2008 Acura TL lock

Pour the f luid slowly and caref ully so
you do not spill. Clean up any spill
immediately; it could damage
components in the engine
compartment.
Always use Honda Power Steering
Fluid. You may use another power
steering f luid as an emergency
replacement, but have the power
steering system f lushed and ref illed
with Honda PSF as soon as possible.
A low power steering f luid level can
indicate a leak in the system. Check
the f luid level f requently, and have
the system inspected as soon as
possible.
Check the level on the side of the
reservoir when the engine is cold,
and the engine compartment right-
side cover is of f (see page ). The
f luid should be between the UPPER
LEVEL and LOWER LEVEL. If not,
add power steering f luid to the
UPPER LEVEL mark.
The f luid level should be between
theMINandMAXmarksontheside
of the reservoir. If it is not, add
brake f luid to bring it up to that level.
Use the same fluid specified for the
brake system.
A low f luid level can indicate a leak
in the clutch system. Have this
system inspected as soon as possible. 286
Manual Transmission only
Clutch Fluid
Clutch Fluid, Power Steering Fluid
296
LOWER LEVELUPPER LEVEL
MAX
MIN
Turning the steering wheel to f ull lef t
or right lock and holding it there can
damage the power steering pump.
\f—\f—
y

y
(%\fy\f\f
y
2008 TL

Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
(Driver’s side)
Install the upper part of the air
intake duct.
(Driver’s side)
Install the engine compartment
corner cover, and secure it with
two fastener pins.
Install the engine compartment
side cover.Start the engine. If you are
replacing a driver’s side bulb, turn
the steering wheel all the way to
theright.If youarereplacinga
passenger’s side bulb, turn the
steering wheel to the lef t. Turn of f
the engine.
Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb by turning it one-
quarter turn counterclockwise. Turn on the lights to test the new
bulb.
4.
5.
6.
7.
8.
9.
2.
3.
1.
Replacing the Front T urn Signal/
Parking L ight Bulb
Lights
298
\f—\f—
y

y
(%\fy\f\fy
2008 TL

Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.Remove the bulb f rom the socket
bypushingitinandturningit
counterclockwise until it unlocks.
Install the new bulb in the socket.
Turn it clockwise to lock it in place.
Insert the socket into the
headlight assembly. Turn it
clockwise to lock it in place.
Test the lights to make sure the
new bulb is working.
Use a f lat-tipped screwdriver to
remove the holding clips f rom the
edge of the inner f ender cover,
and pull the inner f ender cover
back. Push the inner f ender cover in
place. Install the holding clips, and
lock them in place by pushing on
their center.
Start the engine. If you are
replacing a driver’s side bulb, turn
the steering wheel all the way to
theright.If youarereplacinga
passenger’s side bulb, turn the
steering wheel to the lef t. Turn of f
the engine.
3.
2. 4.
5.
6.
7.
8. 1.
CONT INUED
Lights
Replacing a Front Fog L ight Bulb
Maint enance
299
\f—\f—
y

y
(%\fy\f\fy
2008 TL

Remove the socket by turning it
one-quarter turn counterclockwise.
Open the trunk.
Using a small screwdriver, pop up
the pin in the center of the
f astener, then remove the f astener.
Unscrew and remove the cargo
net hook f rom the f ender. Pull
back the trunk lining.
Push the inner f ender cover in
place. Install the holding clips, and
lock them in place by pushing on
their center.
Turn on the f og lights to test the
new bulb.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Remove the bulb by turning it
about one-quarter turn
counterclockwise.
Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Use a f lat-tipped screwdriver to
remove the holding clips f rom the
edge of the inner f ender cover,
and pull the inner f ender cover
back. 3.
2. 4.
5.
6.
7.
8.
1.
2.
Replacing the Rear Turn Signal
Bulb (in Fenders)
Lights
300
Halogen bulbs get very hot when lit. Oil,
perspiration, or a scratch on the glass
can cause the bulb to overheat and
shatter.
\f—\f—
y
\fy
(%\fy\f\fy
2008 TL

Insert the fastener into the hole on
the side of the trunk lining, and
push in the head of the f astener.
Screw the cargo net hook into the
f ender.Determine which back-up light
is out (lef t or right), then open
the trunk.
Reinstall the trunk lining. Make
sure it is installed under the edge
of the trunk seal.
Testthelightstomakesurethe
new bulb is working.
Reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
3.
4.
5. 6.
7.
1a.
CONT INUED
Replacing the Back-up L ight Bulb
(in T runk L id)
Lights
Maint enance
301
CORNER
FASTENER
TRUNK LID
INNER
HANDLE
LEFT SIDE FASTENER
CORNER
FASTENER LEFT STOP RIGHT STOP
\f—\f—
y


y
(%\fy\f\fy
2008 TL

Popupthepininthecenterof
the lef t or right corner f astener
with a small screwdriver, and
remove the fastener.Remove the lef t side
f astener the same way.
Pull out the outside edge of the
rubber stop, then push the stop
outward, and pull it to remove it.
Remove the screw from the
trunk lid inner handle, and
removethehandletrim.
Pull back the corner of the
trunk lid lining.Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
c.
b.
2.
3.
d.
e.
Lef t side
only:
Lights
302
\f—\f—
y

y
(%\fy\f\fy
2008 TL

Insert the socket into the light
assembly. Turn it clockwise to
lock it in place.
Testthelightstomakesurethe
new bulb is working.
Reinstall the trunk lid lining. Make
sure it is installed under the edge
of the trunk seal.
Install all removed parts.If your seat belts get dirty, use a sof t
brush with a mixture of mild soap
and warm water to clean them. Do
not use bleach, dye, or cleaning
solvents. Let the belts air-dry bef ore
you use the vehicle. Dirt build-up around the openings of
the seat belt anchors can cause the
belts to retract slowly. Wipe the
openings with a clean cloth
dampened in mild soap and warm
water or isopropyl alcohol.
4.
5.
6.
7. Cleaning the Seat Belts
Lights, Cleaning the Seat Belts
Maint enance
303
OPENING
\f—\f—
y
y
(%\fy\f\fy
2008 TL

Examine the new wiper blades. If
they have no plastic or metal
reinf orcement along the back
edge, remove the metal
reinf orcement strips f rom the old
wiper blade, and install them in
the slots along the edge of the new
blade.Slide the new wiper blade into the
holder until the tabs lock.
Slide the wiper blade assembly
onto the wiper arm. Make sure it
locks in place.
Lower the wiper arm down against
the windshield.
Disconnect the blade assembly
fromthewiperarmbypushingin
the lock tab. Hold the lock tab in
while you push the blade assembly
toward the base of the arm.
Remove the blade f rom its holder
by grabbing the tabbed end of the
blade. Pull up f irmly until the tabs
come out of the holder.
2. 3. 5.
4.6.
7.
Wiper Blades
Maint enance
305
BLADE
REINFORCEMENTBLADE
LOCK TAB
\f—\f—
y

y
(%\fy\f
\fy
2008 TL