e to matc h "cold t ire in flation press ure" recommenda tions .
The tires wou ld then be underinflated and cou ld fai l suddenly .
M aintaini ng proper t ire pressure is one of the most im po rta nt
thi ngs you ca n do t o help avo id sud den t ire fa ilu re. Underi nflated
tires are a major cause of sudden tire failure. Keeping tires at the
ri ght pressure is also importa nt for safe and r espo nsive ve hicle
handling, traction, braking and load carrying.
Tire pressures are
particularly important when the vehicle is being driven at higher
speed s, and then especially when heavily loaded even within the
•
T ire pressure generally refe rs to the amou nt of air in a t ire that it
needs it to do its job and safely carry the combined load of the entire
veh ic le and i ts c ontents. Tire p ressu re is measu red in kilopascals
(kPa), the international measuring unit and in pounds per square
inch (PSI) . Tir e p res su re is based in part on th e vehic le's design and
load lim it - the greatest amount of weight that the veh ic le can carry
safely and the tire size . The proper tire pressure is frequently
re ferred to as the "recommended cold t ire infla tion pressure." A ir in
the tires expands when the tire heats up because of internal friction
when it fl exe s i n us e. The tir e press ure is high er w he n th e t ire has
warmed up than when it is "cold." It is the inflation pressure in a "c old" tire that c ounts. Theref ore , yo u sho uld never le t air ou t of a
permissible load -carrying capacities approved for your vehicle. ...
Ve hic le care Technical data

___ T_ ir_e _ s_ a_ n
_ d_ w_ h_ e_ e_ls _________________________________________________ _
The recommended tire pressures for your Audi depend on the kind
of tires on your vehicle and the number of passengers and/or
amount of luggage you will be transporting.
The tire pressure label located either on driver's side 8-pillar or
inside the fuel filler flap on your Audi lists the recommended cold
tire inflation pressures for the vehicle at its maximum capacity
weight and tires that were on your vehicle at the time it was manu­
fac tured .
If you wish to improve comfort when operating the vehicle at
normal load (up to 3 occupants), you can adjust tire pressures to
those specified for normal vehicle load. Before operating the vehicle at maximum load, you must increase the tire pressures to those
specified for maximum vehicle load
~ & .
If your vehicle is equipped with a tire pressure monitoring system*,
bear in mind that the system can only monitor the tire pressures you have stored
. The system does not recognize the load condition of
your vehicle.
The effectiveness of the tire pressure monitoring system will be
impaired if you store normal load pressures but then operate the
vehicle at its maximum
load~& .
See the illustration~ page 297, fig . 217 for the location of the label
either on driver's side 8-pillar or inside the fuel filler flap (color of
the actual label and exact location on the vehicle will vary slightly).
Note that the following table is accurate at the time of going to
press and is subject to change . In the event of discrepancies, the tire
pressure label (e ither on driver's side 8 -pillar or inside the fuel filler
flap) always takes precedence.
The table below lists the recommended cold tire inflation pressures
for the Audi model covered by your Owner's Literature at the
vehicle's capacity weight and the tire si zes installed on the respec­
tive models as original equipment, or as a factory option.
Engine Tire size designation Tire pressure front Tire pressure rear
(displace- normal load normal load
ment in condition (up to full load
condition (up full load
liter) condition
condition
3 occupants) to 3 occupants)
PSI kPA PSI kPA PSI kPA PSI kPA
4-cylinder 215/55 R16 93H All Season 35 240
36 250 35 240
36 250
2.0
235/45 R17 94H All Season 33 230 35 240 33 230 35 240
235/45 R17 94V High Performance 30 210
32 220 30 210
32 220
235/40 R18 95V XL High Performance 35 240 39 270 35 240 39 270
6-cylinder 215/55 R16 93H All Season 36 250 36 250 35 240 36 250
3.2
235/45 R17 94H All Season 35 240
35 240
33 230 35 240
235/45 R17 94V High Performance 30
210 32 220 30 210 32 220
235/40 R18 95V XL High Performance 38 260 42 290 38 260 42 290
XL = reinforced or extra load tire. It may also appear as xi, EXTRA LOAID, or RF on the tire sidewall.

___ T_ ir_e _ s_ a_ n
_ d_ w_ h_ e_ e_ls _________________________________________________ _
The tire pressure label on your Audi lists the recommended cold tire
inf lation pressures for the new, original equipmen t tires that were
on your vehic le at the time it was manufactured . For the location of
the
labe l=> page 297, fig. 217 .
Most tires lose a ir natural ly over time. They can a lso lose some air if
you drive over a potho le or hit a curb wh ile parking. It is usually not
possible to see whether the radial t ires used today are under inflated
just by looking at them.
Therefore, be su re to check tire pressures at least once a month and
always before going on a long trip . Make sure to take the number of
people and the amount of luggage into account when adjusting tire
pressure for a trip -even one that you wou ld not cons ider to be
" long ."
