2008.5 Citroen NEMO display

38
Steering wheel controls
Headlamp beam
You are advised to adjust the height of the
headlamp beams in accordance with the
load in your vehicle.
This function can only be accessed in
the main beam headlamps and dipped
headlamps position.
Press these controls, located
on the fascia panel, several
times in succession to adjust the
headlamps.
Fog lamps
The controls are located on the fascia panel
control pad.
Front and rear fog lamps
The fog lamps should only be used in
fog or when snow is falling.
In clear weather or in rain, both day and
night, lit rear fog lamps dazzle and are
prohibited.
Do not forget to switch them off when they
are no longer necessary.
"Guide me home" lighting
The temporary maintaining of the dipped
headlamps, after switching off the vehicle’s
ignition, makes the driver ’s exit easier when
the light is poor and lights the space in front
of the vehicle.
Activation
With the ignition key in the STOP position
or removed, pull the lighting control towards
the steering wheel within 2 minutes after
switching off the engine.
Each time the control is operated, the
duration for which the lights will remain on is
extended by 30 seconds, up to a maximum
of 210 seconds. Once this period of time has
elapsed, the lights switch off automatically.
Deactivation
Pull the lighting control towards the steering
wheel for more than 2 seconds.
The front fog lamps operate with
the side lights and the dipped
headlamps.
The rear fog lamps operate with
the dipped headlamps.
Press one of these controls to switch on the
lights.
The warning light comes on,
accompanied by a message
on the display, the first time
the control is operated and
remains on until the function is deactivated
automatically.
An indicator light on the display
indicates the adjustment position
selected (0, 1, 2, 3).

43
1
READY TO SET OFF
Gearbox and steering wheel
ELECTRONIC GEARBOX SYSTEM
The 5-speed electronic gearbox system
gives you the choice between the comfort of
automatic mode or the driving pleasure of a
manual gearbox.
This gearbox gives you access to two driving
modes:
- an automatic mode for the automatic
management of gear changes, with no
driver intervention necessary,
- a sequential mode for manual gear
changes made by the driver using the
gear lever.
It is comprised of a gear lever 1 on the
central console to select the driving mode,
reverse gear and neutral, or to select
sequential mode.
Gear lever positions
N: neutral.
With your foot on the brake pedal, select this
position to start the engine.
R: reverse gear.
With the vehicle stationary, hold your foot
down on the brake pedal and push the gear
lever upwards.
A: automatic mode.
Move the gear lever downwards to select
this mode.
M+/-: sequential mode with manual gear
changes.
Move the lever downwards, then to the left
to select this mode, then:
- push it forwards to move up a gear,
- pull it backwards to go down a gear.
Starting the vehicle
Select position N .
Press firmly on the brake pedal whilst
starting the engine.
Start the engine. "N" appears on the
instrument panel display.
Select first gear (position M or A) or reverse
gear (position R).
Release the parking brake.
Remove your foot from the brake pedal, then
accelerate.
"AUTO" and "1" or "R" appear on the
instrument panel display.
It is possible to start in second gear,
only in sequential mode.

44
Gearbox and steering wheel
Stopping - Starting on a gradient
This is an electronic gearbox system without
a clutch pedal.
To immobilise the vehicle on a gradient,
you must use the parking brake and not
the accelerator.
When starting on a gradient, accelerate
gradually while releasing the parking brake.
Changing to sequential mode
Once you have started the engine, you
can go into sequential mode by selecting
position M.
Changing to automatic mode
When in sequential mode, you can return to
automatic mode by selecting position A.
Stopping the vehicle
Before switching off the engine, you can:
- select position N to engage neutral.
- leave a gear engaged, such as first or
reverse gear.
In either case, you must engage the parking
brake to immobilise the vehicle.
Reinitialising
Following a battery disconnection, you must
reinitialise the gearbox:
- switch on the ignition, "AUTO" appears
on the instrument panel display,
- press on the brake pedal,
- wait for about 30 seconds until "N" or
a gear appears on the instrument panel
display,
- release the brake pedal.
The gearbox is now operational again.
Operating anomaly
"AUTO" is displayed and the
gear selected appears on the
instrument panel display.
The gearbox operates in
automatic mode, without the need for driver
intervention.
It always selects the gear best suited to the
following parameters:
- driving style,
- road profile,
- vehicle load.
To maximise driving comfort and obtain the
most suitable gear, avoid making rough
movements on the accelerator pedal.
If you press the accelerator beyond the point
of resistance, the gearbox selects the next
gear down to allow for faster acceleration.
"AUTO" disappears and
the gears selected appear
successively on the instrument
panel display.
Gear change requests are only possible if
the engine speed allows them.
Gently lift your foot from the accelerator
pedal to select the gear.
When driving at low speed (e.g. approaching
a stop sign or at traffic lights), the gearbox
automatically changes down to first gear.
With the ignition switched on, the
fl ashing of "AUTO" and the lighting
of this warning lamp, accompanied
by a sound signal and a message on
the instrument panel display, indicate a gearbox
malfunction.
Have the system checked by your CITROËN dealer.
You must always press the brake pedal down when starting the engine. When the vehicle is moving, never select neutral N.Only select reverse gear R with the vehicle stationary and your foot on the brake pedal.In all cases, you must engage the parking brake to immobilise the vehicle.When on a steep gradient, you are advised to use sequential mode.

