2008 Acura TL ignition

µµ
µ
µ
The ignition switch has f our
positions: LOCK (0), ACCESSORY
(I), ON (II), and START (III).
You can insert or
remove the key only in this position.
To turn the key, you must push the
key in slightly. If your vehicle has an
automatic transmission, the shif t
lever must also be in Park. If the f ront wheels are turned, the
anti-theft lock may make it difficult
to turn the key. Firmly turn the
steering wheel to the lef t or right as
you turn the key.
You can
operate the audio system and the
accessory power sockets in this
position.
This is the normal key
position when driving. Several of the
indicators on the instrument panel
come on as a test when you turn the
ignition switch f rom the
ACCESSORY (I) to the ON (II)
position. You will hear a reminder beeper if
you leave the key in the ignition
switch in the LOCK (0) or the
ACCESSORY (I) position and open
the driver’s door. Remove the key to
turn of f the beeper.
If your vehicle has an automatic
transmission, the shif t lever must be
in Park bef ore you can remove the
key f rom the ignition switch.
Use this position
only to start the engine. The switch
returns to the ON (II) position when
you let go of the key.
LOCK (0) A CCESSORY (I)
ON (II)
ST A RT (III)
Ignition Switch
Inst rument s and Cont rols
95
Removing the key from the
ignition switch while driving
locks the steering. This can
cause you to lose control of the
vehicle.
Remove the key from the
ignition switch only when
parked.
\f—\f—
y
\fy
(%\fy\f
\f\fy
2008 TL

Each f ront door has a master door
lock switch. Either switch locks and
unlocks all doors. Push the bottom of
the switch to lock the doors and the
toptounlockthem.
Each door has a lock tab on the top.
Push the tab down to lock the door
and pull it up to unlock. When you
push down the lock tab on the driver’s
door, all the doors lock.All doors can be locked f rom the
outsidebyusingthekeyinthe
driver’s door. To unlock only the
driver’s door, insert the key, turn it,
and then release it. The remaining
doors unlock when you turn the key
a second time within a f ew seconds.
With the driver’s door open and the
key in the ignition, both master door
lock switches are disabled. If you try
to lock an open driver’s door by
pushing in the lock tab, all doors will
unlock when you close the driver’s
door.
To lock any door when getting out of
the vehicle, push the lock tab down,
and close the door.
L ockout Prevent ion
Door L ocks
96
\f—\f—
y
\fy
(%\fy\f
\f
y
2008 TL

µ
µ µ
µ
If you unlock the doors with the
remote transmitter, but do not open
anydoorswithin30seconds,the
doors automatically relock and the
security system sets. To change this
setting, ref er to Keyless Memory
Settings on page . Press this button once
to unlock the driver’s door or all the
doors (depending on the keyless
memory setting). Press it twice to
unlock the other doors. Some
exterior lights will f lash twice each
time you press the button.
The ceiling light (if the ceiling light
switch is in the center position) will
come on when you press the
UNLOCK button. If you do not open
anydoorswithin30seconds(or
whatever setting the relock timer is
set to), the light f ades out. If you
relock the doors with the remote
transmitter before 30 seconds have
elapsed, the light will go of f
immediately.
Press this button once to
lock all doors. Some exterior lights
will f lash. When you push LOCK
twice within 5 seconds (depending
on the keyless memory setting), you
will hear a beep to verify that the
doors are locked and the security
system has set. You cannot lock the
doors if any door is not f ully closed
or if the key is in the ignition switch. Pressthisbuttonfor
about 1 second to open the trunk.
Pressthisbuttonfor
about 2 seconds to attract attention:
the horn will sound, and the exterior
lights will f lash f or about 30 seconds.
To cancel panic mode, press any
other button on the remote
transmitter, or turn the ignition
switch to the ON (II) position.
81
UNL OCK
LOCK TRUNK
PA NIC
Remote Transmitter
Inst rument s and Cont rols
99
LOCK
BUTTON
UNLOCK
BUTTON
PANIC
BUTTON
TRUNK
BUTTON
\f—\f—
y
\f
y
(%\fy\f
\fy
2008 TL

µ
See pages f or important saf ety
inf ormation and warnings about how toproperly position seats and seat-backs. 1213
The controls f or the power
adjustable front seats are on the
outside edge of each seat bottom.
You can adjust the seats with the
ignition switch in any position. Make
all seat adjustments bef ore you start
driving.
Moving the long horizontal switch on
the driver’s seat adjusts the seat
bottom in several directions. On the
passenger’s seat, the long horizontal
switch moves the seat only back and
f orth. The short vertical switch
adjusts the seat back angle.
The short horizontal switch on the
driver’s seat adjusts the degree of
lumbar support. Moves the seat forward
and backward.
Adjusts the seat-back
angle f orward or
backward.
Increases or decreases
the lumbar support.
(Driver’s seat only)
Moves the f ront of the
seat up or down. (Driver’s
seat only)
Moves the whole seat up
and f orward, or down
and backward. The front
of the seat also tilts up or
down at the same time.
(Driver’s seat only)
Raises or lowers the seat.
(Driver’s seat only)
Front Seat Power A djustments
Seats
Inst rument s and Cont rols
103
PASSENGER’S SEAT
DRIVER’S SEAT
\f—\f—
y
\fy
(%\fy\f
\fy
2008 TL

