2008.5 Citroen C5 instrument panel
[x] Cancel search: instrument panelPage 118 of 306
120
8
S A F E T Y
* According to country.
Side airbags *
System which protects the driver
and front passenger in the event of
a serious side impact in order to limit
the risk of injury to the chest.
Each side airbag is incorporated in
the front seat back frame, on the
door side.
Activation
It is triggered unilaterally in the
event of a serious side impact ap-
plied to all or part of the side impact
zone
B , perpendicular to the longi-
tudinal centreline of the vehicle on
a horizontal plane and directed from
the outside towards the inside of the
vehicle.
T h e s i d e a i r b a g i n fl a t e s b e t w e e n t h e
front occupant of the vehicle and the
corresponding door trim pad. Impact detection zones
A. Front impact zone.
B. Side impact zone.
Curtain airbags *
System which protects the driver and p a s s e n g e r s ( w i t h t h e e x c e p t i o n o f t h e rear centre passenger) in the event of a serious side impact in order to limit the risk of head injuries.
Each curtain airbag is incorporated in the pillars and the upper part of the passenger compartment.
Operation
It is triggered at the same time as the corresponding side airbag in the event of a serious side impact to all or part of the side impact zone B , perpendi-cular to the longitudinal centreline of the vehicle on a horizontal plane and directed from the outside towards the inside of the vehicle.
T h e c u r t a i n a i r b a g i n fl a t e s b e t w e e n the front or rear occupant of the vehicle and the windows.
Operating fault
In the event of a minor impact or bump on the side of the vehicle or if the vehicle rolls over, the airbag may not be triggered.
The airbag is not triggered in the event of a rear or front collision.
If this symbol appears on
the instrument panel screen,
accompanied by an audible
signal and a message, con-
tact a CITROËN dealer to have the
system checked. The airbags may
no longer be triggered in the event
of a serious impact.
* According to country.
Page 121 of 306
123
9
D R I V I N G
ELECTRICPARKINGBRAKE
The electric parking brake combines
2 operational modes:
- AUTOMATIC
Automatic application when the engine stops and automatic re-
lease on use of the accelerator
(automatic operation by default),
- MANUAL
Manual application/release of the parking brake is always pos-
sible by pulling control A while
pressing the brake pedal. Automatic operation
Application with the engine off
With the vehicle stationary, the parking
brake
is automatically applied when
the engine is switched off.
The application of the parking brake
i s c o n fi r m e d b y : Application with the engine running
With the engine running and the ve-
hicle stationary, in order to immobi-
lise the vehicle you need to manually
apply the parking brake by
pulling
on control A .
The application of the parking brake
i s c o n fi r m e d b y :
- the lighting of the warning
lamp on control A and on
the instrument panel,
Before leaving the vehicle,
check that warning lamp P
on the instrument panel is
permanently lit.
Never leave a child alone inside the
vehicle with the ignition on, as they
could release the parking brake.
- the display of a message "parking
brake applied" on the instrument
panel screen.
T h e n o i s e o f o p e r a t i o n w i l l c o n fi r m t o
you the application/ release of your
electric parking brake. - the lighting of warning
lamp P on control A and
on the instrument panel,
- the display of a message "parking brake applied" on the instrument
panel screen.
When the driver’s door is opened, a
beep is heard and a message dis-
played if the parking brake has not
been applied.
Before leaving the vehicle,
check that warning lamp P
on the instrument panel is
permanently lit.
Page 122 of 306
124
9
D R I V I N G
Release
The electric parking brake releases
automatically and progressively
when you press the accelerator:
with a manual gearbox
( fi r s t gear or reverse gear engaged) ,
press down fully on the clutch
pedal then press on the accelera-
tor pedal and move off.
with an automatic gearbox , ac-
celerate with the selector in posi-
tion D , M or R .
Full release of the parking brake is
c o n fi r m e d b y : - the warning lamp P on
control A and on the in-
strument panel going out,
- the display of a message "parking brake released" on the instrument
panel screen.
When stationary, with the engine
running, do not press the accelerator
pedal unnecessarily (particularly
when starting the engine, including
in neutral), as you may release the
parking brake. Activation/Deactivation of the
automatic functions
The automatic application when the en-
gine is switched off and the automatic re-
lease when you press the accelerator can
be deactivated. Activation/deactivation is
p e r f o r m e d u s i n g t h e c o n fi g u r a t i o n m e n u
of the instrument panel screen. To do so,
s e l e c t " P e r s o n a l i s a t i o n / C o n fi g u r a t i o n /
D e fi n e t h e V e h i c l e p a r a m e t e r s / D r i v i n g
assistance/Automatic handbrake".
