2008.5 Citroen C4 PICASSO DAG wheel

170
XI
P R A C T I C A L I N F O R M A T I O N
Grand C4 Picasso C4 Picasso Access to the spare wheel
Taking out the wheel

 Move the third-row seat, right-
hand side (7 seater model).

 Retrieve the extension that is
attached to the rear of the seat
well.

 Engage the extension on the
pinion, located under the carpet
in the seat well.

 Using the wheel brace 4 on the
extension to turn the pinion
clockwise , release the cable
to lower the spare wheel to the
ground.

 Remove the wheel from under
the vehicle, disengaging the
linking plate in the centre of the
wheel.
The pinion to release the spare wheel
is located under the boot carpet, on
the right hand side in the wheel well
for the Grand C4 Picasso and on the
left hand side for the C4 Picasso. Putting the wheel back in place

 It is essential to direct the valve
upwards.

 Pass the linking plate through
the centre of the wheel (fi rst re-
moving the central trim on cer-
tain alloy wheels).

 Turn the pinion anti-clockwise
to draw in the cable. First the pin-
ion will turn idly, then the cable
will tighten to raise the wheel.
Check that the wheel is tight against the vehicle fl oor and
not interfering with other nearby
components (e.g. the exhaust).

 Stow the tools.
With the damaged wheel
now under the vehicle fl oor,
the vehicle has reduced
ground clearance, so take extra
care when reversing or driving on
uneven surfaces, including kerbs.
Retrieval of the spare wheel and
stowage of the affected road wheel
are operations that should be done
with the vehicle supported on its
wheels, not by the jack.

171
P R A C T I C A L I N F O R M A T I O N
Removing a wheel

 Park the vehicle on level, stable
and non-slippery ground. Apply
the parking brake (a message
and a warning lamp appear on
the instrument panel).
Switch off the ignition and engage fi rst gear or reverse gear depend-
ing on the slope (position P if an
automatic gearbox, D or R if a
6-speed electronic gearbox).

 Use a chock to secure the vehi-
cle more safely. Place the chock

7 in front of the wheel that is op-
posite the wheel affected.
 Detach the trim using the remov-
ing tool 4 , pulling in the area of
the valve.
For vehicles with alloy wheels, insert the trim removing tool 1
into the recess in the central trim
and lever it off.
For vehicles with alloy wheels that have visible bolts, remove
the chrome covers using the re-
moving tool 2 .
 Slacken the wheel bolts. For ve-
hicles with alloy wheels, undo
the anti-theft bolts using the anti-
theft socket 6 .

 Position the jack under the vehi-
cle, at the jacking point A closest
to the wheel to be changed.

 Unwind the jack 5 until its brack-
et is in contact with the ground.
Make sure that the jack is verti-
cal under the jacking point used.

 Continue to extend the jack so
as to raise the vehicle.

 Undo the wheel bolts and re-
move the wheel.
Before any operation of this
sort, it is advisable to deac-
tivate your pneumatic sus-
pension.

172
XI
P R A C T I C A L I N F O R M A T I O N
Wheel for temporary use
If your vehicle is equipped with a
spare wheel for temporary use only,
when fi tting this it is normal to observe
that the wheel bolts do not come to
bear directly on the wheel rim.
The spare wheel is secured by the
conical tapering of the wheel bolt’s
shaft.
When refi tting the original wheel, en-
sure that the wheel bolts and wash-
ers are clean and in good condition. Fitting a wheel

 Position the wheel with the aid of
the centring guide 3 .

 Do up the 3 bolts by hand, then
remove the centring guide 3 .
Position the 4 th bolt.

 Pre-tighten the wheel bolts, us-
ing the wheelbrace 4 .


Retract the jack 5 and disengage it.

 Tighten the wheel bolts, using
the wheelbrace 4 .

 Ensure that the tyre pressure is
correct.
Defl ation detection
Such wheels have tyre pressure
sensors. It is essential to have re-
pairs carried out by a CITROËN
dealer. The spare wheel does not
have a sensor.
Anti-theft bolts (alloy wheels)
Each wheel may be equipped with
one anti-theft bolt.
To remove it:

 Remove the protector that is cov-
ering it by means of the tool for
removing the chrome covers 2 .

