2008.5 Peugeot 1007 Dag child lock

3
62
"ISOFIX" MOUNTINGS
Your vehicle has been approved in
accordance with the new ISOFIX
regulation .
The seats * , represented below, are
fi tted with regulation ISOFIX mount-
ings: These are three rings for each seat: This ISOFIX mounting system
guarantees you fast, reliable and
safe fi tting of the child seat in your
vehicle.
The ISOFIX child seats are fi tted
with two locks which are secured
easily on these lower rings A .
Some also have an upper strap
which is attached to the upper ring B .
- two lower rings A , located be-
tween the vehicle seat back and
cushion, indicated by a label,
- an upper ring B , referred to as
the TOP TETHER , indicated by
a label. To attach this strap, raise the
vehicle seat's head restraint
then pass the hook between
its rods. Then fi x the hook on
the upper ring
B and tighten
the upper strap.
The incorrect installation of a
child seat in a vehicle compro-
mises the child's protection in
the event of an accident.
For information regarding the ISOFIX
child seats which can be installed in
your vehicle, consult the summary
table for the location of the ISOFIX
child seats.
Child seats fi tted with a support which
rests on the fl oor of the vehicle must
not be installed in the rear
* According to version.

4
78
ELECTRIC WINDOWS

1. Driver's electric window
switch.

2. Passenger electric window
switch. You can close all of the
windows using the remote
control when locking (refer
to the chapter "Access - §
Remote control key").
The electric window switches are not
active when the door concerned is
open.
The movement of a window stops if
the door is opened. A second action
on the electric window switch will
only be taken into account when the
door is closed.
Safety auto-reverse
In automatic mode, when the window
rises and meets an obstacle, it stops
and partially lowers again. In the case of unwanted
opening of the window on
closing or if the window will
not rise, lower it completely
and raise it again immediately, by
pulling the switch until the window
closes completely. Continue to press
the switch for approximately one
second after closing.

The safety auto-reverse function
is not operational during these
operations.
Electric window
Press or pull switch 1 . The
window stops as soon as the
switch is released.
One-touch electric window
with safety auto-reverse
You have two options: -
Manual mode:
Press or pull switch 1 gently.
The window stops as soon
as the switch is released.
- Automatic mode:
Press or pull switch 1 fully. The win-
dow opens or closes completely
when the switch is released.
Pressing the switch again stops the
movement of the window.

Note: the electrical functions of the
one-touch electric windows are de-
activated approximately one minute
after the ignition is switched off.

Note: the electrical functions of the
electric windows are deactivated
approximately 45 seconds after the
ignition is switched off, or when a
door is opened. Always remove the key from
the ignition when leaving
the vehicle, even for a short
time.
In the event of contact when operating
the windows, you must reverse the
movement of the window. To do this,
press the switch concerned.
When the driver operates the pas-
senger window switches, he must
ensure that no one is preventing cor-
rect closing of the window.
The driver must ensure that passengers
use the electric windows correctly.
Be aware of children when operating
the windows.

4
81
General
recommendations
Always check that it is safe to operate
the door and be sure, in particular, not
to leave children or animals near the
door controls without supervision.
When opening the door, with the win-
dow open, ensure that no person,
animal or object is hanging through
the window.
Before any opening or closing and
during any movement of the doors,
ensure that no person, animal or ob-
ject is preventing the required ma-
noeuvre, either inside or outside the
vehicle.
It is imperative that the doors are
operated only when the vehicle is
stationary.
For your safety and for that of your pas-
sengers, as well as for correct operation
of the doors, you are strongly advised
not to drive with a door open. The au-
dible warning, the lighting of the "door
open" warning light and the message
on the multifunction display are there to
remind you.
Lock your vehicle when using an au-
tomatic carwash. The doors and the overall
dimensions of the vehicle
Safety/Obstacle detection
The obstacle detection system is
triggered when an obstacle of a cer-
tain physical resistance hinders the
movement of the door.

4
84
PANORAMIC SUNROOF
This sunroof is a panoramic assembly
which provides maximum brightness
and visibility in the passenger com-
partment.
It consists of two parts:
- a fi xed rear part,
- a moving front part.
Each part has an independent manual
shutter.
The sunroof is controlled electrically
by a dial with 9 opening positions. Operation

To open: turn the dial to the left (nine
possible settings).
Once the roof is open, the front shutter
cannot be closed.

To close: return the control to the
initial position "O" . Reinitialisation
Following reconnection of the bat-
tery, in the event of a malfunction or
in the event of unwanted opening of
the roof on closing, the safety auto-
reverse must be reinitialised:
- place the dial in the fully closed
position (initial position "O" ),
- press the dial immediately,
- continue to press until the roof is fully closed.
Always remove the ignition
key when leaving the vehi-
cle, even for a short time.
In the event of contact during
operation of the roof, the movement
of the roof must be reversed. To do
this, operate the control concerned.
When the driver operates the roof
control, he must ensure that no one
is preventing the roof from closing
correctly.
The driver must ensure that the pas-
sengers use the sunroof correctly.
Be aware of children when operating
the roof.
Check that the slides are clean to en-
sure that the sunroof slides correctly.
Safety auto-reverse
When the roof meets an obstacle
while closing, it partially opens again.
You can close the sunroof
using the remote control
when locking (refer to the
corresponding chapter).

The safety auto-reverse function is
not operational during this operation.