Page 308 of 576
4-47
ENGYPVS GOVERNOR
2. Install:
9Ball 1
9Retainer 2
To governor shaft 3.
NOTE:
Apply the transmission oil on the retainer and
ball.
3. Install:
9Dowel pin 1
NOTE:
9While compressing the spring, install the dowel
pin.
9Make sure the dowel pin fits into the groove a
in the retainer.
4. Install:
9Governor assembly 1
NOTE:
Align the groove ain the governor with the fork
band set the governor in the crankcase cover.
1C3-9-32-4C 4/6/06 2:13 PM Page 22
Page 310 of 576
4-48
ENGWATER PUMP
Extent of removal Order Part name Q’ty Remarks
WATER PUMP DISASSEMBLY
Preparation for Crankcase cover (right)
Refer to “KICK AXLE, SHIFT SHAFT AND
removalPRIMARY DRIVE GEAR” section.
1 Water pump housing cover 1
2 Impeller shaft gear 1
3 Dowel pin 1
4 Plain washer 1
5 Impeller shaft assembly 1
6 Bearing 1
Refer to “REMOVAL POINTS”.
7 Oil seal 2
EC4G0000
WATER PUMP
1
2
Extent of removal:1Impeller shaft removal2Oil seal removal
10 Nm (1.0 m•kg, 7.2 ft•lb)
10 Nm (1.0 m•kg, 7.2 ft•lb)
1C3-9-32-4C 4/6/06 2:13 PM Page 24
Page 312 of 576
4-49
ENGWATER PUMP
EC4G3000
REMOVAL POINTS
EC4G3210
Oil seal
NOTE:
9Replace the oil seal when transmission oil or
coolant leaks out from the water pump housing
hole at the bottom.
9Do not reuse the removed bearing and oil seal.
1. Remove:
9Bearing 1
2. Remove:
9Oil seal (outside) 1
9Oil seal (inside) 2
EC4G4000
INSPECTIONEC444200
Impeller shaft assembly
1. Inspect:
9Impeller shaft assembly1
Bend/Wear/Damage Replace.
Fur deposits Clean.
1C3-9-32-4C 4/6/06 2:13 PM Page 26
Page 314 of 576
4-50
ENGWATER PUMP
EC444300
Impeller shaft gear
1. Inspect:
9Gear teeth a
Wear/Damage Replace.
EC4H4600
Bearing
1. Inspect:
9Bearing 1
Rotate inner race with a finger.
Rough spot/Seizure Replace.
EC444400
Oil seal
1. Inspect:
9Oil seal 1
Wear/Damage Replace.
EC4G5000
ASSEMBLY AND INSTALLATION
EC4G5111
Oil seal
1. Install:
9Oil seal (inside) 1
9Oil seal (outside) 2
NOTE:
9Apply the lithium soap base grease on the oil
seal lip.
9Install the oil seal with its manufacture’s marks or
numbers facing the crankcase cover (right) 3.
2. Install:
9Bearing 1
NOTE:
Install the bearing by pressing its outer race par-
allel.
1C3-9-32-4C 4/6/06 2:13 PM Page 28
Page 316 of 576
4-51
ENGWATER PUMP
EC4G5220
Impeller shaft assembly
1. Install:
9Impeller shaft assembly1
NOTE:
9Take care so that the oil seal lip is not damaged
or the spring does not slip off its position.
9When installing the impeller shaft assembly,
apply the lithium soap base grease on the oil
seal lip and impeller shaft assembly. And install
the shaft while turning it.
2. Install:
9Plain washer 1
9Dowel pin 2
9Impeller shaft gear 3
9Collar 4
9Plain washer 5
9Circlip 6
NOTE:
Install the Impeller shaft gear with the dowel pin
fitted in the groove ain the same gear.
3. Install:
9Dowel pin 1
9Gasket (water pump housing cover) 2
4. Install:
9Water pump housing cover 1
9Bolt (water pump housing cover) 2
9Copper washer (coolant drain bolt) 3
9Coolant drain bolt 4
10 Nm (1.0 m•kg, 7.2 ft•lb)
10 Nm (1.0 m•kg, 7.2 ft•lb)
1C3-9-32-4C 4/6/06 2:13 PM Page 30
Page 336 of 576
4-61
ENGCRANKCASE AND CRANKSHAFT
Extent of removal Order Part name Q’ty Remarks
CRANKCASE AND CRANKSHAFT
REMOVAL
Preparation for Engine Refer to “ENGINE REMOVAL”section.
removal Piston Refer to “
CYLINDER HEAD, CYLINDER
AND PISTON
” section.