The deactivation of these
f u n c t i o n s i s c o n fi r m e d b y t h e
lighting of this warning lamp
on the instrument panel.
With the automatic functions deac-
tivated, the application and release
of the parking brake are done manu-
ally.
The deactivation of the auto-
matic functions is recommend-
ed in particularly cold conditions
(ice) and during towing (break-
down, caravan...).
Manual operation
Manual application/release of the
parking brake is always possible.
Application
With the vehicle stationary, to apply the
parking brake whether the engine is
running or off, pull on control A .
The application of the parking brake
i s c o n fi r m e d b y : - the lighting of the warning lamp on control A and of
warning lamp P on the in-
strument panel,
- the display of a message "parking brake applied" on the instrument
panel screen.
When the driver’s door is
opened with the engine run-
ning, a beep is heard and
a message displayed if the parking
brake has not been applied.
Page 123 of 306
124
9
D R I V I N G
Release
The electric parking brake releases
automatically and progressively
when you press the accelerator:
with a manual gearbox
( fi r s t gear or reverse gear engaged) ,
press down fully on the clutch
pedal then press on the accelera-
tor pedal and move off.
with an automatic gearbox , ac-
celerate with the selector in posi-
tion D , M or R .
Full release of the parking brake is
c o n fi r m e d b y : - the warning lamp P on
control A and on the in-
strument panel going out,
- the display of a message "parking brake released" on the instrument
panel screen.
When stationary, with the engine
running, do not press the accelerator
pedal unnecessarily (particularly
when starting the engine, including
in neutral), as you may release the
parking brake. Activation/Deactivation of the
automatic functions
The automatic application when the en-
gine is switched off and the automatic re-
lease when you press the accelerator can
be deactivated. Activation/deactivation is
p e r f o r m e d u s i n g t h e c o n fi g u r a t i o n m e n u
of the instrument panel screen. To do so,
s e l e c t " P e r s o n a l i s a t i o n / C o n fi g u r a t i o n /
D e fi n e t h e V e h i c l e p a r a m e t e r s / D r i v i n g
assistance/Automatic handbrake".
The deactivation of these
f u n c t i o n s i s c o n fi r m e d b y t h e
lighting of this warning lamp
on the instrument panel.
With the automatic functions deac-
tivated, the application and release
of the parking brake are done manu-
ally.
The deactivation of the auto-
matic functions is recommend-
ed in particularly cold conditions
(ice) and during towing (break-
down, caravan...).
Manual operation
Manual application/release of the
parking brake is always possible.
Application
With the vehicle stationary, to apply the
parking brake whether the engine is
running or off, pull on control A .
The application of the parking brake
i s c o n fi r m e d b y : - the lighting of the warning lamp on control A and of
warning lamp P on the in-
strument panel,
- the display of a message "parking brake applied" on the instrument
panel screen.
When the driver’s door is
opened with the engine run-
ning, a beep is heard and
a message displayed if the parking
brake has not been applied.
Page 124 of 306
125
9
D R I V I N G
Release
With the ignition on or the engine
running, to release the parking
brake, press on the brake pedal,
push then release control A .
The full application of the parking
b r a k e i s c o n fi r m e d b y : - the warning lamp on con-trol A and the warning
lamp P on the instrument
panel going off,
- the display of a message "parking brake released" on the instrument
panel screen.
If you push control A without pressing
the brake pedal, the parking brake
will not be released and the message
"Foot on brake necessary" will be
displayed on the instrument panel.
When stationary, with the
engine running, do not
press the accelerator pedal
unnecessarily, as you may
release the parking brake. Maximum application
If necessary, you can utilise
maxi-
mum application of the parking
brake. It is obtained by means of a
long pull on control A , until you see
t h e m e s s a g e " M a x a p p l i c a t i o n o f t h e
parking brake" and a beep is heard.
Maximum application is essential:
- in the case of a vehicle towing a caravan or a trailer, if the auto-
matic functions are activated
but you are applying the parking
brake manually,
- when the gradient you are parked on is variable in its effect (e.g. on
a ferry, in a lorry, during towing).
- in the case of towing, a loaded vehicle or parking on a gradient,
turn the front wheels towards the
pavement and engage a gear
when you park.
- a f t e r a m a x i m u m a p p l i c a t i o n , t h e release time will be longer. Particular situations
In certain situations (starting the en-
gine...), the parking brake can auto-
matically alter its level of application.
This is normal operation.
To advance your vehicle a few cen-
timetres without starting the engine,
but with the ignition on, press on the
brake pedal and release the parking
brake
by pushing then releasing
control A .
The full release of the parking brake
i s c o n fi r m e d b y t h e w a r n i n g l a m p P
(red) on the instrument panel going
off and the display of a message
"parking brake released" on the in-
strument panel screen.