See => page 301, "Tires and vehicle load limits" for more
important i nformation .
A lways use an accurat e tire pressure gaug e when checking and
adjusting inflat ion pressures. Check a ll of the tires and be sure not
to forget the spare tire . If the pressure in any tire is too high when
the t ire is "cold," let air o ut of the t ire slowly with the edge of the tire
gauge and keep check ing the pressure until you reach the pressure
that is correct for the load (passengers and luggage) and kind of
driving you p lan to do .
I f the pressure in any tire is too low, note the difference between the
pressure in the co ld tire and the pressure you need and add the air
that you need to reach the correct pressure for the vehicle load
(passengers and luggage) fo r the t ires on your veh ic le as listed on
the on your vehicle and in this manual and the kind of driving you pl an to do .
Never exceed the m aximum inflation pressure li sted on the tire
s idewall for an y re ason .
Remem ber that the vehic le manufacturer, not t he tire manufacturer,
determines the correct tire pressure for the tires on your vehicle .
I t is important to check the tire pressure when the tires are cold.
• Read the required tire pressure from the t ire pressure label
located either on driver 's side B -pillar or inside the fuel fi ller flap . •
Turn the va lve stem cap counter -clockwise to remove it from the
t ire valve .
• Place the air pressure gauge on the valve.
• The tire pressures should only be checked and adjusted when
the tires are cold. The s lightly raised pressures of warm tires must
not be reduced.
• Adjust the tire pressure to the load you are carrying.
• Reinstal l the va lve stem cap on the valve .
When should I check the tire pressure?
The correct tire pressure is especially important at high spe eds . The
pressure should the refore be checked at least once a mo nth and
a lways before starting a journey. Do not forget to check the tire pres ­
sure for the spare whee l
=> page 317.
Wh en should I adjust th e tir e pre ssur es?
Adjust t he tire pressure to the load you are carry ing . After changing
a wheel
o r replacing whee ls you have to ad just the tire pressures on
a ll whee ls . In addition, on vehicles w ith tire pressure monito ring
system* you must then store the new tire pressures in the system
=> page 45.
& WARNING
Incorrect tire pre ssure s and /or underinflation can lead sudden tire
f ai lure , loss of control , collision , seri ous per sonal injury or even
death.
• When the w arning symbol
(l) appe ars in the in strument
clu ster , stop and inspect the tire s.
• Incorrect t ire pres sure and /or underinflat ion can cause
increa sed tire wear and can affect the handling of the vehicle and
s topping ability.
• Incorrect tire pres sures and /or underinflation can also lead to
s udden tire fa ilure , inc luding a blowout and sudden defl ation ,
cau sing los s of vehicle control .
~

________________________________________________ T_ i
_ r_e _s_ a_n_ d_ w_ h_ e_e _ l_s __ l'III
& W ARNING (continued )
• The driver is respon sible for the correct tire pre ssure s for all
tire s on the vehicle. The applicable pressure values are located on
a st icker on the driver 's side B-pillar or on the inside of the fuel
filler flap.
• Only when all tire s on the vehicle are filled to the correct pres­
sure , the tire pressure monitoring system * can work correctly .
• The use of incorrect tire pressure values can lead to accidents
or other damage. Therefore it is essential that the driver observe
the specified tire pressure values for the tires and the correct pres­
sures for the function of the tire pressure monitoring system*.
• Always inflate tires to the recommended and correct tire pres ­
sure before driving off.
• Driving with underinflated tires bend more , letting them get
too hot resulting in tread separation , sudden tire failure and loss
of control.
• Ex cessive speed and /overloading can cause heat build -up ,
sudden tire failure and loss of control .
• If the tire pressure is too low or too high, the tires will wear
prematurely and the vehicle will not handle well.
• If the tire is not flat and you do not have to change a wheel
immediately, drive at reduced speed to the nearest service station
to che ck the tire pressure and add air as required .
0 Note
Driving without valve stem caps can cause damage to the tire
valves. To preve nt th is, a lways make s ure th at f acto ry installed va lve
stem caps on al l whee ls are securely mounted on the va lve .
~ For the sake of the environment
Underinflated tires will a lso increase the fuel consumpt io n. •
Tires and vehicle load limits
There are limits to the amount of load or weight t hat any vehic le and
any tire can carry . A ve hicle that i s ove rloa ded will not handle well
and is more d iff icu lt to stop . Overload ing can not only lead to loss
o f vehi cle control, but can also damag e impor tan t p arts o f the
vehic le and can lead to sudden tire failure, including a blowout and
sudde n defla tion that ca n cause the veh ic le to c ra sh .
Your sa fety a nd t hat o f your passe ngers a lso depe nds o n maki ng
s u re that load li mits are not exceeded. Vehic le load incl udes every ­
b ody and everythi ng i n and on t he vehicle . T he se l oa d limi ts are
technical ly referred to as the ve hic le's
Gross Vehicle Weight Rating
("GVW R"l.
