2008 Acura MDX change wheel

ÛÝÛÝ
ÛÝThe multi-inf ormation display in the
instrument panel displays various
inf ormation and messages when the
ignition switch is in the ON (II)
position. Some of the messages help
you operate your vehicle more
comf ortably.
Others help to keep you aware of the
periodic maintenance your vehicle
needs f or continued trouble-f ree
driving.
When you open the driver’s door, a
‘‘Welcome’’ message is shown on the
multi-inf ormation display. When you
turn the ignition switch from the ON
(II) position to the ACCESSORY (I)
position, a ‘‘Goodbye’’ message is
shownonthedisplay.
To change the display, press the
INFO( / )buttononthesteering
wheel repeatedly until the main
menu appears (see page ).With the ignition switch in the ON
(II) position, the multi-inf ormation
display changes as shown in the next
page each time you press the INFO
( / ) button or SEL/RESET
button.
When you turn the ignition switch to
the ON (II) position, what you last
selected is displayed.
In the multi-information display, the
system message is also displayed
(see page ) and you can
customize your vehicle control
settings (see page ).
74 83
80
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
73
INFO ( / )
BUTTON
SEL/
RESET
BUTTON
\f—\f—\fy\f

y
()-
\fy\f\fy
2008 MDX

Whenthetirepressuremonitoris
shown on the multi-inf ormation
display, press the SEL/RESET
button. The display changes as
shown.
You can see the pressure of each tire
in this monitor. If one or more tires
are low, inflate them to the correct
pressure. For more inf ormation, see
page .
This monitor shows how much
torque is being delivered to each
wheel. For more inf ormation, see
page .
This shows the remaining lif e of the
engine oil. It shows 100% af ter the
engine oil is replaced and the display
is reset. The engine oil lif e is
calculated based on engine operating
conditions and accumulated engine
revolutions. For more inf ormation,
see page .
383 348
351
Tire Pressure Monitor
Monitor
Engine Oil L if e
Multi-Inf ormation Display
Inst rument s and Cont rols
77
U.S.
Canada
ENGINE OIL LIFE
\f—\f—\fy\f
y
()-
\fy\f\fy
SH-AWD®T orque Distribution
2008 MDX

ÎÎÎ
Î Î
Î
Î
Î
Î
µ™¶ ™
µ™¶ ™
Î TRIP B
LOW
MIN
OFF
ENGLISH
FRENCH
SPANISH
5°F 0°F 5°F
(U.S.) 3°C 0°C 3°C
(Canada)
ON
OFF
HIGH
MID
LOW
MANUAL ONLY
IGN OFF
TRIP A
MAX
HIGH
MID
ON
OFF
ON
OFF
MET ER SET UP
(P.89)
POSITION SETUP
(P.97)
90
91
92
93
94
95
98
99
LANGUAGE SELECT ION
ADJUST OUTSIDE
TEMP. DISPLAY
TRIP A & AVG. FUEL
RESET with REFUEL
ADJUST
ALARM VOLUME
ELAPSED TIME RESET
AUTO INTERIOR
ILLUMINATION
MEMORY POSIT ION LINK
AUTO TILT & TELESCOPE
STEERING WHEEL Changes the language used in the display.
Changes the outside temperature reading above or
below its current reading.
Causes trip meter A and the average fuel economy
to reset when you refuel.
Changes the indicator alarm volumes into three
levels.
Resets the elapsed time of your current trip.
Changes the interior light sensitivity to your liking.
Changes the driver’s seat, the steering wheel, and
the outside mirror positions to a stored setting.
Moves the steering wheel fully in and up when the
key is removed.
: Default setting
Setting Option
Group Setup Page
Menu Item Description
Multi-Inf ormation Display
84
——yy
()-
yy
2008 MDX

Û
Ý
ÛÝ
ÛÝ
CONT INUED
Here are the two custom settings for
the position setup:MEMORY POSITION LINK
AUTO TILT & TELESCOPE
STEERING WHEEL
While ‘‘POSITION SETUP’’ is shown,
press the SEL/RESET button to
enter the customize mode.
Each time you press the INFO ( / ) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection.
Multi-Inf ormation Display
Position Setup
Inst rument s and Cont rols
97
SEL/RESET
BUTTON
INFO ( or )
BUTTON
\f—\f—\fy\fy
()-
\fy\f
\fy
2008 MDX

