2008.5 Citroen C5 DAG battery
[x] Cancel search: batteryPage 13 of 306
3 1
1
I N S T R U M E N T S a n d C O N T R O L S
Engine autodiagnostics system I f t h i s c o m e s o n , i t i n d i c a t e s
the occurrence of a fault in
t h e e n g i n e m a n a g e m e n t
s y s t e m .
I f i t fl a s h e s , i t i n d i c a t e s t h e o c c u r r e n c e o f
a f a u l t i n t h e e m i s s i o n c o n t r o l s y s t e m .
Maximum coolant temperature I f t h i s c o m e s o n , i t i n d i c a t e s
t h a t t h e t e m p e r a t u r e i n t h e
c o o l i n g s y s t e m i s t o o h i g h .
S t o p t h e v e h i c l e i m m e d i a t e l y
a n d a s s a f e l y a s p o s s i b l e .
Check the coolant level.
I f t h e l e v e l i s l o w , c o n t a c t a C I T R O Ë N
dealer.
Fuel low
I f t h i s c o m e s o n , i t i n d i c a t e s
t h a t t h e r a n g e r e m a i n i n g
i s a p p r o x i m a t e l y 3 0 m i l e s
( 5 0 k m ) .
I t m a y b e l e s s t h a n t h i s i n c e r t a i n
driving conditions and depending on
the engine.
T h e c a p a c i t y o f t h e t a n k i s a p p r o x i -
m a t e l y 7 1 l i t r e s . Battery charge
I f t h i s c o m e s o n , i t i n d i -
cates the occurrence of a
f a u l t i n t h e b a t t e r y c h a r g i n g
c i r c u i t ( d i r t y o r l o o s e t e r m i -
n a l s , s l a c k o r c u t a l t e r n a t o r
b e l t . . . ) .
Seat belt not fastened/
unfastened *
* A c c o r d i n g t o c o u n t r y .
T h i s w a r n i n g l a m p l i g h t s
u p o n t h e i n s t r u m e n t p a n e l
t o r e m i n d t h e d r i v e r a n d a l l
p a s s e n g e r s t h a t t h e y m u s t
f a s t e n t h e i r s e a t b e l t .
I t i s l i n k e d t o t h e s e a t b e l t i n f o r m a -
t i o n g i v e n b y t h e r o o f c o n s o l e . Seat belt non-fastening/
unfastening
T h i s w a r n i n g l a m p
i n f o r m s y o u o f t h e
non-fastening and
unfastening of the
d r i v e r a n d p a s s e n g e r s e a t b e l t s .
The lit up positions represent the
p a s s e n g e r s w h o s e s e a t b e l t s a r e
n o t f a s t e n e d / u n f a s t e n e d .
D r i v e r ’ s s e a t b e l t n o t f a s t e n e d :
- T h e w a r n i n g l a m p l i g h t s u p b e - t w e e n 0 a n d 1 2 m p h ( 2 0 k m / h ) .
A b o v e 1 2 m p h , i t fl a s h e s a c c o m p a -
n i e d b y a s o u n d s i g n a l f o r a r o u n d
1 2 0 s e c o n d s .
F r o n t a n d r e a r p a s s e n g e r s e a t b e l t s
not fastened:
-
W h e n t h e i g n i t i o n i s s w i t c h e d o n ,
the points corresponding to the seat
p o s i t i o n s w i t h s e a t b e l t s n o t f a s -
t e n e d r e m a i n l i t u p f o r 3 0 s e c o n d s .
S e a t b e l t s u n f a s t e n e d d u r i n g t h e
j o u r n e y :
- The point corresponding to the s e a t p o s i t i o n w i t h s e a t b e l t u n -
f a s t e n e d l i g h t s u p b e t w e e n 0 a n d
1 2 m p h ( 2 0 k m / h ) . A b o v e 1 2 m p h ,
i t fl a s h e s a c c o m p a n i e d b y a s o u n d
s i g n a l f o r a r o u n d 1 2 0 s e c o n d s .
The sound signal stops when the
s e a t b e l t i s r e - f a s t e n e d o r i f a d o o r
is opened.
Page 36 of 306
54
3
C O M F O R T
Press button 3 several times
until the programme number
corresponding to the required
programme time is displayed.
The chosen pre-selected time
is activated automatically after
10 seconds if no other buttons
have been pressed.
T o c o n fi r m t h a t t h e m o d e i s a c t i v a t -
ed, symbols 4 and 8 fl a s h u n t i l t h e
heating starts up.
When the heating starts up, the
warning lamp 9 lights up on the
dashboard and the programmer
screen.
Press button 3 b r i e fl y : t h e d i s p l a y
of the start-up time goes off.
In the event of a battery failure, the
factory settings are restored.
Stopping the heating system
while operating
Press button 5 .