T he "GVWR" includes the wei ght of the basic vehic le, all factory
in sta lled acces so ries, a full t an k of f uel, o il, c oolant a nd oth e r flu ids
p lus max imum load . T he maximum load inc ludes th e number o f
p asse ngers tha t th e ve hicle i s intended t o carry ("seat ing ca paci ty")
with an assu med weight o f 150 l bs (68 kg) fo r each passe nger at a
designated seating position and the total weight of any luggage in
th e v ehic le. I f you tow a trai ler, the we ig ht o f the tra iler hitch a nd th e
tongue weight of the loaded trailer must be inc luded as part of the
ve hicle lo ad .
The
Gross Axle Weight Rating ("GAWR") is t he maximum load that
ca n b e app lie d at eac h of th e veh icle's two axle s.
T he G ross Ve hicle We ight Rati ng a nd th e G ross A xle Wei ght R ati ng
are listed on the safety comp liance stic ker label located either on
t he driver 's si de B-pi lla r o r on the in sid e of t he fue l fille r fl ap. You r
Aud i has 5 seating posit ions, 2 in the front and 3 in the rear for total
sea ting ca paci ty of 5. Each sea ting p osit ion has a safe ty b elt
=> page 176, "Saf ety be lts" .
The fact that there is an upper limit to your vehicle's Gro ss Vehicle
W eight Rat ing m eans that th e total weight o f whatever is b ein g
carried in the vehic le (including the weight of a traile r hitc h and the
ton gue we ight of the loaded tr aile r) is lim it e d. Th e m or e passe ng ers
~
Vehicle care

___ T_ ir_e_ s_ a_ n
_ d_ w_ h_ e_ e_l_
s _________________________________________________ _
R ep laci ng tires a nd whee ls
T ires shou ld be replaced at least in pairs and not ind ividually (for
examp le bo th front tires or both rear tires together!.
On v ehicles with tire pressure monitoring system *, be sure to read
and heed the informat ion
=> page 307.
A lways buy rep lacement radia l tires that have the same sp ecifica­
t ions as the tires approved for your veh ic le by Aud i. Replacement
tires must always have the same load rating specification as the
orig ina l equipment or approved optional t ires listed in the table
=> page 297.
Audi -approved specification tires are specially matched to your
vehic le and its load limits, and can contribute to the important road­
holding, driving characteristics, and safety of the vehicle . The table
(=> page 297) lists specifications of the tires approved for the Audi
models covered by your Owner's Literature .
The tire pressure labe l located either on driver 's side 8 -pi llar or
inside the fuel fi ller
flap(=> page 297, fig. 218) lists the specifica ­
tions of the origina l equipment tires installed on your vehicle at the
time it was manufactured .
Federa l law requires tire manufacturers to place standardized infor ­
mation on the s idewall of all
tires => page 305, fig. 221 . This informa ­
tion identifies and describes the fundamental characteristics, the quality grade of the tire and a lso provides a tire identification
number for safety standard certification and in case of a recall.
Tir e specificat ions
Knowledge of tire specifications makes it easier to choose the
correct tires . Ra dial t ires have the tire specifications marked o n the
sidewall, for example :
P235 / 45 R 1 7 94 H
This contains the following informat ion:
P Indicates the tire is for passenger cars (where app licable)
2 35 No minal t ire wid th i n mm of the tire fro m sidewall edge to side ­
wall edge. In general, the larger the number, the wider the tire
45 Height/width ratio in percent (aspect ratio)
R Tire construction: Radial
17 Rim diameter code (in inches)
94 Load rat ing code
H Speed rating letter code
X L (or "xi", "EXTRA LOAD" or "RF") indicates that the t ire is a "Rein­
forced" or an "Extra Load" ti re
M +S (or "M/S") Ind icates that the tire has some mud and snow capa -
bility
The tires cou ld also have the information of direction of rotation
=> page 293.
Tire m anuf acturing date
The manufacturing date is a lso indicated on the tire sidewall
(possibly on ly on the
inner side of the wheel):
"DOT ... 2205 . ..
" means, for example, that the tire was produced in
the 22th week of 2005.
S peed r ating (le tt e r code )
The speed rating letter code on the whee ls indicates the maximum
permissible road
speeds => & in "W inter tires" on page 310 .
p up to 93 mph ( 150 km/h)
Q up to 99 mph (158 km/h)
R up to 106 mph (170 km/h)
s up to 110 mph (180 km/h)
T up to 118 mph (190 km/h)
u up to 124 mph (200 km/h)
H up to 130 mph (210 km/
h)
V up to 149 mph (240 km/h)3
l
z over 149 mph (240 km/h)31
3> For tires w ith a maximum speed capabi lity over 149 mph (240 km/h) , tire
manufacturers sometimes use the letters " ZR."