2007 YAMAHA VX CRUISER Owners Manual

Maintenance and care
74
CAUTION:
ECJ00190
If oil is leaking or the oil pressure warning
indicator comes on when the engine is
running, immediately shut the engine off
and have a Yamaha dealer check the wa-
tercraft. Continuing to operate the engine
under such conditions could cause severe
engine damage.
EJU34310Air filter element
Have a Yamaha dealer check and clean or re-
place the air filter element every 12 months or
every 100 hours of operation.
EJU34320Checking the jet thrust nozzle angle
Check the handlebars and jet thrust nozzle for
smooth operation.
Turn the handlebars as far as possible to the
right and left and check that the difference of
distances A and B between the jet thrust noz-
zle and the nozzle is within specification.
If the steering is stiff or misadjusted, have a
Yamaha dealer service it.
EJU34350Checking the shift cable (for VX
Deluxe/VX Cruiser)
Place the shift lever in the reverse position.
Make sure that the reverse gate makes con-
tact with the stopper.Difference of A and B:
Maximum 5 mm (0.20 in)
1Stopper
UF1K72E0.book Page 74 Wednesday, August 2, 2006 10:43 AM

Maintenance and care
75
If the reverse gate does not make contact with
the stopper, have a Yamaha dealer service it.
EJU34360Checking and adjusting the throttle
cable
Check that the throttle cable moves back to
the set position smoothly and that the throttle
lever free play is within specification.
(1) Squeeze and release the throttle lever. If
the throttle lever does not return smooth-
ly, have a Yamaha dealer service it.
(2) Adjust the free play by loosening the lock-
nut and turning the adjuster.
EJU34391Cleaning and adjusting the spark
plugs
The spark plug is an important engine compo-
nent and is easy to inspect. The condition of
the spark plug can indicate something about
the condition of the engine. For example, if
one spark plug has a distinctly different color,
the engine could require servicing. Do not at-
tempt to diagnose any problems yourself.
Have a Yamaha dealer service the watercraft.
Remove and inspect the spark plugs periodi-
cally; heat and deposits will cause the sparkplugs to slowly break down and erode. If elec-
trode erosion becomes excessive, or if carbon
and other deposits are excessive, replace the
spark plug with the specified plug.
To remove a spark plug:
(1) Remove the seat. (See page 26 for seat
removal and installation procedures.)
(2) Remove the spark plug cap.
CAUTION:
ECJ00210
Do not use any tools to remove or install
the spark plug cap, otherwise the ignition
coil coupler could be damaged. The spark
plug cap may be difficult to remove be-
cause the rubber seal on the end of the
cap fits tightly. To remove the spark plug
cap, simply twist it back and forth while
pulling it up; to install it, twist it back and
forth while pushing it down.
(3) Remove the spark plug.
Measure the spark plug gap with a wire
thickness gauge. Replace the spark plug
or adjust the gap to specification if neces-
sary.1Locknut
2Adjuster
3Throttle lever free play
Throttle lever free play:
4.0–7.0 mm (0.16–0.28 in)
Specified spark plug:
CR9EB
1Spark plug gap
Spark plug gap:
0.7–0.8 mm (0.028–0.031 in)
UF1K72E0.book Page 75 Wednesday, August 2, 2006 10:43 AM

Maintenance and care
76
To install a spark plug:
(1) Clean the gasket surface.
(2) Wipe any dirt from the threads of the
spark plug.
(3) Install the spark plug, and then tighten it
to the specified torque.
(4) Install the spark plug cap.
NOTE:

Wipe off any water on the spark plug or in-
side the spark plug cap before installing the
cap. Push the spark plug cap down until it is
securely installed.

If a torque wrench is not available when you
are installing a spark plug, a good estimate
of the correct torque is 1/4 turn to 1/2 turn
past finger tight using the spark plug
wrench included in the tool kit. Have the
spark plug adjusted to the correct torque
with a torque wrench as soon as possible.
WARNING
EWJ00350
Be careful not to damage the insulator
when removing or installing a spark plug.
A damaged insulator could allow sparks to
escape, which could result in a fire or ex-
plosion.
(5) Install the seat.EJU34421Lubrication points
To keep moving parts sliding or rotating
smoothly, coat them with water-resistant
grease.

Throttle cable (handlebar end)
Loosen the adjuster and disconnect the
outer cable from the bracket. Spray a rust
inhibitor into the outer cable. Connect the
outer cable, and then adjust the throttle ca-
ble free play. (See page 75 for adjustment
procedures.)

