2007 YAMAHA XMAX 250 oil type

1. Engine oil filler cap - Dipstick
2. Maximum level mark
3. Minimum level mark
3. Wait a few minutes until the oil
settles, remove the oil filler cap,
wipe the dipstick clean, insert it
back into the oil filler hole (wit-
hout screwing it in), and then
remove it again to check the oil
level.
NOTE:
The engine oil should be between the
minimum and maximum level marks.
4. If the engine oil is below the mini-
mum level mark, add sufficient oil
of the recommended type to rai-
se it to the correct level.5. Insert the dipstick into the oil filler
hole, and then tighten the oil filler cap.
To change the engine oil
1. Start the engine, warm it up for
several minutes, and then turn it
off.
2. Place an oil pan under the engine
to collect the used oil.
1. Engine oil drain bolt
3. Remove the engine oil filler cap
and the engine oil drain bolt to
drain the oil from the crankcase.
1. Engine oil drain bolt
2. Washer
4. Check the washer for damage
and replace it if necessary.
5. Install the washer and the engine
oil drain bolt, and then tighten the
drain bolt to the specified torque.
NOTE:
Make sure that the washer is properly
seated.
6. Add the specified amount of the
recommended engine oil, and
then install and tighten the oil
filler cap.
Tightening torque:
Engine oil drain bolt:
20 Nm (2.0 m•kgf, 14.5 ft•lbf)
1
PERIODIC MAINTENANCE AND MINOR REPAIR
6-9
6
1C0-F8199-E3.qxd 2/11/06 20:46 Página 16

Before riding, check that the brake
fluid is above the minimum level mark
and replenish if necessary. A low bra-
ke fluid level may indicate worn brake
pads and/or brake system leakage. If
the brake fluid level is low, be sure to
check the brake pads for wear and
the brake system for leakage.
Observe these precautions:
When checking the fluid level,
make sure that the top of the bra-
ke fluid reservoir is level.
Use only the recommended qua-
lity brake fluid, otherwise the rub-
ber seals may deteriorate, cau-
sing leakage and poor braking
performance.
Refill with the same type of brake
fluid. Mixing fluids may result in a
harmful chemical reaction and
lead to poor braking performan-
ce.
Be careful that water does not
enter the brake fluid reservoir
when refilling. Water will signifi-
cantly lower the boiling point of
the fluid and may result in vapor
lock.
Brake fluid may deteriorate pain-
ted surfaces or plastic parts.
Always clean up spilled fluid
immediately.
As the brake pads wear, it is nor-
mal for the brake fluid level to
gradually go down. However, if
the brake fluid level goes down
suddenly, have a Yamaha dealer
check the cause.
EAU22720
Changing the brake fluid
Have a Yamaha dealer change the
brake fluid at the intervals specified in
the NOTE after the periodic mainte-
nance and lubrication chart. In addi-
tion, have the oil seals of the brake
master cylinder and caliper as well as
the brake hose replaced at the inter-
vals listed below or whenever they are
damaged or leaking.
Oil seals: Replace every two
years.
Brake hose: Replace every four
years.
Recommended brake fluid:
DOT 4
PERIODIC MAINTENANCE AND MINOR REPAIR
6-19
6
1C0-F8199-E3.qxd 2/11/06 20:46 Página 26

1. Headlight bulb cover
2. Headlight bulb holder
EWA10790
s sWARNING
Headlight bulbs get very hot. The-
refore, keep flammable products
away from a lit headlight bulb, and
do not touch the bulb until it has
cooled down.
4. Place a new headlight bulb into position, and then secure it with
the bulb holder.
1. Do not touch the glass part of the bulb.
ECA10650
CAUTION:
Take care not to damage the follo-
wing parts:
Headlight bulb
Do not touch the glass part of
the headlight bulb to keep it
free from oil, otherwise the
transparency of the glass, the
luminosity of the bulb, and the
bulb life will be adversely affec-
ted. Thoroughly clean off any
dirt and fingerprints on the
headlight bulb using a cloth
moistened with alcohol or thin-
ner.
Headlight lens
• Do not affix any type of tinted film or stickers to the head-
light lens.
• Do not use a headlight bulb of a wattage higher than spe-
cified.
5. Install the headlight bulb cover, and then connect the coupler.
6. Install the cowling.
7. Have a Yamaha dealer adjust the headlight beam if necessary.
1
2
PERIODIC MAINTENANCE AND MINOR REPAIR
6-26
6
1C0-F8199-E3.qxd 4/11/06 09:44 Página 33

