2008.5 Citroen C5 light
[x] Cancel search: lightPage 120 of 306
122
9
D R I V I N G
MANUAL PARKING BRAKE
Mechanical device for immobilising
the vehicle when stationary. This warning lamp comes
on if the parking brake is en-
gaged or not fully released.
If the parking brake is released,
the lighting of this warning lamp
along with the STOP warning lamp
i n d i c a t e s a n i n s u f fi c i e n t l e v e l o f
b r a k e fl u i d o r a m a l f u n c t i o n o f t h e
braking distribution.
It is essential to stop the vehicle.
Consult a CITROËN dealer.
Application
Pull the parking brake to immobi-
lise your vehicle.
To facilitate the action on the lever,
you are recommended to press the
brake pedal at the same time.
In all circumstances, as a
precautionary measure,
e n g a g e fi r s t g e a r .
On steep gradients, turn the steer-
ing wheel towards the pavement. Release
Press on the end of the lever
whilst pulling it then lower it fully.
Page 121 of 306
123
9
D R I V I N G
ELECTRICPARKINGBRAKE
The electric parking brake combines
2 operational modes:
- AUTOMATIC
Automatic application when the engine stops and automatic re-
lease on use of the accelerator
(automatic operation by default),
- MANUAL
Manual application/release of the parking brake is always pos-
sible by pulling control A while
pressing the brake pedal. Automatic operation
Application with the engine off
With the vehicle stationary, the parking
brake
is automatically applied when
the engine is switched off.
The application of the parking brake
i s c o n fi r m e d b y : Application with the engine running
With the engine running and the ve-
hicle stationary, in order to immobi-
lise the vehicle you need to manually
apply the parking brake by
pulling
on control A .
The application of the parking brake
i s c o n fi r m e d b y :
- the lighting of the warning
lamp on control A and on
the instrument panel,
Before leaving the vehicle,
check that warning lamp P
on the instrument panel is
permanently lit.
Never leave a child alone inside the
vehicle with the ignition on, as they
could release the parking brake.
- the display of a message "parking
brake applied" on the instrument
panel screen.
T h e n o i s e o f o p e r a t i o n w i l l c o n fi r m t o
you the application/ release of your
electric parking brake. - the lighting of warning
lamp P on control A and
on the instrument panel,
- the display of a message "parking brake applied" on the instrument
panel screen.
When the driver’s door is opened, a
beep is heard and a message dis-
played if the parking brake has not
been applied.
Before leaving the vehicle,
check that warning lamp P
on the instrument panel is
permanently lit.
Page 122 of 306
124
9
D R I V I N G
Release
The electric parking brake releases
automatically and progressively
when you press the accelerator:
with a manual gearbox
( fi r s t gear or reverse gear engaged) ,
press down fully on the clutch
pedal then press on the accelera-
tor pedal and move off.
with an automatic gearbox , ac-
celerate with the selector in posi-
tion D , M or R .
Full release of the parking brake is
c o n fi r m e d b y : - the warning lamp P on
control A and on the in-
strument panel going out,
- the display of a message "parking brake released" on the instrument
panel screen.
When stationary, with the engine
running, do not press the accelerator
pedal unnecessarily (particularly
when starting the engine, including
in neutral), as you may release the
parking brake. Activation/Deactivation of the
automatic functions
The automatic application when the en-
gine is switched off and the automatic re-
lease when you press the accelerator can
be deactivated. Activation/deactivation is
p e r f o r m e d u s i n g t h e c o n fi g u r a t i o n m e n u
of the instrument panel screen. To do so,
s e l e c t " P e r s o n a l i s a t i o n / C o n fi g u r a t i o n /
D e fi n e t h e V e h i c l e p a r a m e t e r s / D r i v i n g
assistance/Automatic handbrake".
The deactivation of these
f u n c t i o n s i s c o n fi r m e d b y t h e
lighting of this warning lamp
on the instrument panel.
With the automatic functions deac-
tivated, the application and release
of the parking brake are done manu-
ally.
The deactivation of the auto-
matic functions is recommend-
ed in particularly cold conditions
(ice) and during towing (break-
down, caravan...).
Manual operation
Manual application/release of the
parking brake is always possible.
Application
With the vehicle stationary, to apply the
parking brake whether the engine is
running or off, pull on control A .
The application of the parking brake
i s c o n fi r m e d b y : - the lighting of the warning lamp on control A and of
warning lamp P on the in-
strument panel,
- the display of a message "parking brake applied" on the instrument
panel screen.
When the driver’s door is
opened with the engine run-
ning, a beep is heard and
a message displayed if the parking
brake has not been applied.
