2007 YAMAHA WOLVERINE 450 maintenance

8-40
8
EBU24390Checking the front brake lever free play The brake lever free play must be checked at the
intervals specified in the periodic maintenance and
lubrication chart. The brake lever should have a
free play of zero mm (zero in) as shown. If the free
play is incorrect, have a Yamaha dealer check the
brake system.
WARNING
EWB02070Operating with improperly serviced or adjust-
ed brakes could cause loss of braking ability,
which could lead to an accident.
After servicing:

Make sure the brakes operate smoothly and
that the free play is correct.
Make sure the brakes do not drag.
Make sure the brakes are not spongy. All air
must be bled from the brake system.
Replacement of brake components requires
professional knowledge. These proceduresshould be performed by a Yamaha dealer.EBU26491Adjusting the rear brake lever free play
and checking the brake pedal position The brake lever free play must be adjusted and
brake pedal position must be checked and, if nec-
essary, adjusted at the intervals specified in the
periodic maintenance and lubrication chart.NOTE:
Always perform this maintenance completely in
the following order whenever adjusting the rear
brake.
Before adjusting the brake lever free play and
checking the brake pedal position, check therear brake pads for wear.
1. Brake lever free playU3C261E0.book Page 40 Thursday, June 29, 2006 4:15 PM

8-42
8Checking the brake pedal position
The top of the brake pedal should be positioned
67.0–77.0 mm (2.64–3.03 in) above the top of the
footboard bracket. If the brake pedal position is in-
correct, have a Yamaha dealer adjust it.
WARNING
EWB02070Operating with improperly serviced or adjust-
ed brakes could cause loss of braking ability,
which could lead to an accident.
After servicing:
Make sure the brakes operate smoothly and
that the free play is correct.
Make sure the brakes do not drag.

Make sure the brakes are not spongy. All air
must be bled from the brake system.
Replacement of brake components requires
professional knowledge. These proceduresshould be performed by a Yamaha dealer.EBU24230Axle boots The axle boots must be checked for damage at the
intervals specified in the periodic maintenance and
lubrication chart. Check the axle boots for tears or
damage. If any damage is found, have them re-
placed by a Yamaha dealer.
1. Brake pedal position
1. Axle boot (each side)
U3C261E0.book Page 42 Thursday, June 29, 2006 4:15 PM

8-43
8
EBU24751Brake light switches The operation of the brake light switches must be
checked and, if necessary, adjusted at the inter-
vals specified in the periodic maintenance and lu-
brication chart.
The brake light switch for the brake pedal can be
adjusted as follows, but the other brake light
switches should be adjusted by a Yamaha dealer.
1. Remove panel A. (See page 8-8.)NOTE:The brake light switch is properly adjusted when
the brake light comes on just before braking takeseffect.
2. Turn the adjusting nut while holding the brake
light switch in place. To make the brake light
come on earlier, turn the adjusting nut in direc-
tion (a). To make the brake light come on lat-
er, turn the adjusting nut in direction (b).3. Install the panel.
EBU24900Checking and lubricating the cables The operation and the condition of all control ca-
bles should be checked before each ride, and the
cables and cable ends should be lubricated if nec-
essary. If a cable is damaged or does not move
smoothly, have a Yamaha dealer check or replace
it.1. Brake light switch
2. Brake light switch adjusting nutRecommended lubricant:
Engine oil
U3C261E0.book Page 43 Thursday, June 29, 2006 4:15 PM

8-45
8
EBU24961Checking the wheel bearings The front and rear wheel bearings must be
checked at the intervals specified in the periodic
maintenance and lubrication chart. If there is play
in a wheel hub or if a wheel does not turn smoothly,
have a Yamaha dealer check the wheel bearings.EBU24980Lubricating the drive shaft universal
joint The drive shaft universal joint must be lubricated at
the intervals specified in the periodic maintenance
and lubrication chart.
EBU25100Lubricating the steering shaft The steering shaft must be lubricated at the inter-
vals specified in the periodic maintenance and lu-
brication chart.EBU25222Battery This model is equipped with a sealed-type (MF)
battery, which does not require any maintenance.
There is no need to check the electrolyte or to add
distilled water. Check and, if necessary, tighten the
battery lead connections.CAUTION:ECB00620Never attempt to remove the battery cell seals,as this would permanently damage the battery.Recommended lubricant:
Lithium-soap-based grease
Recommended lubricant:
Lithium-soap-based grease
U3C261E0.book Page 45 Thursday, June 29, 2006 4:15 PM

KKey identification number ............................................. 11-1LLabel locations ............................................................... 2-1
Light switch .................................................................... 4-4MMain switch .................................................................... 4-1
Model label ................................................................... 11-2NNeutral indicator light ..................................................... 4-2OOn-Command four-wheel-drive switch ........................... 4-5
Owner’s manual and tool kit ........................................... 8-1PPark indicator light ......................................................... 4-3
Parking ........................................................................... 6-5
Parking on a slope ......................................................... 6-5
Part locations ................................................................. 3-1
Periodic maintenance and lubrication chart ................... 8-3
Pre-operation check list ................................................. 5-1RReverse indicator light ................................................... 4-2
Riding your ATV ............................................................. 7-1SSafety information .......................................................... 1-1
Seat .............................................................................. 4-12
Shock absorber assemblies, adjusting the front .......... 4-14
Shock absorber assembly, adjusting the rear .............. 4-15
Spark arrester, cleaning ............................................... 8-32
Spark plug, checking .................................................... 8-14
Specifications ............................................................... 10-1Speed limiter .................................................................. 4-6
Speedometer unit .......................................................... 4-3
Starter (choke) ............................................................. 4-11
Start switch .................................................................... 4-4
Steering shaft, lubricating ............................................ 8-45
Storage .......................................................................... 9-2
Storage compartment .................................................. 4-13
TTail/brake light bulb, replacing ..................................... 8-51
Throttle cable free play, adjusting ................................ 8-36
Throttle lever ........................................................... 4-6, 5-5
Tire pressure, measuring ............................................... 5-6
Tires ............................................................................... 5-5
Tire wear limit ................................................................ 5-7
Troubleshooting ........................................................... 8-54
Troubleshooting charts ................................................ 8-55VValve clearance ........................................................... 8-36
V-belt case drain plug .................................................. 8-34
V-belt cooling duct check hose .................................... 8-34
Vehicle identification number ....................................... 11-1WWheel bearings, checking ............................................ 8-45
Wheel, installing ........................................................... 8-53
Wheel, removing .......................................................... 8-52
U3C261E0.book Page 2 Thursday, June 29, 2006 4:15 PM