2008 Alfa Romeo GT steering

IN AN EMERGENCY
181
STARTING BY INERTIA
If the car is equipped with “Kit for tyre re-
pair Fix&Go“, see the instructions contained
in the following chapter.
GENERAL INSTRUCTIONS
As an alternative to the FIX & GO, the car
can be provided (upon request) with space-
saver spare wheel or standard wheel; wheel
changing and correct use of the jack call for
some precautions as listed below.
IN THE EVENT OF A PUNCTURE
Never push, tow or coast
start the car. This could
cause fuel to flow into the
catalyst damaging it irreversibly.
Remember that the en-
gine brake and power
steering are not opera-
tional until the engine is started,
therefore, much greater effort than
usual is needed on the brake ped-
al and steering wheel.
Signal the presence of the
stationary car according to
current regulations: hazard
warning lights, reflecting triangle
etc.. Any passengers should leave
the car and wait for the wheel to be
changed out of harm of the traffic.
If parked on a slope or rough sur-
face, chock the wheels with
wedges or other suitable devices
to prevent the car from rolling.
Never start the engine
with the car jacked.
When driving with a trail-
er, disconnect the trailer before
raising the car. The compact spare
wheel is specific to your car, do not
use it on other models, or use the
spare wheel of other models on
your car.
Should the type of wheels used
be changed (alloy rims instead of
steel), it is also necessary to
change the whole set of fastening
bolts with others of suitable size.
The compact spare wheel is nar-
rower than normal wheels, it
should be used only for the dis-
tance necessary to reach a service
point to have the punctured tyre
repaired and, during its use, the car
speed must not exceed 80 km/h.

Volumetric sensors
ESP system sensor
Steering angle sensor
EOBD system diagnosis socket
Cell phone provision
Driver’s door control unit supply
Passenger’s door control unit supply
Control lighting
Climate control system control lighting
Instrument cluster
Instrument cluster
Driver’s door control unit
ABS control unit
ABS control unit
Dashboard control unit
Air - bag control unit
Electronic injection control unit +30
Engine compartment control box (petrol versions)
Dashboard control unit
Trailer control unit15
7.5
7.5
15
15
20
20
7.5
7.5
10
10
15
7.5
50
50
7.5
7.5
125
70
10 F39
F42
F42
F39
F39
F47
F48
F49
F35
F37
F53
F39
F42
F04 (MAXI-FUSE)
F02 (MAXI-FUSE)
F50
F18
F70 (MEGA-FUSE)
F71 (MAXI-FUSE)
F36 52
52
52
52
52
52
52
52
52
52
52
52
52
53
53
52
53
54
54
52
SERVICES FIGURE FUSE AMPERES
IN AN EMERGENCY
210

IN AN EMERGENCY
213
IF THE CAR IS TO BE TOWED
The tow ring supplied with the car is
housed in the tool box under the boot mat.
To install the tow ring, proceed as follows:
– Take the tow ring from the tool box.
– Remove the cover (A) snap-fitted on
the front (fig. 55) or rear (fig. 56)
bumper. To do this, using the flat-bladed
screwdriver provided, protect the tip with a
soft cloth to avoid damaging the car.– Firmly screw the ring in its housing.
fig. 55 - front
A0A0650b
fig. 56 - rear
A0A0670b
Before tightening the ring
carefully clean the thread-
ed housing. Before begin-
ning to tow the car, make sure that
the ring is firmly tightened in its
threaded housing.
Before starting to tow,
turn the ignition key to
MAR and back to STOP,
again without removing it. Re-
moving the key automatically en-
gages the steering lock resulting in
the impossibility to steer the
wheels. When towing remember
that without the help of the engine
brake and power steering greater
effort is required on the pedal and
steering wheel. Do not use flexible
cables for towing and avoid jerks.
During towing operations make
sure that fastening the joint to the
car does not damage the compo-
nents in contact with it. When tow-
ing the car, it is compulsory to fol-
low specific traffic regulations con-
cerning both the towing device and
behaviour on the road.

CAR MAINTENANCE
219
ADDITIONAL
OPERATIONS
Every 1000 kmor before long journeys,
check and if necessary top up:
– engine coolant fluid level
– brake/hydraulic clutch control fluid level
– power steering fluid level
– windscreen washer and headlamp wash-
er fluid level
– tyre pressure and conditions.
Every 3000 kmcheck and if necessary
top up the engine oil level.
The use of FL Seleniaproducts is rec-
ommended which have been designed and
made expressly for Alfa Romeo cars (see
“Refuelling” in the “Technical Specifica-
tions” chapter).
ANNUAL INSPECTION
PROGRAMME
For cars with an annual mileage
of below 20,000 km (for example
about 10,000 km) the following
yearly inspection programme is ad-
vised:
– Check tyre conditions/wear and if nec-
essary adjust the pressure (including spare
wheel)
– Check operation of lighting system
(headlights, direction indicators, hazard
warning lights, boot, passenger compart-
ment, glovebox lights, warning lights, etc.)
– Check operation of windscreen wiper
system, spray jet adjustment
– Check windscreen blade position/wear
– Check front disk brake pad conditions
and wear
– Check cleanness of bonnet and boot
locks, and lever cleanness and lubrication.– Sight check for conditions of: engine,
gearbox, transmission, pipes (exhaust - fu-
el supply - brakes), rubber parts (boots -
sleeves - bushes etc..), brake and fuel sup-
ply system hoses
– Check battery charge
– Sight check for conditions of various dri-
ve belts
– Check and if necessary top up fluid lev-
els (engine coolant, brakes, windscreen
washer, battery etc. )
– Change engine oil and oil filter
– Change pollen filter.

