2008.5 Citroen C4 PICASSO fold seats

9
F A M I L I A R I S A T I O N
Fold the concertina plates ( 1 2 3 )
arranged on each of the third-row
seats.
Pull on the black belt F , located on the
seat backrest.

 64
Before moving the third-row seats,
do not forget to lock in the rigid
plates fi rst (located at the base of the
second-row seat backrests).
Installing the seats
Put the three sections of the concertina
plates ( 1 2 3 ) to their vertical position,
then pull on the red belt G .
Before moving the third-row seats,
return the rigid plates to the upright
position and lock them. Pull on control
E , located at the top of
the second-row seats backrest.

 63
I N T E R I O R
Stowing the seats Access to third-row seats
Do not leave objects either on or
underneath the second-row seats
when you are folding them. THIRD - ROW SEATS – GRAND C4 PICASSO

10
F A M I L I A R I S A T I O N
Folding the seats
From the boot - whilst loading,
for example (Grand C4 Picasso)
Take care to attach the third-row pas-
senger seat belts on the rings provided
for this purpose.

Do not attach the belts on the an-
choring points marked with a red
cross (see illustration above).

Stowing the tongue of the third-row
seat belt
SECOND - ROW SEATS

 120
Requirements for third-row
passenger seat belts
From outside

 Pull fi rmly upwards on strap C , as
indicated by the red arrow, to unlock
the seat; maintain the pressure until
the seat is fully folded.

 Slide latch A of the plate down-
wards, to unlock it.

 Return the plate to the upright posi-
tion, then slide latch A upwards to
lock it.
Before deploying the rigid plates, check
that the second row seats are slid as far
back as possible.

 62
I N T E R I O R
THIRD - ROW SEATS – GRAND C4 PICASSO
Having fi rstly folded the third-row
seats.

 Pull on control D to unlock the
required seat.
Repositioning the seats
Return the rigid plates of the second-row
seats to their initial (upright) position and
lock them in position (Grand C4 Picasso).
Raise the backrest and push it backwards
until it locks in position. Rigid plate (Grand C4 Picasso)
A rigid plate is attached to each
second-row seat backrest.
Unlocking/Locking the rigid plate

61
III
C O M F O R T
SECOND ROW SEATS (C4 PICASSO)
Folding the seat
Each seat can be folded onto the
fl oor to enable you to modify your
vehicle’s interior space.

 Pull fi rmly upwards on strap C ,
as indicated by the red arrow,
to unlock the seat; maintain the
pressure until the seat is fully
folded.

 Push the backrest slightly
forwards so that the backrest
pivots, folding onto the seat base.
The assembly then lowers onto
the fl oor. Repositioning seat

 Raise the backrests and push
them rearwards so that they lock
in position .

Always supervise any movements
of seats by children. Plates behind the second
row seats
Plates below the second row seats
provide the bottom of the bootspace
with rigidity. They automatically
follow the seat movements (e.g.
longitudinal adjustment, folding).
A storage area is available under-
neath the plates.

62
III
C O M F O R T
SECOND ROW SEATS (GRAND C4 PICASSO)
Each seat can be folded onto the
fl oor to form a fl at surface, thus
enabling you to modify your vehi-
cle’s interior space.
Folding the seat
From the exterior

 Pull fi rmly upwards on strap C ,
as indicated by the red arrow,
to unlock the seat; maintain the
pressure until the seat is fully
folded.

 Push the backrest slightly
forwards, so that the backrest
pivots, folding onto the seat
base. The assembly will then
lower onto the fl oor. From the boot
(when loading, for example)
You can fold the second-row seat(s)
from the boot, having fi rst folded the
third-row seats.

 Pull on the control D to unlock
the chosen seat, push the back-
rest gently forwards.
To prevent any damage to the mechanism, the control D unclips
under excessive force. Simply
reclip it to render the system op-
erational.
Repositioning the seat

 Return the second-row seat bas-
es to their initial position and lock
them in that position.

 Raise the backrests and push
them rearwards so that they lock
in position.
Before moving the third-row seats,
return the second-row rigid plates
to their initial position and lock
them.
Emergency exit: should the fi rst
system fail (control C ), the control

D is available for use by third-row
passengers to accelerate their
exit.

Always supervise any move-
ments of seats by children. Rigid plate
Each second-row seat backrest has
a rigid plate attached.
This plate enables you:
- to have a continuous load sur-
face in the boot, whatever the
positions of the seats,
- to avoid having objects sliding under the second-row seats.
Unlocking/Locking the rigid plate

 Slide the latch 1 on the plate
downwards, to unlock.

 Return the plate to the upright
position, then slide the latch 1
upwards, to lock.
Before deploying the rigid plates,
check that the second-row seats are
slid as far as possible rearwards.
5-seater confi gurations do not have
these rigid plates.

63
III
C O M F O R T
"Cinema seat" position
This position allows you to free up
space between the fi rst row and the
second row.
Pull the control E under the seat.
This position is only possible with
the lateral seats. Access to the third row seats
The third-row seats can be accessed
via the lateral second-row seats.

 Pull the control E . The seat un-
locks and the seat base comes
up against the backrest.

