2008 Acura TSX lock

This indicator has three f unctions:Itcomesonasareminderthatyou
have turned off the vehicle
stability assist (VSA) system.
It flashes when VSA is active (see
page ).
It comes on along with the VSA
system indicator if there is a
problem with the VSA system.
You will also see a ‘‘CHECK VSA
SYSTEM’’ message on the multi-
inf ormation display (see page ).
This indicator normally comes on f or
a f ew seconds when you turn the
ignition switch to the ON (II)
position. For more inf ormation, see
page . When you press the hazard warning
button, both turn signals blink. All
turn signals on the outside of the
vehicle should f lash.This indicator normally comes on f or
a f ew seconds when you turn the
ignition switch to the ON (II)
position. If this indicator comes on at
any other time, there is a problem in
theABS.If thishappens,takethe
vehicle to your dealer to have it
checked. With this indicator on, your
vehicle still has normal braking
ability but no anti-lock f unction. You
will also see a ‘‘CHECK ABS
SYSTEM’’ message on the multi-
inf ormation display (see page ).
For more inf ormation, see page .
The lef t or right turn signal indicator
blinks when you signal a lane change
or turn. If an indicator does not blink
or blinks rapidly, it usually means
one of the turn signal bulbs is
burned out (see pages and ).
Replace the bulb as soon as possible,
since other drivers cannot see that
you are signaling.
1.
2.
3.
83
82
268
268 304 306
261
Instrument Panel Indicators
Turn Signal and
Hazard Warning
Indicators
VSA A ctivation Indicator
A nti-lock Brake System
(A BS) Indicator
Inst rument s and Cont rols
65
——
y
y
(yy
2008 TSX

The multi-inf ormation display in the
instrument panel displays various
inf ormation and messages when the
ignition switch is in the ON (II)
position. Some of the messages help
you operate your vehicle more
comf ortably.
Others help to keep you aware of the
periodic maintenance your vehicle
needs f or continued trouble-f ree
driving.When you turn the ignition switch to
the ACCESSORY (I) position, the
display shows ‘‘Goodbye.’’
There are three types of messages;
normal display messages, engine oil
lif e and maintenance messages, and
system messages.
You can also customize some vehicle
control settings to your liking with
the multi-inf ormation display and the
two buttons on the steering wheel
(see page ).
When you unlock and open the
driver’s door with the remote
transmitter, the display shows
‘‘Welcome Driver 1’’ or ‘‘Welcome
Driver 2’’ depending on which
remote transmitter you use. The
driver’s ‘‘ID’’ is detected by the
transmitter. For more information
about driver’s ‘‘ID’’, see page .If you use the key to unlock the
driver’s door, the display only shows
‘‘Welcome.’’ This means the system
cannot recognize either ‘‘Driver 1’’ or
‘‘Driver 2.’’ In this case, you cannot
use the customized settings on the
multi-inf ormation display (see page
).
86
13286
CONT INUED
Normal Display Messages
Multi-Inf ormation Display
Inst rument s and Cont rols
69
\f—\f—
y
y
(\fy\f\fy
2008 TSX

If you leave the key in the ignition
switch in the LOCK (0) or
ACCESSORY (I) position and open
the driver’s door, you will see
‘‘REMOVE KEY’’ on the display and
hear a reminder beeper.If the brake f luid level is at or below
theMINmarkonthesideof the
brake f luid reservoir in the engine
compartment, you will see ‘‘BRAKE
FLUID LOW.’’ If you see this
message, have the brake system
checked by your dealer (see page
). If thefuelfillcapismissingornot
tightened properly, you will see
‘‘TIGHTEN FUEL CAP.’’ Make sure
the fuel cap is installed and tightened
at least one click.
300
CONT INUED
Multi-Inf ormation Display
Remove Key Brake Fluid LowTighten Fuel Cap
Inst rument s and Cont rols
79
U.S.Canada
\f—\f—
y
y
(\fy\f\fy
2008 TSX

If there is a problem in the anti-lock
brake system (ABS), you will see
‘‘CHECKABSSYSTEM’’onthe
multi-inf ormation display. If you see
this message, have your vehicle
checked by a dealer (see page ).
If there is a problem with the
automatic transmission, you will see
‘‘CHECK TRANSMISSION’’ on the
multi-inf ormation display. Avoid
rapid acceleration, and have the
transmission checked by a dealer as
soon as possible. If there is a problem with your f ront
airbags, side airbags, passenger’s
side airbag automatic cutoff system,
automatic seat belt tensioners, side
curtain airbags, driver’s seat position
sensor, or the f ront passenger’s
weight sensors, you will see
‘‘CHECK AIRBAG SYSTEM’’ on the
multi-inf ormation display. Take your
vehicle to a dealer as soon as
possible(seepage ).
32
261Automatic transmission:
CONT INUED
Check T ransmission
Check A BS Syst emCheck A irbag Syst em
Multi-Inf ormation Display
Inst rument s and Cont rols
83
\f—\f—
y