 Use the anti-theft socket 6 with
the wheelbrace 4 . Dimension of the spare
wheel
If your spare wheel has dimensions
different from those of the normal ve-
hicle wheels (identifi ed by a label), it
is imperative to use the spare wheel
only temporarily, to drive with cau-
tion, not to exceed 80 km/h (50 mph)
and to have the tyre repaired and
the normal wheel refi tted as soon as
possible.
Tyre pressures
These are indicated on the label on the front left-hand door pillar (see section "Technical Specifi cation - § Vehicle Identifi cation ").
The wheel bolts are specifi c to each type of wheel.
If new wheels are fi tted, check with your CITROËN dealer that the If new wheels are fi tted, check If new wheels are fi tted, check
wheel bolts are compatible with the new wheels.
Note: take care to note down the code number on the head of the anti-theft bolt socket. This will ena-ble you to obtain a replacement anti-theft socket from a CITROËN ble you to obtain a replacement ble you to obtain a replacement
dealership.

172
XI
P R A C T I C A L I N F O R M A T I O N
Wheel for temporary use
If your vehicle is equipped with a
spare wheel for temporary use only,
when fi tting this it is normal to observe
that the wheel bolts do not come to
bear directly on the wheel rim.
The spare wheel is secured by the
conical tapering of the wheel bolt’s
shaft.
When refi tting the original wheel, en-
sure that the wheel bolts and wash-
ers are clean and in good condition. Fitting a wheel

 Position the wheel with the aid of
the centring guide 3 .

 Do up the 3 bolts by hand, then
remove the centring guide 3 .
Position the 4 th bolt.

 Pre-tighten the wheel bolts, us-
ing the wheelbrace 4 .


Retract the jack 5 and disengage it.

 Tighten the wheel bolts, using
the wheelbrace 4 .

 Ensure that the tyre pressure is
correct.
Defl ation detection
Such wheels have tyre pressure
sensors. It is essential to have re-
pairs carried out by a CITROËN
dealer. The spare wheel does not
have a sensor.
Anti-theft bolts (alloy wheels)
Each wheel may be equipped with
one anti-theft bolt.
To remove it:

 Remove the protector that is cov-
ering it by means of the tool for
removing the chrome covers 2 .

 Use the anti-theft socket 6 with
the wheelbrace 4 . Dimension of the spare
wheel
If your spare wheel has dimensions
different from those of the normal ve-
hicle wheels (identifi ed by a label), it
is imperative to use the spare wheel
only temporarily, to drive with cau-
tion, not to exceed 80 km/h (50 mph)
and to have the tyre repaired and
the normal wheel refi tted as soon as
possible.
Tyre pressures
These are indicated on the label on the front left-hand door pillar (see section "Technical Specifi cation - § Vehicle Identifi cation ").
The wheel bolts are specifi c to each type of wheel.
If new wheels are fi tted, check with your CITROËN dealer that the If new wheels are fi tted, check If new wheels are fi tted, check
wheel bolts are compatible with the new wheels.
Note: take care to note down the code number on the head of the anti-theft bolt socket. This will ena-ble you to obtain a replacement anti-theft socket from a CITROËN ble you to obtain a replacement ble you to obtain a replacement
dealership.

215
4
1
23
51
23
4
5
2
1
CONTROL SHORT-CUTS
STEERING WHEEL CONTROLS
1. Volume increase.
2. Volume decrease.
3. Mute.
4. RADIO: selection of the previous or next stored station. CD/MP3/USB: selection of the previous or next directory. CD CHANGER selection of the previous or next CD.
5. RADIO: automatic search for a higher frequenc y. CD/MP3/CD CHANGER/USB : selection of the next track.
CD/MP3/CD CHANGER: continuous press: fast forwards play.
1. Displays the main screen.
2. Selection of the type of information displayed on theright-hand side of the display for the monochrome d isplay A.
3. Abandon the operation in progress and return to the previous display.
4. Navigation through the menus.
5. Confi rmation of the function selected.
If your vehicle is fi tted with the Bluetooth system: pick up an incoming call or hang up a call which is in progress.
If your vehicle is fi tted with the Bluetooth syst em:
1. Activation of the voice recognition.
2. Displaying of the "PHONE BOOK" menu.

