2008.5 Citroen C5 ignition
[x] Cancel search: ignitionPage 158 of 306
158
10
C H E C K S
Screenwash and headlamp
wash fluid
F l u i d s p e c i fi c a t i o n
For optimum cleaning and to avoid free-
z i n g , t h i s fl u i d m u s t n o t b e t o p p e d u p o r
replaced with water.
Reservoir capacities:
- s c r e e n w a s h : a p p r o x i m a t e l y 3 . 5 l i t r e s ,
- screenwash and headlamp wash: a p p r o x i m a t e l y 6 . 1 5 l i t r e s .
Diesel additive level (Diesel
engine with particle emission
filter)
A low additive level is indicated by
lighting of the service warning lamp,
accompanied by an audible warning
and a message on the multifunction
screen.
Topping up
This additive must be topped up by
a CITROËN dealer without delay.
Used products
Avoid prolonged contact of
u s e d o i l o r fl u i d s w i t h t h e
skin.
M o s t o f t h e s e fl u i d s a r e h a r m f u l t o
health or indeed very corrosive.
Do not discard used oil or
fl u i d s i n t o s e w e r s o r o n t o
the ground.
Take used oil to a an authorised
waste disposal site CITROËN.
I n t h e c a s e o f v e h i c l e s fi t t e d
with headlamp washers, the
m i n i m u m l e v e l o f t h i s fl u i d i s
indicated by an audible signal
and a message on the multifunction
screen.
Top up the level when you stop the
vehicle.
Coolant level
Coolant change
The coolant does not have to be
changed.
F l u i d s p e c i fi c a t i o n
The coolant must conform to the
manufacturer’s recommendations. The coolant level should be
close to the "MAX" mark but
s h o u l d n e v e r e x c e e d i t .
When the engine is warm, the tem-
perature of the coolant is regulated
by the fan. This can operate with the
ignition off.
O n v e h i c l e s w h i c h a r e fi t t e d w i t h
a p a r t i c l e e m i s s i o n fi l t e r , t h e f a n
may operate after the vehicle has
been switched off, even if the en-
gine is cold.
In addition, as the cooling system is
pressurised, wait at least one hour
after switching off the engine before
carrying out any work.
To avoid any risk of scalding, unscrew
the cap by two turns to allow the pres-
sure to drop. When the pressure has
dropped, remove the cap and top up
the level.
Page 161 of 306
161
11
P R A C T I C A L I N F O R M A T I O N
PUNCTURE REPAIR KIT Using the kit
The puncture repair kit is located in
t h e b o o t u n d e r t h e fl o o r .
Switch off the ignition.
A f fi x t h e s p e e d l i m i t a t i o n s t i c k e r
to the vehicle’s steering wheel
to remind you that a wheel is in
temporary use.
Check that the switch A is in po-
sition "0" .
Connect the pipe of the bottle 1
to the valve of the tyre to be re-
paired.
Connect the compressor’s elec-
tric plug to the vehicle’s 12 V
socket.
Start the vehicle and leave the
engine running.
Complete system consisting of a
compressor and a bottle of sealant
product which permits
temporary
repair of the tyre so that you can
drive to the nearest garage.
This repair kit is available from
CITROËN dealers.
It is designed to repair holes of a
m a x i m u m d i a m e t e r o f 6 m m , l o c a t -
e d e x c l u s i v e l y o n t h e t y r e t r e a d o r
shoulder. Avoid removing any for-
eign bodies which have penetrated
the tyre.
Page 166 of 306
166
P R A C T I C A L I N F O R M A T I O N
Removing a wheel
P a r k t h e v e h i c l e o n s t a b l e , fi r m
ground that is not slippery. apply
the parking brake.
If your vehicle is equipped with
"Hydractive III+" suspension,
with the engine running at idle,
adjust the ground clearance to
i t s m a x i m u m h e i g h t .
Switch off the ignition and en-
g a g e fi r s t g e a r o r r e v e r s e g e a r
depending on any slope (for a
v e h i c l e w i t h a u t o m a t i c g e a r b o x ,
select position P).
I f y o u r v e h i c l e i s fi t t e d w i t h
"Hydractive III+" suspension,
position the chock, whichever di-
rection the gradient may be in, in
front of the front wheel diametri-
cally opposite to the one to be
replaced.
Position the jack at one of the
four jacking-points provided
on the underbody close to the
wheels, then use the wheelbrace
to unwind the jack until it reaches
the ground.
Remove the protector from each
bolt using tool 3 .
Slacken the wheel bolts.