DimensionsOverall length2210 mm (87.0 in)
Overall width 790 mm (31.1 in)
Overall height 1380 mm (54.3 in)
Seat height 785 mm (30.9 in)
Wheelbase 1545 mm (60.8 in)
Ground clearance 112.7 mm (4.44 in)
Minimum turning radius 3650 mm (143.7 in)
WeightWith oil and fuel176 kg (388 lb)
EngineEngine typeLiquid cooled 4-stroke, SOHC
Cylinder arrangement Forward-inclined single cylinder
Displacement 249.7 cm
3(15.24 cu*in)
Bore x stroke 69.0 x 66.8 mm (2.71 x 2.63 in)
Compression ratio 10:01
Starting system Electric starter
Lubrication system Wet sump
Oil type or gradeEngine oilSAE 10W30
Recommended engine oil grade API service SE, SF, SG type or higher
Engine oil quantityPeriodic oil change1.2 L (1.27 US qt) (1.06 Imp qt)
Final transmission oilTypeYAMALUBE 4 (10W30) of SAE10W30
type SE motorolie
Quantity 0.25 L (0.26 US qt) (0.22 Imp qt)
Cooling systemRadiator capacity (including all routes)0.34 L (0.36 US qt) (0.30 Imp qt)
Coolant reservoir capacity (up to the
maximum level mark) 0.26 L (0.23 Imp qt, 0.28 US qt)
Air filterAir filter elementDry element
Recommended fuelRecommended fuelUnleaded fuel
Fuel tank capacity 12.5 L (3.30 US gal) (2.75 Imp gal)
Fuel reserve amount 2 L (0.53 US gal) (0.44 Imp gal)
Fuel injectionManufacturerAISAN Type x quantity
EFI System x 1
Spark plug (s)Manufacturer/modelNGK/DPR8EA-9
Spark plug gap 0.8-0.9 mm (0.031-0.035 in)
ClutchClutch typeDry, automatic centrifugal
TransmissionPrimary reduction systemHelical gear
Primary reduction ratio 40/15 (2.666)
Secondary reduction system Helical gear
Secondary reduction ratio 40/14 (2.857)
Transmission type V-belt automatic
Operation Centrifugal automatic type
ChassisFrame typeSteel tube underbone
Caster angle 28 º
Trail 100 mm (3.94 in)
Front tireTypeTubeless
SPECIFICATIONS
8-1
8
1C0-F8199-E3.qxd 16/11/06 19:33 Página 1

Size120/70-15 M/C 56S(Michelin)
120/70-15 M/C 56P(Pirelli)
Manufacturer/model MICHELIN/GOLD STANDARD
PIRELLI/GTS23
Rear tireTypeTubeless
Size 140/70-14 M/C 68S(Michelin)
140/70-14 M/C 68P(Pirelli)
Manufacturer/model MICHELIN/GOLD STANDARD
PIRELLI/GTS24
LoadingMaximum load180 kg (396.9 lb)
Load is total weight of the equipement, dri-
ver, passenger and accessories
Tire air pressure (measured on cold
tires)
Loading condition 0–90 kg (0–198 lb)
Front 190 kPa (27 psi) (1.9 kgf/cm
2)
Rear 220 kPa (31 psi) (2.2 kgf/cm
2)
Loading condition 90 kg (198 lb)–Maximum load
Front 210 kPa (30 psi) (2.1 kgf/cm
2)
Rear 250 kPa (36 psi) (2.5 kgf/cm
2)
Front wheelWheel typeAluminium wheel
Rim size 15 x MT3.50
Rear wheelWheel typeAluminium wheel
Rim size 14 x MT3.75
Front brakeTypeSingle disc brake
Operation Right hand operation
Recommended fluid DOT 4
Rear brakeTypeSingle disc brake
Operation Left hand operation
Recommended fluid DOT 4
Front suspensionTypeTelescopic fork
Spring/shock absorber type Coil spring/oil damper
Wheel travel 110 mm (4.33 in)
Rear suspensionTypeUnit swing Spring/shock absorber type
Coil spring/oil damper
Wheel travel 95 mm (3.74 in)
Electrical systemIgnition systemTransistorized coil ignition (digital)
Charging system AC magneto
BatteryManufacturer/modelYuasa/YTX9-BS
Voltage, capacity 12 V, 8.0 Ah
Bulb voltage, wattage x quantity
Headlight12 V, 35.0 W / 35.0 W x 2
Auxiliary light 12 V, 5.0 W x 2
Tail/brake light 12 V, 21.0 W / 5.0 W x 2
Front turn signal light 12 V, 10.0 W x 2
Rear turn signal light 12 V, 10.0 W x 2
License plate light 12 V, 5.0 W x 1
Meter lighting LED
Fuel level warning lamp LED
High beam Indicator light LED
SPECIFICATIONS
8-2
8
1C0-F8199-E3.qxd 7/11/06 12:14 Página 2