32
08
4
1
23
51
23
4
5
1
CONTROL SHORT-CUTS
STEERING WHEEL CONTROLS
1. Volume increase.
2. Volume decrease.
3. Mute.
4. RADIO: selection of the previous or next stored station. MP3/JUKEBOX: selection of the previous or next directory. CD CHANGER: selection of the previous or next CD.
5. RADIO: automatic search for a higher frequency. CD/MP3/JUKEBOX/CD CHANGER: selection of the next track. CD/MP3/CD CHANGER: continuous press: fast forwards play.
1. Displays the main screen.
2. Selection of the mode displayed (TRIP, TEL, NAV or AUDIO).
3. Abandon the operation in progress and return to the previous display.
4. Navigation through the menus.
5. Confi rmation of the function selected.
1. When the telephone is not in use = access to the telephone menu. Incoming call: short press to accept, long press to reject the call. Call in progress: short press to hang up, long press to access the telephone menu.

22
09
4
1
23
51
2
1
23
4
53
4
1
C4 STEERING WHEEL CONTROLS
STEERING WHEEL CONTROLS
1. Volume increase.
2. Volume decrease.
3. Successive presses mute/restore the sound.
4. Rotation - associated with a pop-up. Radio - access the 6 stored stations: higher or previous. Music players: previous/next track.
5. Radio: next/previous station. Music players: next track.
1. Press. Repeat the current spoken navigation instruction.
2. Short press to make a telephone call. Pick up/Hang up. Access the telephone menu. Display the call list. Long press to reject an incoming call.
3. Personalisation Short press to confi rm the choice made using the d ial.
4. Rotation. Movement on the call list in the phone book. Personalisation selection.
1. Short press: provides access to the menu according to the display on the screen. Short press: provides access to the menu according to the Short press: provides access to the menu according to the
2. Successive presses: provides access according to the current display on the screen. Successive presses: provides access according to the Successive presses: provides access according to the
MAP/NAV (if navigation is in progress), current display on the screen. urrent display
TEL (if a conversation is in progress), MAP/NAV (if navigation is in progress), MAP/NAV (if navigation is in progress),
RADIO or MEDIA in progress, Trip computer. TEL (if a conversation is in progress), TEL (if a conversation is in progress),
Long press: switch to black screen - Dark (night driving). RADIO or MEDIA in progress, Trip computer. RADIO or MEDIA in progress, Trip computer.
Touching a control restores the display. Long press: switch to black screen - Dark (night driving). Long press: switch to black screen - Dark (night driving).
3. ESC: abandon the current operation. 4. Rotation: selects the access to the short-cut menus according to the current display. 5. Confi rms the choice displayed on the screen.

23
09
LISTMENU
4
3
5
6
7
8
9
10
11
1
2
C5 STEERING WHEEL CONTROLS
STEERING WHEEL CONTROLS
1. Successive presses: "Black Panel" mode - black screen (night driving).
2. Short press to make a telephone call. Pick up/Hang up. Access the telephone menu. Display the call list. Long press to reject an incoming call.
3. Rotation: provides access to the short-cut menus a
ccording to the display on the screen. Short press: confi rm the choice displayed on the s creen. Long press: return to the main menu.
4. Short press: abandon the current operation. Reject an incoming call. Long press: return to the initial display.
5. Menu: provides access to the main menu.
6. VOL +: volume increase.
7. VOL -: volume decrease.
8. Successive presses: mute/restore sound.
9. Short press: Radio: higher frequency. Music players: next track. Long press for fast play.
10. Short press: Radio: lower frequency. Music players: previous track. Long press for fast play.
11. Short press: display the list of radio frequencies available or the list of tracks, albums, directories. Long press: update the list of stations received.
Press: repeat the current navigation instruction.
Successive presses: selection of the type of information present on the screen.