y
(\fy\f\fy
2008 TSX

You can customize some vehicle
control settings f or ‘‘DRIVER 1’’ and
‘‘DRIVER 2’’ separately.
To have the driver’s ID detected,
make sure you use your transmitter
to unlock the driver’s door.
If you use the key to unlock the
driver’s door, the system cannot
recognize either ‘‘DRIVER 1’’ or
‘‘DRIVER 2.’’ In this case, when you
try to enter the customizing mode,‘‘DRIVER UNKNOWN
CUSTOMIZE IMPOSSIBLE’’ will be
displayed, and you cannot customize
some of the settings.
Refertothetableonpagetosee
what settings you can customize.
If you use your remote transmitter to
unlock the driver’s door, and the
system f ails to recognize either
‘‘DRIVER 1’’ or ‘‘DRIVER 2’’ see
page to link your transmitter to
your vehicle.
To use the system, your cell phone
and the HFL system must be linked.
Not all cell phones are compatible
with this system. Ref er to page
for instructions on how to link
your cell phone to the HFL and how
to receive or make phone calls, or
visit the acura.com/handsfreelink
website.
With the ignition switch in the ON
(II) position, press and hold the
INFO button for more than 3
seconds. ‘‘CUSTOMIZE ENTRY’’
appears on the multi-inf ormation
display. 219
88
132
Multi-Inf ormation Display
Customized Settings
86
DRIVER’S
ID
\f—\f—
y
y
(\fy\f\f
y
2008 TSX

Î
ÎÎ
Î
Î Î
Î Customize Setup
15 sec
30 sec
60 sec
0sec
15 sec
30 sec
60 sec
DRIVER DOOR
ALL DOORS
ON
OFF
30 sec
60 sec
90 sec
WITH VEH SPD
INTERMITTENT Page
106
108
111
113
115
117
Customize Menu
INTERIOR LIGHT
DIMMING T IME
HEADLIGHT AUT O OFF
TIMER
DOOR LOCK MODE
KEYLESS LOCK
ACKNOWLEDGEMENT
SECURITY RELOCK
TIMER
FRONT WIPER ACTION Description
Changes how long (in seconds) the
interior lights stay on after you close the
doors.
Changes how long (in seconds) the
exterior lights stay on after you close the
driver’s door.
Changes which doors unlock with the
remote transmitter when the button is
pushed one time.
The exterior lights flash each time you
press the LOCK or UNLOCK button. A
horn will also sound when you press the
LOCK button twice.
Changes how long it takes (in seconds)
for the doors to relock and the security
system to set after you unlock but do not
open the door.
Changes the windshield wiper operation
between two settings when the wiper
switch is in the INT position.
Customize Group
LIGHTING SETUP
(P.106)
DOOR · WINDOW
SETUP
(P.110)
WIPER SETUP
(P.117)
Customize Entry
CHG SETTING
(P.92)
: Default setting
Multi-Inf ormation Display
Inst rument s and Cont rols
89
——
y

y
(yy
2008 TSX

There are three custom settings in
the Door · Window Setup:DOOR LOCK MODE
KEYLESS LOCK
ACKNOWLEDGEMENT
SECURITY RELOCK TIMER
While the multi-information display
shows ‘‘DOOR · WINDOW SETUP,’’
press the SEL/RESET button on the
steering wheel. Each time you press
the INFO button, the display
changesasshowninthenext
column.
To customize a setting, press the
INFO button repeatedly until you see
the setting you want to customize,
and press the SEL/RESET button.
Then f ollow the procedures
described on the f ollowing pages. Door · Window Setup
Multi-Inf ormation Display
110
: Press the INFO Button.
——
y


y
(y

y
2008 TSX

While the multi-information display
is showing ‘‘DOOR · WINDOW
SETUP,’’ press the SEL/RESET
buttononthesteeringwheel.The
display changes to ‘‘DOOR LOCK
MODE’’ as shown above.Press the SEL/RESET button. The
display changes as shown above.
In def ault setting, if you push the
UNLOCK button once on the remote
transmitter or turn the key clockwise
in the driver’s door lock, only the
driver’s door unlocks.
You can select whether only the
driver’s door unlocks or all the doors
unlock in ‘‘DOOR LOCK MODE.’’
Select ‘‘DRIVER DOOR’’ or ‘‘ALL
DOORS’’ by pressing the INFO
button, and enter your selection by
pressing the SEL/RESET button.
CONT INUED
Door L ock Mode
Multi-Inf ormation Display
Inst rument s and Cont rols
111
\f—\f—
y
\f
y
(\fy\f

y
2008 TSX