The warning lamp 8 and the screen
go out. When a programme is operating,
pressing button
2 or 7 displays the
heating start-up time. A second
press on these buttons displays the
time.
When a programme is not operat-
ing, pressing button 2 or 7 displays
the time.
When the heating is operating, the
remaining operating duration is dis-
played instead of the time.
Page 41 of 306
59
3
C O M F O R T
Storing driving positions
System which takes into account the
settings of the driver's seat, exterior
mirrors and air conditioning. It ena-
bles you to store up to two positions
using the buttons on the side of the
driver's seat. Storing a position
Using buttons M/1/2
Switch on the ignition.
Adjust your seat and your exte-
rior mirrors.
Press button M , then press but-
ton 1 or 2 within four seconds.
An audible signal is heard indi- cating that the storing has been
taken into account.
Storing a new position cancels the
previous position.
Recalling a stored position
Ignition on or engine running
B r i e fl y p r e s s b u t t o n 1 or 2 to re-
call the corresponding position.
An audible signal is heard indicating
the end of the adjustment.
When the ignition is on, after a few
consecutive position recalls, the
function will be deactivated until the
engine is started, to prevent dis-
charging of the battery. For your safety, avoid storing a
driving position while driving.
REAR HEAD RESTRAINTS
The rear head restraints can be re-
moved and have two positions;
- high, position for use,
- low, storage position.
To raise a head restraint, pull it up-
wards.
To lower it, press the lug then the
head restraint.
To remove it, place it in the high po-
sition, push the lug and pull it up-
wards.
T o r e fi t i t , e n g a g e t h e h e a d r e s t r a i n t
rods in the holes taking care to re-
main in the centreline of the seat
back.
Never drive with the head restraints
removed, they must be in place
and correctly adjusted.
Page 42 of 306
59
3
C O M F O R T
Storing driving positions
System which takes into account the
settings of the driver's seat, exterior
mirrors and air conditioning. It ena-
bles you to store up to two positions
using the buttons on the side of the
driver's seat. Storing a position
Using buttons M/1/2
Switch on the ignition.
Adjust your seat and your exte-
rior mirrors.
Press button M , then press but-
ton 1 or 2 within four seconds.
An audible signal is heard indi- cating that the storing has been
taken into account.
Storing a new position cancels the
previous position.
Recalling a stored position
Ignition on or engine running
B r i e fl y p r e s s b u t t o n 1 or 2 to re-
call the corresponding position.
An audible signal is heard indicating
the end of the adjustment.
When the ignition is on, after a few
consecutive position recalls, the
function will be deactivated until the
engine is started, to prevent dis-
charging of the battery. For your safety, avoid storing a
driving position while driving.
REAR HEAD RESTRAINTS
The rear head restraints can be re-
moved and have two positions;
- high, position for use,
- low, storage position.
To raise a head restraint, pull it up-
wards.
To lower it, press the lug then the
head restraint.
To remove it, place it in the high po-
sition, push the lug and pull it up-
wards.
T o r e fi t i t , e n g a g e t h e h e a d r e s t r a i n t
rods in the holes taking care to re-
main in the centreline of the seat
back.
Never drive with the head restraints
removed, they must be in place
and correctly adjusted.
Page 51 of 306
68
4
A C C E S S
Malfunction
Following disconnection of the ve-
hicle battery, replacement of the re-
mote control battery or in the event
of a remote control malfunction, you
can no longer unlock, lock or locate
your vehicle.
First of all, use the key in the lock
to unlock or lock your vehicle.
Then, reinitialise the remote control.
If the problem persists, contact a
CITROËN dealer as soon as possible.
Reinitialisation
Switch off the ignition.
Turn the key to position 2
(Ignition) .
Press the closed padlock imme-
diately for a few seconds, until
the operation requested is trig-
gered.
Switch off the ignition and remove
the key from the ignition switch.
The remote control is fully opera-
tional again. Battery ref.: CR0523/3 volts.
This replacement battery is avail-
able from CITROËN dealers.
I f t h e b a t t e r y i s fl a t ,
you are informed by
lighting of this warning
light, an audible signal
and a message on the multifunction
display.
Unclip the casing using a coin at
the notch.
S l i d e t h e fl a t b a t t e r y o u t o f i t s
location.
Slide the new battery into its
location observing the original
direction.
Clip the casing.
Reinitialise the remote control.
Changing the battery
Page 56 of 306
70
4
A C C E S S
ALARM
System which protects and provides
a deterrent against the theft of your
vehicle. It provides two types of pro-
tection, exterior and interior, as well
as an anti-tamper function.
Exterior protection
The system monitors any opening of
the vehicle.
The alarm is triggered if anyone tries
to enter the vehicle by forcing a door,
the boot or the bonnet.
Interior protection
The system monitors any variation
in the volume in the passenger com-
partment.