ÛÝÛÝ
Memory Position Link
If ‘‘MEMORY POSITION LINK’’ is
set to ‘‘ON,’’ the driver’s seat, the
steering wheel, and outside mirror
positions move to the position stored
in the memory when you open the
driver’s door, using the remote
transmitter.
You can choose this customize item
f rom ‘‘POSITION SETUP’’ by
pressing the INFO ( / ) button
repeatedly. Press the SEL/RESET button to see
the selections.
Select ON or OFF by pressing the
INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button.
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘MEMORY POSITION LINK’’ and
repeat the procedure again.
Multi-Inf ormation Display
98
\f—\f—\fy\fy
()-
\fy\f
\fy
2008 MDX

ÛÝÛÝ
CONT INUED
Auto Tilt & Telescope Steering Wheel
When ‘‘AUTO TILT & TELESCOPE
STEERING WHEEL’’ is set to ‘‘ON,’’
the steering wheel automatically
moves f ully in and up when you turn
the ignition switch to the LOCK (0)
position and remove the key.
You can choose this customize item
f rom ‘‘POSITION SETUP’’ by
pressing the INFO ( / ) button
repeatedly. Press the SEL/RESET button to see
the selections.
Select ON or OFF by pressing the
INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button.
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to ‘‘AUTO
TILT & TELESCOPE STEERING
WHEEL’’ and repeat the procedure
again.
Multi-Inf ormation Display
Inst rument s and Cont rols
99
\f—\f—\fy\fy
()-
\fy\f
\fy
2008 MDX

When you remove the key f rom the
ignition switch, the steering wheel
automatically moves f ully in and up.If your vehicle’s battery is
disconnected or goes dead, or the
f use f or the power tilt and telescopic
steering wheel is removed, the
power tilt and telescopic steering
wheel system needs to be reset
when you reconnect the battery or
install the f use.
Insert the key into the ignition
switch, and remove it. The steering
wheel automatically moves f ully in
and up to let you know the system is
reset.
To change the ‘‘AUTO TILT &
TELESCOPE STEERING WHEEL’’
setting, see page .
The steering wheel then returns to
its original position when you insert
the key back in the ignition switch.
Steering wheel movement is also
controlled by the driving position
memory system (see page ).
99
157
Steering Wheel A djustments
Inst rument s and Cont rols
125
\f—\f—\fy\f
y
()-
\fy\f
\fy
2008 MDX

Doing any of the f ollowing af ter
pressing the MEMO button will
cancel the storing procedure.Not pressing a memory button
within 5 seconds.
Readjusting the seat position.
Readjusting the outside mirror
position.
Each memory button stores only one
driving position. Storing a new
position erases the previous setting
stored in that button’s memory. If
you want to add a new position while
retaining the current one, use the
other memory button. To select a memorized position, do
this:
To stop the system’s automatic
adjustment, do any of these actions:
Press any button on the control
panel: MEMO, 1, or 2.
Push any of the adjustment
switches f or the seat.
Shif t out of Park.
Adjust the outside mirrors.
Make sure the vehicle is parked.
Press the desired memory button
(1 or 2) until you hear a beep, then
release the button.
To change the ‘‘MEMORY
POSITION LINK’’ setting, see page . If desired, you can use the
adjustment switches to change the
positions of the seat, steering wheel
or outside mirrors af ter they are in
their memorized position. If you
change the memorized position, the
indicator in the memory button will
go out. To keep this driving position
f or later use, you must store it in the
driving position memory.
The system will move the seat,
steering wheel, and outside mirrors
to the memorized positions. The
indicator in the selected memory
button will f lash during movement.
When the adjustments are complete,
you will hear two beeps, and the
indicator will remain on.
1.
2.
98
Selecting a Memorized Position
Driving Position Memory System
158
\f—\f—\fy\fy
()-
\fy\f
y
2008 MDX