CAR MAINTENANCE
222
fig. 1 - 1.8 T. SPARK version
A0A0736b
A0A0681b
CHECKING LEVELS
Never smoke while work-
ing in the engine compart-
ment; gas and inflammable
vapours may be present, with the
risk of fire.
When topping up take
care not to confuse the var-
ious types of fluids: they
are incompatible with one anoth-
er and could seriously damage the
car.
fig. 2 - 2.0 JTS version 1Engine oil - 2Battery - 3Brake fluid -
4Windscreen/rear window/headlight
washer fluid - 5Engine coolant - 6Power
steering fluid - 7Selespeed transmission oil
(2.0 JTS Selespeed versions)

CAR MAINTENANCE
223
A0A0396b
fig. 4 - JTD 16V version1Engine oil - 2Battery - 3Brake fluid -
4Windscreen/rearscreen/headlamp wash-
er fluid - 5Engine coolant fluid - 6Power
steering fluid
A0A0683b
fig. 3 - 3.2 V6 version 1Engine oil - 2Battery - 3Brake fluid -
4Windscreen/rear window/headlight
washer fluid - 5Engine coolant - 6Power
steering fluid

CAR MAINTENANCE
227
Oil consumption is very
low; if topping up again is
needed shortly afterwards,
have the system checked for pos-
sible leaks by Alfa Romeo Autho-
rised Services.Do not allow the power
steering fluid to touch hot
parts of the engine: it is in-
flammable.
fig. 12
A0A0217b
fig. 11
A0A0400b
BRAKE AND HYDRAULIC
CLUTCH FLUID
(fig. 12)
Check that the fluid level in the reservoir
is at maximum. Top up with the brake fluid
specified in the table “Fluids and lubricants”
(see section “Technical specifications").
NOTEClean accurately the tank cap A
and the surrounding surface. When opening
the cap take the utmost care to prevent im-
purities entering the tank. When topping up,
always use a funnel with built-in filter with
mesh equal to or lower than 0.12 mm.
IMPORTANTFor this operation it is
however recommended to contact Alfa
Romeo Authorised Services.
POWER STEERING FLUID
(fig. 11)
Check that the level of the oil in the reser-
voir is at maximum.
This operation should be carried out with
the car on a level surface and the engine
switched off and cold.
Check that the level reaches the MAX
mark on the reservoir or coincides with the
upper notch (maximum level) on the dip-
stick (A) integral with the reservoir cap.If the oil level in the reservoir is below the
specified one, top up only with one of the
products listed in the “Fluids and lubricants”
table in the “Technical specifications” chap-
ter proceeding as follows:
– Start the engine and wait for the oil lev-
el in the reservoir to stabilise.
– With the engine running, turn the steer-
ing wheel lock to lock a few times.
– Top up to the MAXlevel notch, then
refit the cap.

CAR MAINTENANCE
234
Alloy rim painting involv-
ing temperatures exceed-
ing 150 °C should be
avoided since wheel mechanical
characteristics could be impaired. Do not cross switch the
tyres, moving them from
the right of the car to the
left and vice versa.Excessive low pressure
causes overheating of the
tyre with the possibility of
serious damage to it.Remember that car road
holding also depends on
correct tyre inflation pres-
sure.
RUBBER HOSES
As far as the brake system and fuel sup-
ply rubber hoses are concerned, carefully fol-
low the Scheduled Maintenance Pro-
gramme. Indeed, ozone, high temperatures
and the prolonged lack of fluid in the sys-
tem may cause hardening and cracking of
the hoses, with possible leaks. Careful con-
trol is therefore necessary.
IMPORTANT NOTES
– Where possible, avoid sudden braking,
tyre squealing starts, violent bumps against
kerbs, potholes or obstacles of various kinds.
Prolonged driving on rough roads may dam-
age the tyres;
– Routinely check the tyres for cuts on the
sides, swellings or uneven tread wear. If nec-
essary contact Alfa Romeo Authorised Ser-
vices;
– Avoid overloading the car when travel-
ling: this may cause serious damage to the
wheels and tyres;
– If a tyre is punctured, stop immediate-
ly and change it to avoid damage to the tyre
itself, the rim, suspensions and steering sys-
tem;
– Tyres age even if they are not used
much. Cracks in the tread rubber are a sign
of aging. In any case, if the tyres have been
on the car for over 6 years, they should be
checked by specialised personnel, to see if
they can still be used. Also remember to
check the compact spare wheel;
– In case of replacement, always fit new
tyres, avoiding those of dubious origin;