Primary drive gear
Kick idle gearRefer to “
KICK AXLE, SHIFT SHAFT AND
Stopper leverPRIMARY DRIVE GEAR”section.
Rotor and stator Refer to “CDI MAGNETO” section.
1 Segment 1 Refer to “REMOVAL POINTS”.
2 Bolt [L=45 mm (1.77 in)] 6
3 Bolt [L=55 mm (2.17 in)] 4
4 Bolt [L=65 mm (2.56 in)] 1
5 Bolt [L=75 mm (2.95 in)] 1
6 Holder 1
7 Crankcase (right) 1 Use special tool.
8 Crankcase (left) 1 Refer to “REMOVAL POINTS”.
9 Crankshaft 1 Use special tool.
Refer to “REMOVAL POINTS”.
10 Oil seal 2
11 Bearing 2 Refer to “REMOVAL POINTS”.
EC4N0000
CRANKCASE AND CRANKSHAFT
12
3
Extent of removal:1Crankcase separation2Crankshaft removal
3Crankshaft bearing removal
30 Nm (3.0 m•kg, 22 ft•lb)10 Nm (1.0 m•kg, 7.2 ft•lb)
20 Nm (2.0 m•kg, 14 ft•lb)
14 Nm (1.4 m•kg, 10 ft•lb)
1C3-9-32-4D 5/1/06 10:41 AM Page 12
Page 342 of 576
4-64
ENGCRANKCASE AND CRANKSHAFT
Standard
Runout 0.03 mm 0.05 mm
limit: (0.0012 in) (0.0020 in)
Small end 0.8~1.0 mm 2.0 mm
free play: (0.031~0.039 in) (0.08 in)
Side 0.06~0.64 mm
—
clearance: (0.002~0.025 in)
Crank 55.90~55.95 mm
—
width: (2.201~2.203 in)
2. Inspect:
9Bearings 1
Rotate inner race with a finger.
Rough spot/Seizure Replace.
3. Inspect:
9Oil seal 1
Damage Replace.
EC4N4202
Crankshaft
1. Measure:
9Runout limit a
9Small end free play limit b
9Connecting rod big end side clearance c
9Crank width d
Out of specification Replace.
Use the dial gauge and a thickness gauge.
EC4N5000
ASSEMBLY AND INSTALLATION
EC4N5300
Crankshaft bearing
1. Install:
9Bearing 1
To crankcase (left and right).
NOTE:
Install the bearing by pressing its outer race
parallel.
Dial gauge:
YU-3097/90890-01252
1C3-9-32-4D 5/1/06 10:41 AM Page 18
Page 344 of 576
4-65
ENGCRANKCASE AND CRANKSHAFT
EC4N5102
Oil seal
1. Install:
9Oil seal (left) 1
9Oil seal (right) 2
NOTE:
9Apply the lithium soap base grease on the oil
seal lip.
9Install the oil seal with its manufacture’s marks
or numbers facing outward.
EC4N5272
Crankshaft
1. Install:
9Crankshaft 1
Use the crankshaft installing tool 2, 3, 4
åFor USA and CDN
∫Except for USA and CDN
NOTE:
9Hold the connecting rod at top dead center with
one hand while turning the nut of the installing
tool with the other. Operate the installing tool
until the crankshaft bottoms against the bear-
ing.
9Before installing the crankshaft, clean the con-
tacting surface of crankcase.
9Apply molybdenum disulfide grease to the sur-
face awhere the crankshaft and bearing come
in contact.
9Apply the lithium soap base grease on the oil
seal lip.
cC
Do not use a hammer to drive in the crank-
shaft.
Crankshaft installing tool:
Pot
2 2
:YU-90050/90890-01274
Bolt 3 3
:YU-90050/90890-01275
Adapter 4 4
:YU-90063/90890-01278
å∫
1C3-9-32-4D 5/1/06 10:41 AM Page 20