Page 123 of 306
124
9
D R I V I N G
Release
The electric parking brake releases
automatically and progressively
when you press the accelerator:
with a manual gearbox
( fi r s t gear or reverse gear engaged) ,
press down fully on the clutch
pedal then press on the accelera-
tor pedal and move off.
with an automatic gearbox , ac-
celerate with the selector in posi-
tion D , M or R .
Full release of the parking brake is
c o n fi r m e d b y : - the warning lamp P on
control A and on the in-
strument panel going out,
- the display of a message "parking brake released" on the instrument
panel screen.
When stationary, with the engine
running, do not press the accelerator
pedal unnecessarily (particularly
when starting the engine, including
in neutral), as you may release the
parking brake. Activation/Deactivation of the
automatic functions
The automatic application when the en-
gine is switched off and the automatic re-
lease when you press the accelerator can
be deactivated. Activation/deactivation is
p e r f o r m e d u s i n g t h e c o n fi g u r a t i o n m e n u
of the instrument panel screen. To do so,
s e l e c t " P e r s o n a l i s a t i o n / C o n fi g u r a t i o n /
D e fi n e t h e V e h i c l e p a r a m e t e r s / D r i v i n g
assistance/Automatic handbrake".
The deactivation of these
f u n c t i o n s i s c o n fi r m e d b y t h e
lighting of this warning lamp
on the instrument panel.
With the automatic functions deac-
tivated, the application and release
of the parking brake are done manu-
ally.
The deactivation of the auto-
matic functions is recommend-
ed in particularly cold conditions
(ice) and during towing (break-
down, caravan...).
Manual operation
Manual application/release of the
parking brake is always possible.
Application
With the vehicle stationary, to apply the
parking brake whether the engine is
running or off, pull on control A .
The application of the parking brake
i s c o n fi r m e d b y : - the lighting of the warning lamp on control A and of
warning lamp P on the in-
strument panel,
- the display of a message "parking brake applied" on the instrument
panel screen.
When the driver’s door is
opened with the engine run-
ning, a beep is heard and
a message displayed if the parking
brake has not been applied.
Page 125 of 306
126
9
D R I V I N G
Dynamic emergency
braking
In the event of a failure of the vehicle’s
m a i n b r a k i n g s y s t e m o r i n a n e x c e p -
tional situation (e.g. driver taken ill,
under instruction, etc) pull and hold
control A to stop the vehicle.
The electronic stability programme
(ESP) provides stability during dynamic
emergency braking.
If the dynamic emergency braking
malfunctions, one of the following
messages will be displayed on the
instrument panel display:
- "Parking brake faulty".
- "Parking brake control faulty". If a failure of the ESP system
is signalled by the lighting
of this warning lamp, then
braking stability is not guar-
anteed. In this event, stability must
be assured by the driver by repeat-
ing alternate "pull release" actions on
control A .
The dynamic emergency
braking must only be used in
e x c e p t i o n a l c i r c u m s t a n c e s . Emergency parking brake
release
In the event of the electric parking
brake malfunctioning or the battery
r u n n i n g fl a t , a n e m e r g e n c y m a n u a l
device can unlock the parking brake.
Immobilise the vehicle, with the
e n g i n e r u n n i n g , b y e n g a g i n g fi r s t
g e a r ( m a n u a l g e a r b o x ) o r p o s i -
tion P ( a u t o m a t i c g e a r b o x ) , t h e n
switch off the engine.
If it is impossible to immobilise the vehicle, do not action the
control and contact a CITROËN
dealer urgently.
Page 128 of 306
129
9
D R I V I N G
SITUATIONCONSEQUENCES
4
Display of messages " Parking brake faulty " ultyand " Anti roll-back fault " and of the following faultwarning lamps:
a n d / o r fl a s h i n g
- The automatic functions are deactivated.- The hill start assist is unavailable. To apply the electric parking brake: Immobilise the vehicle and switch off the ignition P u l l t h e c o n t r o l l e v e r f o r a t l e a s t 5 s e c o n d s o r u n t i l m a x i m u m application. Switch on the ignition and check that the electric parking brake warning lamps are on. - Application may take longer than in normal operation. - If warning lamp (!) fl a s h e s o r i f t h e w a r n i n g l a m p s d o n o t c o m e on when the ignition is switched on, this method does not work. Have it checked by a CITROËN dealer. on when the ignition is switched on, this method switched
To release the electric parking brake: Switch on the ignition. P u s h t h e c o n t r o l l e v e r a n d h o l d i t f o r a p p r o x i m a t e l y 3 s e c o n d s .
5
Display of message " Parking brake control faulty – automatic mode activated " and the following warning lamps:
a n d / o r fl a s h i n g
- Only the functions for automatic application on switching off the engine and automatic release on acceleration are available.
- Manual application/release of the electric parking brake anddynamic emergency braking are unavailable.