Before positioning the
jack:
Always adjust the vehicle’s
g r o u n d c l e a r a n c e t o t h e " m a x i -
mum height" position and re-
tain this adjustment for as long
as the jack is under the vehi-
cle (do not use the hydraulic
adjustments),
Immobilise your vehicle on hori-
zontal, stable and non-slippery
ground,
Ensure that any passengers
have left the vehicle and are in
a safe place .
Never get underneath the vehicle if
it is supported only by the jack.
The jack and all of the tools are
s p e c i fi c t o y o u r v e h i c l e . D o n o t u s e
them for any other applications.
Have the original wheel repaired
a n d r e fi t t e d a s s o o n a s p o s s i b l e .
C o n t i n u e t o e x t e n d t h e j a c k u n t i l
the wheel is a few centimetres
off the ground.
Undo the bolts, remove the
wheel.
Page 183 of 306
180
11
P R A C T I C A L I N F O R M A T I O N
FUSEBOX C
Fuse N° Rating
Function
F1 15 A Rear screen wipe (Tourer)
F2 30 A Locking and deadlocking relay
F3 5 A Airbags
F4 10 A A u t o m a t i c g e a r b o x - a d d i t i o n a l h e a t e r u n i t ( D i e s e l ) - e l e c t r o c h r o m e r e a r v i e w m i r r o r s
F5 30 A Front window - sun roof - passenger door lighting - passeng er rear view mirror adjustment
F6 30 A Rear window
F7 5 A V a n i t y m i r r o r l i g h t i n g - G l o v e b o x l i g h t i n g - i n t e r i o r l a m p s - t o r c h ( t o u r e r )
F8 20 A R a d i o - C D c h a n g e r - C o n t r o l s a t t h e s t e e r i n g w h e e l - D i s p l a
y - D e fl a t i o n d e t e c t i o n - E l e c t r i c
boot ECU
F9 30 A Cigar-lighter - front 12 V socket
F10 15 A Alarm - Controls on the steering wheel, signalling and scre en wipe controls
F11 15 A Low current ignition switch
F12 15 A Driver’s electric seat - instrument panel - seat belt not fasten
ed warning lamps -air
conditioning controls
F13 5 A Engine relay unit - Hydraulic suspension pump cut-off relay - a irbag ECU supply
F14 15 A Rain and brightness sensor - parking assistance - passenger’s electri
c seat - trailer relay
u n i t - H I F I a m p l i fi e r E C U - H a n d s - f r e e k i t - L a n e D e p a r t u r e W a r n i n g S y s t e m
F15 30 A Locking and deadlocking relay
F17 40 A H e a t e d r e a r s c r e e n - e x t e r i o r h e a t e d r e a r v i e w m i r r o r s
FSH SHUNT PARK SHUNT
Page 184 of 306
181
11
P R A C T I C A L I N F O R M A T I O N
Fuses under the bonnet
After a repair,
c a r e f u l l y r e fi t
the
cover.
Any repairs on the MAXI fuses
(that give additional protection),
located in the fuseboxes, must
be left to a CITROËN dealer.
Access to the fuses
Undo each screw by a 1/4 turn. Table of fuses
Fuse N° Rating Function
F1 20 A Engine control unit
F2 15 A Horn
F3 10 A Screen wash pump
F4 10 A Headlamp wash pump
F5 15 A Starter
F6 10 A A i r fl o w m e t e r - D i r e c t i o n a l h e a d l a m p s -
Diagnostic socket
F7 10 A Automatic selector lever lock - Power steering
F8 25 A Starter
F9 10 A Clutch switch - STOP switch
F10 30 A Starter
F11 40 A Air conditioning blower
F12 30 A Wipers
F13 40 A BSI supply (ignition on)
F14 30 A -
F15 10 A Right-hand main beam
F16 10 A Left-hand main beam
F17 15 A Right-hand dipped beam
F18 15 A Left-hand dipped beam
F19 15 A Starter
F20 10 A Starter
F21 5 A Starter
Page 187 of 306
184
P R A C T I C A L I N F O R M A T I O N
Charging the battery using a
battery charger
Disconnect the battery from the
vehicle.
Follow the instructions for use
provided by the manufacturer of
the charger.
Reconnect starting with the neg-
ative terminal (-).
Check that the terminals and
connectors are clean. If they are
covered with sulphate (whitish or
greenish deposit), remove them
and clean them.
The batteries contain harm-
ful substances such as sul-
phuric acid and lead. They
must be disposed of in accordance
with regulations and must not, in
any circumstances, be discarded
with household waste.