If the parking brake malfunctions
while applied or if the battery runs
fl a t , a n e m e r g e n c y r e l e a s e i s a l w a y s
possible.
To guarantee correct operation of
the parking brake and therefore
your safety, the number of succes-
sive application/release operations
is limited to eight.
I f t h i s n u m b e r i s e x c e e d e d , y o u a r e
warned by the message "Parking
brake faulty" and a warning lamp
fl a s h e s .
Page 125 of 306
126
9
D R I V I N G
Dynamic emergency
braking
In the event of a failure of the vehicle’s
m a i n b r a k i n g s y s t e m o r i n a n e x c e p -
tional situation (e.g. driver taken ill,
under instruction, etc) pull and hold
control A to stop the vehicle.
The electronic stability programme
(ESP) provides stability during dynamic
emergency braking.
If the dynamic emergency braking
malfunctions, one of the following
messages will be displayed on the
instrument panel display:
- "Parking brake faulty".
- "Parking brake control faulty". If a failure of the ESP system
is signalled by the lighting
of this warning lamp, then
braking stability is not guar-
anteed. In this event, stability must
be assured by the driver by repeat-
ing alternate "pull release" actions on
control A .
The dynamic emergency
braking must only be used in
e x c e p t i o n a l c i r c u m s t a n c e s . Emergency parking brake
release
In the event of the electric parking
brake malfunctioning or the battery
r u n n i n g fl a t , a n e m e r g e n c y m a n u a l
device can unlock the parking brake.
Immobilise the vehicle, with the
e n g i n e r u n n i n g , b y e n g a g i n g fi r s t
g e a r ( m a n u a l g e a r b o x ) o r p o s i -
tion P ( a u t o m a t i c g e a r b o x ) , t h e n
switch off the engine.
If it is impossible to immobilise the vehicle, do not action the
control and contact a CITROËN
dealer urgently.
Page 126 of 306
127
9
D R I V I N G
Fetch the vehicle chock located
in the boot.
Immobilise the vehicle by placing
the chock at the front or at the
rear of one of the rear wheels.
Open the lower compartment of
the centre armrest by pulling it.
Ensure that the cup holder B is
folded away.
Remove the rubber mat covering
the base of the armrest. This strap does not permit
application of the parking
brake.
To re-engage the electric parking
brake (after rectifying the malfunc-
tion or battery failure), give a long
pull on the control A until the parking
b r a k e w a r n i n g l a m p ( ! ) fl a s h e s o n t h e
instrument panel then give a second
long pull until this warning lamp is lit
permanently.
The time required for the subse-
quent application may be longer
than during normal operation.
It is essential that the ignition is
not switched on until the parking
b r a k e h a s r e - e n g a g e d ( fl a s h i n g o f
the warning lamp (!) on the instru-
ment panel then warning lamp lit
permanently) to avoid damage to
the parking brake.
Take care not to allow moisture or
d u s t i n t h e p r o x i m i t y o f t h e d i a g n o s t i c
socket D which is essential for the
maintenance of your vehicle.
Release the strap from its loca-
tion C .
Pull the strap to release the
b r a k e . A l o u d k n o c k c o n fi r m s t h e
release of the brake.
Take care to put the strap
back in its location C correctly.
Otherwise, it will no longer be
possible to apply the brake.
Consult a CITROËN dealer.
Put the rubber mat back in place
on the base of the armrest.
Remove and stow the chock.
Page 129 of 306
130
9
D R I V I N G
HILL START ASSIST
System which keeps your vehicle
i m m o b i l i s e d t e m p o r a r i l y ( a p p r o x i -
mately 2 seconds) when starting on
a gradient, the time it takes to move
your foot from the brake pedal to the
accelerator pedal.
This function is only active when:
- the vehicle is completely stationary, with your foot on the brake pedal,
- in particular conditions on a slope,
- with the driver’s door closed.
The hill start assist function cannot
be deactivated. Operation
On an ascending slope, with the
vehicle stationary, the vehicle is
held for a brief moment when you
release the brake pedal:
- p r o v i d e d y o u a r e i n fi r s t g e a r o r n e u t r a l o n a m a n u a l g e a r b o x ,
- provided you are in D or M on an
a u t o m a t i c g e a r b o x .
On a descending slope, with the
vehicle stationary and reverse
gear engaged, the vehicle is held
for a brief moment when you
release the brake pedal.
D o n o t e x i t t h e v e h i c l e
while it is being held in the
hill start assist phase.
I f y o u n e e d t o e x i t t h e v e h i c l e w i t h t h e
engine running, manually apply the
parking brake and ensure that the
parking brake warning lamp (on the
instrument panel) and the warning
lamp P (on the control lever A ) are
permanently on.