Page 148 of 306
147
9
D R I V I N G
Vehicle positions
Maximum height
Changing a wheel (Not possible if
speed > 6 mph (10 km/h)).
Intermediate position
For an increased ground clearance
(Not possible if speed > 25 mph
(40 km/h)).
F o r u s e o n d i f fi c u l t r o a d s w h e n t r a v -
elling at reduced speed, as well as
on car park ramps.
Position changes may only be
made when the engine is running.
Adjustable ground clearance re-
sponds to all types of situation.
A p a r t f r o m a f e w s p e c i fi c s i t u a t i o n s ,
driving in the normal road position is
imperative.
Press once on one of the adjust-
ment controls.
The change in position is indicated
by a message on the instrument
panel screen.
Normal position
If the speed authorised for a particu-
l a r p o s i t i o n i s e x c e e d e d , t h e v e h i c l e
reverts automatically to the normal
position.
Minimum height
To facilitate loading or unloading the
vehicle.
For workshop inspections.
Not to be used in normal driving (Not
possible if speed > 6 mph (10 km/h)).
Page 150 of 306
150
10
C H E C K S
BONNET
Protects the components of the
engine and provides access for
checking levels.
Opening
Lift the lever B and raise the bonnet.
Unclip the strut C from its housing
and pivot it to insert it in the notch
D indicated by a yellow arrow.
F i x t h e s t r u t i n t h e n o t c h t o h o l d
the bonnet open. Closing
Take the strut out of the support
notch.
Clip the strut in its housing.
Lower the bonnet then slam it
fi r m l y a t t h e e n d o f i t s t r a v e l .
Pull on the bonnet to check that
it is secured correctly.
To avoid any risk of burns, only han-
dle the bonnet strut by its yellow
end.
The location of the interior control
prevents opening of the bonnet
while the front passenger’s door is
closed.
This operation must only be carried
out when the vehicle is stationary.
Avoid opening the bonnet in strong
winds.
Open the front passenger door.
Pull the interior control A , located
at the bottom of the door frame.
Page 151 of 306
151
10
C H E C K S
DRAINING THE DIESEL FUEL FILTER
Protective cover
Removal of the cover Draining water from the fuel
filter
Drain regularly (at each oil change).
To drain the water, slacken the bleed
screw or the water in diesel fuel sen-
s o r , l o c a t e d a t t h e b a s e o f t h e fi l t e r .
Continue until all the water has
fl o w e d o u t .
Then retighten the bleed screw or
the water detection sensor.
HDi 110, HDi 173 and V6 HDi 208
engines
Pull the protective cover upwards
to remove it.
HDi 138 engine
Remove the protective cover
b y fi r s t u n c l i p p i n g a t 3 , then 1
and 4.
Unclip at 2 by pulling towards
you, then lift up. R e fi t t i n g
Firstly clip in at 2 .
Lower and centre the cover.
Clip in at 3 and 4 , pushing verti-
cally and gently from the rear.
Clip in at 1 pushing vertically.
Page 152 of 306
152
10
C H E C K S
RUNNING OUT OF FUEL (DIESEL)
HDi 110 engine
Unclip the protective cover
to gain access to the priming
pump. HDi 138 and HDi 173 engines
Unclip the protective cover
to gain access to the priming
pump.
Priming the fuel circuit
In the event of running out of fuel:
a f t e r fi l l i n g ( m i n i m u m 5 l i t r e s )
and removing the protective
cover, operate the manual prim-
ing pump, until some resistance
is felt,
operate the starter motor while
depressing the accelerator pedal
slightly until the engine starts. HDi engines are the result
of advanced technology.
All maintenance and repairs require
s p e c i a l q u a l i fi c a t i o n s w h i c h o n l y a
CITROËN dealer can guarantee.
V6 HDi 208 engine with electric
pump
In the event of running out of fuel:
after adding fuel, turn the ignition
key to position M , wait for a few
seconds,
operate the starter motor until
the engine starts.
If the engine fails to start after sev-
eral attempts, contact a CITROËN
dealer.
I f t h e e n g i n e f a i l s t o s t a r t a t t h e fi r s t
a t t e m p t , w a i t fi f t e e n s e c o n d s b e f o r e
trying again.
If the engine fails to start after a
few attempts, operate the priming
pump again and then try to start the
engine.
When the engine is idling, acceler-
ate slightly to complete the bleeding
of the circuit.
Page 153 of 306
153
10
C H E C K S
PETROL ENGINES
They allow you access for checking
t h e l e v e l o f t h e v a r i o u s fl u i d s a n d f o r
replacing certain components.
1. Screenwash and headlamp
wash reservoir.
2. P o w e r s t e e r i n g fl u i d r e s e r v o i r o r
power steering and suspension
fl u i d r e s e r v o i r .
3. Engine coolant reservoir.
4. Engine oil dipstick.
5. E n g i n e o i l fi l l e r c a p .
6. B r a k e fl u i d r e s e r v o i r .
7. Battery.
8. A i r fi l t e r .
V e h i c l e s fi t t e d w i t h t h e
2.0i 16V engine may be
fi t t e d w i t h m e t a l s u s p e n -
sion. In this case, a different power
s t e e r i n g fl u i d r e s e r v o i r i s fi t t e d .
1.8i 16V
2.0i 16V
Page 154 of 306
154
10
C H E C K S 3 litre V6 petrol engine
1. Screen wash and headlamp
wash reservoir.
2. Power steering and suspension
fl u i d r e s e r v o i r .
3. Engine coolant reservoir.
4. E n g i n e o i l fi l l e r c a p .
5. Engine oil topping-up.
6. B r a k e fl u i d r e s e r v o i r .
7. Battery.
8. A i r fi l t e r .
3.0i V6
Page 155 of 306
155
10
C H E C K S
DIESEL ENGINES
They allow you access for checking
t h e l e v e l o f t h e v a r i o u s fl u i d s , f o r r e -
placing certain components and for
repriming the fuel.
1. Screenwash and headlamp
wash reservoir.
2. P o w e r s t e e r i n g fl u i d r e s e r v o i r o r
power steering and suspension
fl u i d r e s e r v o i r , d e p e n d i n g o n
equipment.
3. Engine coolant reservoir.
4. Engine oil dipstick.
5. E n g i n e o i l fi l l e r c a p .
6. A i r fi l t e r .
7. B r a k e fl u i d r e s e r v o i r .
8. Battery.
As the diesel circuit is pres-
surised, any work on this
circuit is prohibited.
V e h i c l e s fi t t e d w i t h t h e HDi 138
e n g i n e m a y b e fi t t e d w i t h m e t a l
suspension. In this case, a differ-
e n t p o w e r s t e e r i n g fl u i d r e s e r v o i r i s
fi t t e d .
HDi 110
HDi 138
Page 156 of 306
156
10
C H E C K S HDi 173 - V6 HDi 208 engines
(with particle filter)
1. Screen wash and headlamp
wash reservoir.
2. Power steering and suspension
fl u i d r e s e r v o i r .
3. Engine coolant reservoir.
4. Engine oil dipstick.
5. E n g i n e o i l fi l l e r c a p .
6. A i r fi l t e r .
7. B r a k e fl u i d r e s e r v o i r .
8. Battery.
9. "+" and "-" terminals for starting
with a slave battery.
The diesel fuel circuit being
under high pressure:
- Any intervention on the circuit is prohibited.
- HDi engines are the result of advanced technology.
Any intervention requires spe-
c i a l q u a l i fi c a t i o n s w h i c h o n l y a
CITROËN dealer can guarantee.
HDi 173
V6 HDi 208