Take used remote control batteries
and vehicle batteries to a special
collection point.
It is advisable to disconnect the
battery if the vehicle is to be left un-
used for more than one month. Do not disconnect the ter-
minals while the engine is
running.
Do not charge the batteries without
d i s c o n n e c t i n g t h e t e r m i n a l s fi r s t .
Do not touch the clips during the
operation.
Do not lean over the batteries.
Disconnect the cables in the re-
verse order to connection, ensur-
ing that they do not touch.
Before disconnecting the
battery
Wait 2 minutes after switching off
the ignition before disconnecting
the battery.
Close the windows and the doors
before disconnecting the battery. Following reconnection of the
battery
Following reconnection of the bat-
tery, switch on the ignition and wait
1 minute before starting to permit
initialisation of the electronic sys-
tems. However, if slight malfunctions
remain following this operation, con-
tact a CITROËN dealer.
Referring to the corresponding sec-
tion, you must yourself reinitialise:
- the remote control key,
- the glass panoramic roof blind,
- the GPS satellite navigation
system.
Page 217 of 306
214
11
11
22
33
44
22
11
HANDS-FREE KIT
For safety reasons and because they require prolonged attention on the part of the driver, the operations for pairing the Bluetooth mobile telephone with your Audio System’s hands-free kit m ust be carried out with the vehicle stationary. The ignition must be on.
Select the accessory which corresponds to the n a m e o f t h e v e h i c l e , a s u p e r i m p o s e d c o n fi g u r a t i o n display appears on the multifunction screen.
Activate the telephone’s Bluetooth function and carry out a search of the Bluetooth accessories present for the telephone.
Select the YES tab on the display using t h e b u t t o n s t h e n c o n fi r m b y p r e s s i n g O K .
Enter the vehicle’s authentication code (=1234). Depending on the telephone, you may be asked to enter this code before the superimposed c o n fi g u r a t i o n d i s p l a y a p p e a r s .
YES
YES
The services offered by the hands-free kit depend on the network, the SIM card and the compatibility of the Bluetooth equipment used. C o n s u l t y o u r t e l e p h o n e ’ s m a n u a l a n d y o u r o p e r a t o r t o fi n d o u t w h i c h s e r v i c e s a r e a v a i l a b l e t o y o u . A list of mobile telephones which offer the best range of services is available from the network. Consult a CITROËN dealer.
RECEIVING A CALL
An incoming call is announced by a ring and a supe rimposed display on the multifunction display.
Select the YES tab on the display using t h e b u t t o n s a n d c o n fi r m b y p r e s s i n g O K .
Press the steering wheel control TEL to accept the call.
Press the steering wheel control TEL to access your directory.
To dial a number, use the keypad on your telephone.
MAKING A CALL
PAIRING A TELEPHONE
Page 245 of 306
23
07
1
3
5
4
2
1
The services available via the telephone depend on the network, the SIM card and the compatibility of the Bluetooth equipment used. Refer to your telephone's manual and your operator to check which services you have access to. A list of mobile telephones which offer the best range of services is available from dealers.
MAKING A TELEPHONE CALL
CONNECTING A BLUETOOTH
TELEPHONE
For safety reasons and because they require prolon gedonged attention on the part of the driver, the operations for pairing the Blue Bluetooth mobile telephone to the hands-free system of the NaviDrive 3Dive 3D must be carried out with the vehicle stationary and the ignition onition on.
Activate the telephone's Bluetooth function. The last telephone connected is reconnected automatically.
If no telephone is connected, the system prompts you to CONNECT PHONE. Select YES and press OK t o c o n fi r m .
Enter the authentication code on the telephone. The code to be entered is displayed on the screen.
To change the telephone connected, press the TEL button, then select TELEPHONE MENU, then SELECT PHONE then CONNECT BLUETOOTH TELEPHONE then select the telephone required or SEARCH PHONE. P r e s s O K a t e a c h s t e p t o c o n fi r m .
Once the telephone has been connected, the NaviDri veiDrive 3D can synchronise the address book and the call list. This syncis synchronisation may take a few minutes.
The list of telephones connected previously (4 max imumximum) appears on the multifunction display. Select the telephone required uired then select CONNECT PHONE for a new connection. Select DELE DELETE PHONE to cancel the connection to the telephone.
Press the TEL button.
F o r a fi r s t c o n n e c t i o n , s e l e c t SEARCH PHONE and press OK to c o n fi r m . T h e n s e l e c t t h e n a m e o f t h e telephone.
SEARCH PHONE