1
READY TO SET OFF
Gearbox and steering wheel
Function selected,
"Cruise control" warning lamp displayed.
Function deactivated,
OFF (e.g. 107 km/h).
Function activated
(e.g. 107 km/h). Speed exceeded
(e.g. 118 km/h),
the programmed speed flashes.
CRUISE CONTROL "CRUISE"
This driving aid enables you to
maintain a constant programmed
speed when driving in free-flowing
traffic, except when on a steep
incline.
To programme or activate cruise control,
the vehicle’s speed must be over 25 mph
(40 km/h), with at least 4th gear engaged
(2nd gear for electronic gearbox system).
The status of the function and the
programmed speed is displayed on the
instrument panel: Operational fault detected,
OFF
- the dashes flash.

48
Gearbox and steering wheel
Function selected,
"Speed limiter" warning lamp displayed.
Function deactivated,
last programmed speed - OFF
(e.g. 107 km/h).Function activated
(e.g. 107 km/h).
Speed exceeded
(e.g. 118 km/h),
the programmed speed flashes.
Operational fault detected,
OFF - the dashes flash.
SPEED LIMITER "LIMIT"
This function can be selected either
while driving, or while stationary with
the engine running.
The minumum speed that you can
programme is 20 mph (approx. 30 km/h).
You can accelerate up to the programmed
speed, at which point the accelerator will
reach its point of resistance, indicating that
you have reached the programmed speed.
However, if you press the pedal down to the
floor past the point of resistance, you can
exceed the programmed speed. To return
to the programmed speed, you merely need
to gradually release the pressure on the
accelerator pedal and return to a speed
below the programmed speed. Adjustments can be made while driving,
or while stationary with the engine
running.
The status of the function and the
programmed speed is displayed on the
instrument panel:

49
1
READY TO SET OFF
Gearbox and steering wheel
Selecting the function
- Turn the ring to LIMIT position.
The speed limiter is selected but is not
yet activated. The last programmed
speed is displayed.
Programming a speed
You can programme the speed without
activating the speed limiter (with the engine
running).
To memorise a higher speed than that
already memorised:
- move the control up (+).
A short press increases the speed by 1 mph.
Holding it down increases the speed in steps
of 5 mph.
To memorise a lower speed than that
already memorised:
- move the control down (-).
A short press decreases the speed by
1 mph.
Holding it down decreases the speed in
steps of 5 mph.
Activation/deactivation (off)
A first press on this button activates the
speed limiter, a second press deactivates it
(OFF).

61
3
IN-CAR TECHNOLOGY
Trip computer
TRIP COMPUTER
The TRIP button, located at the end of
the wipers stalk, provides access to the
following information: - Range,
- Route A,
- Average consumption A,
- Current consumption A,
- Average speed A,
- Trip duration A. If TRIP B is activated on
MENU :
- Route B,
- Average consumption B,
- Average speed B,
- Trip duration B.
Press the MENU ESC button for over
2 seconds to return to the main screen.
Zero reset
Press the TRIP for over 2 seconds to reset
the displayed values to zero.
Level 1 display:
- Speed (Speed bleep).
- Hour (Setting of the time).
- Buzz (Volume of the announcements).
- Unit (Unit of measurement).
- Bag p (Passenger air bag).

Refer to the corresponding line in the configuration-personalisation table on the following pages.

62
Menu
MENU Eight languages are offered: Italian, English,
German, French, Spanish, Portuguese,
Dutch and Turkish.
As a safety precaution, the menus can
only be accessed when the ignition is off
(engine off).
Refer to the corresponding line in the
configuration-personalisation table on the
following pages.
This button enables you to:
- scroll up through a menu,
- increase a value.

This button enables you to:
- scroll down through a menu,
- decrease a value.

Menu... Press...
Sub-
menu...
Press... Select...
Confirm
and exit
Enables you to...

1 Speed Bleep ON Increase
Activate/deactivate the audible
signal indicating exceeding of the
programmed speed and select the
speed value.
Decrease
OFF

2 Activate
Trip B ON Activate
Display a second route "Trip B".
OFF
Deactivate
Confi guration-Personalisation

Level 2 and 3 displays:
The control panel located to the left of
the steering wheel provides access to
the display menus, which allow you to
personalise some of your equipment.
This button enables
you to:
- access the menus and sub-menus,
- confirm your selections within a menu,
- exit from the menus.
A long press enables you to return to the
welcome screen.