 Hold the control E in the raised
position, pushing forwards. The
whole seat slides towards the
front seat.
Space becomes free behind the
seat, the third-row passengers can
get to their seats. Exit from the third row seats

 Hold the control E in the raised
position. The seat unlocks and
the seat base comes up against
the backrest.

 Push the seat backrest, still hold-
ing the control E in the raised po-
sition.
If the table on the back of the fi rst-
row seat is down, close it to enable
this operation.
Repositioning the seat, from
the exterior, with the door open
If there are passengers seated in
the third row:

 manually return the assembly as
far as possible rearwards; the
seat does not return as far as
the maximum rearwards position
so as to retain leg space for the
third-row passengers,

 fold the seat base.

64
III
C O M F O R T
THIRD ROW SEATS (GRAND C4 PICASSO)
Concertina plates
Two rigid concertina plates, which
cannot be separated from the vehi-
cle, cover the 2 third-row seats, when
these are in the folded position.
Folding the concertina plates
Pull on the control, the 3 sections of
the plate will fold like a concertina.
When the third-row seats are up-
right, these concertina plates can be
left either:
- fl at behind the seats,
- in the vertical position,
thereby leaving a storage area
available. Unfolding the seat

 Return the second-row rigid
plates to their initial position and
lock them.

 Having folded your concertina
plate, pull on the control F lo-
cated behind the seat backrest.
The backrest pivots rearwards,
pulling the seat base with it. The
seat locks in the open position.
Repositioning the seat

 Return the second-row rigid
plates to their initial position and
lock them.

 Lower the head restraints.

 Correctly position the concertina
plate vertically behind the seat. Before moving the third-row seats,
return the rigid plates of the sec-
ond-row seats to the upright posi-
tion and lock them.
Do not try to fold a third-row seat
that has not fi rst had the backrest
fully locked in place.
Do not leave objects either on or
underneath the seat bases of the
third-row seats when you are fold-
ing them.
Do not leave your hand on the con-
trol
G as you fold the seats, as you
risk trapping your fi ngers.

 Pull on the control G , located at
the bottom of the seat backrest.
The seat unlocks.

 Next push the backrest gently
forwards. The backrest pivots,
folding onto the seat base. The
seat base then folds into the
stowage area provided for that
purpose.

 Reposition the concertina plates
over the folded seats.

82
IV
A C C E S S
Tailgate release
System for mechanical unlocking of
the boot in the event of a battery or
central locking malfunction.
Unlocking

 Fold back the rear seats to gain
access to the lock from inside
the boot.

 Insert a small screwdriver into
hole A of the lock to unlock the
tailgate.

 Push the white part, located in-
side the lock, to the left to unlock
the boot.
PANORAMIC GLASS ROOF
System which consists of a pano-
ramic tinted glass surface to in-
crease the light and visibility in the
passenger compartment.
Fitted with an electric blind in several
sections to improve temperature and
noise related comfort.
Opening the roof blind

 Rotate the control B to slide the
roof blind to the position desired
(positions 1 to 9 ). Closing the roof blind

 Rotate the control B to position 0
to close the roof blind.

Recommendations
- Pressing the locking button on the remote control for more than
two seconds will close the blind
(practical when, for example,
you leave your vehicle on a sun-
lit carpark).
- On returning to your vehicle, a press on the button B reposi-
tions the blind to the last position
selected.
Anti-pinch
The blind has an anti-pinch function.
At the end of its travel, when the blind
encounters an obstacle on closing, it
stops and moves back slightly.
Following a fault or after a battery
disconnection during the movement
of the blind or after it has stopped,
you have to re-initialise the anti-
pinch function:

 place the blind in the closed
position,

 press button B for approximately
two seconds.

82
IV
A C C E S S
Tailgate release
System for mechanical unlocking of
the boot in the event of a battery or
central locking malfunction.
Unlocking

 Fold back the rear seats to gain
access to the lock from inside
the boot.

 Insert a small screwdriver into
hole A of the lock to unlock the
tailgate.

 Push the white part, located in-
side the lock, to the left to unlock
the boot.
PANORAMIC GLASS ROOF
System which consists of a pano-
ramic tinted glass surface to in-
crease the light and visibility in the
passenger compartment.
Fitted with an electric blind in several
sections to improve temperature and
noise related comfort.
Opening the roof blind

 Rotate the control B to slide the
roof blind to the position desired
(positions 1 to 9 ). Closing the roof blind

 Rotate the control B to position 0
to close the roof blind.

Recommendations
- Pressing the locking button on the remote control for more than
two seconds will close the blind
(practical when, for example,
you leave your vehicle on a sun-
lit carpark).
- On returning to your vehicle, a press on the button B reposi-
tions the blind to the last position
selected.
Anti-pinch
The blind has an anti-pinch function.
At the end of its travel, when the blind
encounters an obstacle on closing, it
stops and moves back slightly.
Following a fault or after a battery
disconnection during the movement
of the blind or after it has stopped,
you have to re-initialise the anti-
pinch function:

 place the blind in the closed
position,

 press button B for approximately
two seconds.