The outside mirrors are heated to
remove fog and frost. With the
ignition switch in the ON (II)
position, turn on the heaters by
pressing the button. The indicator in
the button comes on as a reminder.
Press the button again to turn the
heaters off.
With the ignition switch in the ON
(II) position, move the selector
switch to the L (driver’s side), or R
(passenger’s side).
Push the edge of the adjustment
switch to move the mirror right,
lef t, up, or down.
When f inished, move the selector
switch back to the center (off)
position. Both outside door mirrors have a
reverse tilt f eature. When in
reverse, the selected mirror will
tilt down slightly to improve your
view as you parallel park. Shifting
out of reverse will return the
mirrors to their original position.
To tilt the driver’s mirror, place
the selector switch in the left
position.
To tilt the passenger’s mirror,
place the switch in the right
position.
To turn the feature off, place the
switch in the center position.
Outside mirror positions can be
stored in the driving position
memory system (see page ).
3.
1.
2.
108
Power Mirror Heaters
Adjusting the Power Mirrors
Mirrors
Reverse Tilt Door Mirror
Inst rument s and Cont rols
107
HEATED MIRROR BUTTON
SELECTOR SWITCH
ADJUSTMENT
SWITCH
\f—\f—
y
\fy
(%\fy\f

y
2008 TL

Two seat and outside mirror
positionscanbestoredinseparate
memories. You select a memorized
position by pushing the appropriate
button or using the appropriate
remote transmitter (Driver 1 or
Driver 2).Adjust the outside mirrors f or best
visibility (see page ).
Adjust the seat to a comfortable
position (see page ).
Turn the ignition switch to the ON
(II) position. You cannot add a
new driving position to the
memory unless the ignition switch
is in the ON (II) position. You can
recall a memorized position with
the ignition switch in any position.
Store a driving position only when
the vehicle is parked.
Your vehicle has a memory feature
f or the driver’s seat and outside
mirror positions.
Press and release the MEMO
button on the driver’s door. You
will hear a beep. Immediately
press and hold one of the memory
buttons (1 or 2) until you hear two
beeps. The indicator in the
memory button will come on. The
current positions of the driver’s
seat and outside mirrors are now
stored.
3.
1.
2.
107
103
Storing a Driving Position in
Memory
Driving Position Memory System
108
MEMO BUTTON
MEMORY BUTTONS
\f—\f—
y
\fy
(%\fy\f

y
2008 TL

Follow these precautions whenever
you use the seat heaters:Use the HI setting only to heat the
seats quickly, because it draws
large amounts of current f rom the
battery.
If the engine is lef t idling f or an
extended period, do not use the
seat heaters even on the LO
setting. It can weaken the battery,
causing hard starting.
Both f ront seats are equipped with
seat heaters. Because of the sensors
f or the side airbag cutof f system,
there is no heater in the passenger’s
seat-back. The ignition switch must
be in the ON (II) position to use the
heaters. Push the right side of the switch, HI,
to rapidly heat up the seat. Af ter the
seat reaches a comfortable
temperature, select LO by pushing
the lef t side of the switch. This will
keep the seat warm.
In the LO setting, the heater runs
continuously. It does not cycle with
temperature changes.
In the HI setting, the heater turns off
when the seat gets warm, and turns
back on after the seat’s temperature
drops.
Seat Heaters
Inst rument s and Cont rols
111
SEAT HEATER SWITCHES
\f—\f—
y
\fy
(%\fy\f

y
2008 TL

µ
Turn the ignition switch to the ON
(II) position to raise or lower any
window. To open a window, push the
switchdownandholdit.Releasethe
switch when you want the window to
stop. Pull back on the switch and
hold it to close the window. The windows will operate f or up to
10 minutes af ter you turn of f the
ignition switch. Opening either f ront
door cancels this f unction.
The driver’s door armrest has a
master power window control panel.
To open the passenger’s window,
push down on the appropriate switch
and hold it until the window reaches
the desired position. To close the
window, pull back on the window
switch. Release the switch when the
window gets to the position you want.
To open either f ront
window f ully, push the window
switch f irmly down to the second
detent, then release it. The window
automatically goes down all the way.
To stop the window f rom going all
the way down, pull back on the
window switch briefly.
AUTO
Power Windows
112
DRIVER’S WINDOW
SWITCH MAIN
SWITCH
Closing a power window on
someone’s hands or fingers can
cause serious injury.
Make sure your passengers are
away from the windows before
closing them.
\f—\f—
y
\f\fy
(%\fy\f

y
2008 TL