6
Display of message " Parking brake faulty " and of the following warning lamp:
fl a s h i n g
- Application of the parking brake is not guaranteed.
- The parking brake is temporarily unavailable.
It this situation arises:
W a i t a p p r o x i m a t e l y 3 m i n u t e s .
A f t e r 3 m i n u t e s , i f t h e w a r n i n g l a m p i s s t i l l fl a s h i n g , t r y t o r e i n i -tialise the parking brake, either by pushing and releasing th e control A while pressing the brake pedal or by means of a long pull on control A .
7
Battery fault-Lighting of the battery warning lamp makes it essential to stop t h e v e h i c l e a s s o o n a s t r a f fi c a l l o w s . S t o p a n d i m m o b i l i s e y o u r v e h i c l e .
-Apply the electric parking brake before switching o ff the engine.
Page 139 of 306
139
9
D R I V I N G In the event of a steep descent or
u n d e r e x c e s s i v e a c c e l e r a t i o n , t h e
speed limiter (which does not act
on the brakes) may not be able to
p r e v e n t t h e v e h i c l e f r o m e x c e e d i n g
the programmed speed.
U s e o f a fl o o r m a t o t h e r t h a n t h a t
recommended by CITROËN may
affect the normal operation of the
accelerator pedal and hamper the
operation of the speed limiter.
Floor mats approved by CITROËN
a r e fi t t e d w i t h a 3 r d fi x i n g l o c a t e d i n
the pedal area to avoid any risk of
interference with the pedals.
Suspension/Resumption
Press on button 3 .
This action causes the information
"PAUSE" to appear in zone A of the
instrument panel.
This action does not cancel the
m e m o r i s e d m a x i m u m s p e e d w h i c h
remains displayed in zone A of the
instrument panel. Overriding the programmed
speed
The accelerator pedal has an end-
o f - t r a v e l s w i t c h . I n o r d e r t o e x c e e d
t h e m e m o r i s e d m a x i m u m s p e e d a t
any time, you can press the pedal
all the way down. While the speed
i s b e i n g e x c e e d e d , t h e s p e e d d i s -
played in zone
A w i l l fl a s h . Y o u h a v e
only to release the accelerator pedal
t o r e t u r n b e l o w t h e m a x i m u m s p e e d ,
to restore the function.
T h e s p e e d w i l l a l s o fl a s h i f t h e s p e e d
limiter is not able to prevent the vehi-
c l e f r o m e x c e e d i n g t h e p r o g r a m m e d
speed (e.g. on a steep descent or
u n d e r e x c e s s i v e a c c e l e r a t i o n ) .
To reactivate the speed limiter, release
the accelerator to slow to a speed lower
than the programmed speed.
Return to normal driving
Either press on button 5 .
Or select the speed limiter function.
Or stop the engine.
Operating fault
If there is a malfunction, a message is
displayed accompanied by an audible
signal and lighting of the SERVICE
warning lamp.
Have it checked by a CITROËN
dealer.
Page 140 of 306
140
9
D R I V I N G
CRUISE CONTROL
System which automatically main-
tains the vehicle speed programmed
by the driver, without any action on
the accelerator pedal.
The cruise control is switched on
manually: the vehicle speed must be
at least 25 mph (40 km/h) and you
must be in at least:
- 4 t h g e a r f o r m a n u a l g e a r b o x e s ,
- 2 n d g e a r f o r a u t o m a t i c g e a r b o x e s . Displays on the instrument
panel
The programmed information is
grouped together in zone
A of the
instrument panel.
Programming
Press button 4 to select cruise
control mode " CRUISE ".
Steering wheel switches
The cruise control switches are lo-
cated on the left-hand side of the
steering wheel. T h e s e l e c t i o n i s c o n fi r m e d b y t h e
display of the function in zone
A of
the instrument panel.
When the function is selected, no
cruising speed has yet been
memorised. Once the desired speed has been
reached using the accelerator, press
button
1 or button 2 . The cruising
speed is then memorised and cruise
control is activated. The cruising
speed is displayed in zone A of the
instrument panel, and "ON" is dis-
played.
Adjustment of the memorised
speed while cruise control is
in operation
You can adjust the memorised
speed, displayed in zone A , by
pressing:
- Button 1 to increase the speed.
- Button 2 to reduce the speed.
Successive presses will modify the
cruise speed in steps of 1 mph and a
continuous press in steps of 5 mph.
You can then release the accelerator
pedal. The vehicle will automatically
keep to the speed chosen.
The vehicle speed may vary slightly
from that memorised.
If during cruise control the system
cannot keep to the cruise speed
(e.g. on a steep descent), then the
s p e e d fl a s h e s . I f n e c e s s a r y , b r a k e t o
curb your speed.