The alarm is triggered if anyone
breaks a window or moves inside
the vehicle.
If you wish to leave a pet in the vehicle
or a window partially open, deactivate
the interior protection.
Anti-tamper function
The system monitors any putting out
of service of its components.
The alarm is triggered if anyone
tries to put the wires of the siren, the
central control or the battery out of
service.
D o n o t m a k e a n y m o d i fi c a t i o n s t o
the alarm system, this could cause
malfunctions. Locking the vehicle with full
alarm
Activation
Switch off the ignition and get out
of the vehicle.
Lock or deadlock the vehicle using
the locking button on the remote
control.
The alarm is activated; the indicator
light on button A fl a s h e s o n c e p e r
second.
Deactivation
Unlock the vehicle using the
unlocking button on the remote
control.
The alarm is deactivated; the indicator
light on button A switches off. Locking the vehicle with
exterior protection alarm only
Deactivation of the interior
protection
Switch off the ignition.
Within ten seconds, press button A
until the indicator light is lit continu-
ously.
Get out of the vehicle.
Lock or deadlock the vehicle using
the locking button on the remote
control.
The exterior protection alarm alone
remains activated; the indicator light
on button A fl a s h e s o n c e p e r s e c o n d .
In order to be taken into account, this
deactivation must be carried out each
time the ignition is switched off.
Reactivation of the interior
protection
Unlock the vehicle using the
unlocking button on the remote
control.
Relock the vehicle using the re-
mote control.
The alarm is activated again with
both types of protection; the indicator
light on button A switches off.
Page 57 of 306
71
4
A C C E S S
Triggering
This is indicated by sounding of the
s i r e n a n d fl a s h i n g o f t h e d i r e c t i o n
indicators for approximately thirty
seconds.
After it has been triggered, the alarm
is again operational.
If the alarm is triggered ten times in
succession, the eleventh time will
result in it becoming inactive. If the indicator light on button A
fl a s h e s r a p i d l y , t h i s i n d i c a t e s t h a t
the alarm was triggered during
your absence. When the ignition is
s w i t c h e d o n , t h i s fl a s h i n g s t o p s i m -
mediately.
To avoid triggering the alarm when
washing your vehicle, lock it using
the key.
Do not activate the alarm before
disconnecting the battery, otherwise
the siren will sound. Failure of the remote control
Unlock the vehicle using the key
in the driver's door lock.
Open the door; the alarm is trig-
gered.
Switch on the ignition; the alarm
stops.
Locking the vehicle without
alarm
Lock or deadlock the vehicle using
the key in the driver's door lock.
* According to country.
Malfunction
When the ignition is switched on,
lighting of the indicator light on button
A for ten seconds indicates a siren
fault.
Have it checked by a CITROËN
dealer. Automatic operation *
Depending on the legislation in force
in your country, one of these cases
may occur:
- 45 seconds after the vehicle is
locked using the remote control,
the alarm is activated, regardless
of the status of the doors and
boot.
- 2 minutes after the last door or the boot is closed, the alarm is
activated.
To avoid triggering the alarm
o n e n t e r i n g t h e v e h i c l e , fi r s t
press the unlocking button on
the remote control.
Page 61 of 306
75
4
A C C E S S
Unlocking
Press button A again to unlock
the vehicle.
The red indicator light on the button
switches off.
If the vehicle is locked or dead-
locked from the outside, the red
i n d i c a t o r l i g h t fl a s h e s a n d b u t t o n A
is inactive.
In this case, use the remote
control or the key to unlock the
vehicle.
Automatic centralised control
System which provides full automatic
locking or unlocking of the doors and
the boot while driving.
You can activate or deactivate this
function. Locking
When the speed exceeds 6 mph
(10 km/h), the doors and the boot
lock automatically.
If one of the doors is open, the auto-
matic central locking does not take
place.
If the boot is open, the automatic
central locking of the doors is active.
Unlocking
Above 6 mph (10 km/h), press
button A to unlock the doors and
the boot temporarily.
Activation
Press button A for more than
two seconds.
A c o n fi r m a t i o n m e s s a g e a p p e a r s
on the instrument panel display,
accompanied by an audible signal.
Deactivation
Press button A again for more
than two seconds.
A c o n fi r m a t i o n m e s s a g e a p p e a r s
on the instrument panel display,
accompanied by an audible signal. Emergency control
System which locks or unlocks the
doors mechanically in the event of
a malfunction of the battery or of the
central locking.
Locking the driver's door
Insert the key in the lock, then
turn it to the right.
Unlocking the driver's door
Insert the key in the lock, then
turn it to the left.
Locking the front and rear
passenger doors
Insert the key in the lock, located
on the edge of the door, then turn
it one eighth of a turn .
Unlocking the front and rear
passenger doors
Pull the interior door opening
control.