Steering cable (handlebar end)

Steering cable (jet thrust nozzle end)

Jet thrust nozzle pivot shaft Spark plug tightening torque:
12.5 Nm (9.2 ft-lb) (1.27 kgf-m)
Recommended water-resistant grease:
Yamaha Marine Grease/Yamaha
Grease A
1Adjuster
UF1K72E0.book Page 76 Wednesday, August 2, 2006 10:43 AM

Maintenance and care
77

For VX Deluxe/VX Cruiser:
Shift cable (reverse gate end)
EJU34450Checking the battery
Check the level of the battery electrolyte and
make sure that the negative (–) and positive
(+) battery leads are tightened securely.
WARNING
EWJ00790
Battery electrolyte is poisonous and dan-
gerous, causing severe burns, etc. Elec-
trolyte contains sulfuric acid. Avoid
contact with skin, eyes, or clothing.
Antidotes
External: Flush with water.
Internal: Drink large quantities of water or
milk. Follow with milk of magnesia, beaten
egg, or vegetable oil. Call a physician im-
mediately.
Eyes: Flush with water for 15 minutes and
get prompt medical attention.
Batteries produce explosive gases. Keep
sparks, flames, cigarettes, etc., well away.
If using or charging the battery in an en-
closed space, make sure that it is well ven-
tilated. Always shield your eyes when
working near batteries.
KEEP OUT OF THE REACH OF CHILDREN.
CAUTION:
ECJ00230

Be careful not to place the battery on its
side.

Be sure to remove the battery from the
battery compartment when adding elec-
trolyte or charging the battery.
To replenish the battery:
(1) Make sure that the electrolyte level is be-
tween the maximum and minimum level
marks.
(2) Refill the battery with distilled water if
necessary.
CAUTION:
ECJ00240
Normal tap water contains minerals that
are harmful to a battery. Use only distilled
water for replenishing the battery.
To recharge the battery:
CAUTION:
ECJ00250
Do not attempt to charge a battery hastily.
Battery life could be shortened.
It is recommended to have a Yamaha dealer
charge the battery. If you charge the battery
yourself, carefully read the battery charger in-
structions before charging and follow the
points below.
1Maximum level mark
2Minimum level mark
UF1K72E0.book Page 77 Wednesday, August 2, 2006 10:43 AM

Maintenance and care
78
(1) Remove all of the battery caps.
(2) If the electrolyte level is low, add distilled
water to raise it to the specified level.
(3) Set the charging rate to 1.9 ampere and
charge the battery slowly until the explo-
sive gases are discharged vigorously
from the battery cells.
To install the battery:
(1) Place the battery in the battery compart-
ment and connect the battery leads to the
battery terminals.
(2) Connect the breather hose to the battery.
(3) Secure the battery in place.
WARNING
EWJ00400
Be sure to connect the breather hose to
the battery. Fire or explosion could result
if the breather hose is damaged, obstruct-
ed, or not connected properly.
CAUTION:
ECJ00260
After installation, make sure that the bat-
tery leads are properly connected to the
battery terminals.
EJU34490Fuel injection system
The fuel injection system was set at the
Yamaha factory. If the fuel injection systemneeds to be adjusted, have a Yamaha dealer
service the watercraft.
CAUTION:
ECJ00220
Do not attempt to adjust the fuel injection
system. If the settings are disturbed by
someone who does not have the neces-
sary technical knowledge, poor engine
performance and damage may result.
EJU34500Checking the trolling speed
(1) Place the watercraft in the water.
(2) Start the engine and warm it up. Use the
tachometer in the multifunction informa-
tion center to check the trolling speed.
If the trolling speed is out of specification,
have a Yamaha dealer service the watercraft.
1Positive (+) battery terminal: Red lead
2Negative (–) battery terminal: Black lead
3Breather hose
Trolling speed:
1650 ±50 r/min
UF1K72E0.book Page 78 Wednesday, August 2, 2006 10:43 AM

Specifications
79
EJU34541
Specifications
Watercraft capacity:
Maximum people on board:
3 person
Maximum load capacity:
240 kg (530 lb)
Dimensions:
Length:
3220 mm (126.8 in)
Width:
1170 mm (46.1 in)
Height:
1150 mm (45.3 in)
Dry weight:
VX 319 kg (703 lb)
VX Deluxe 322 kg (710 lb)
VX Cruiser 323 kg (712 lb)
Performance:
Maximum output (according to ISO 8665/SAE
J1228):
75.0 kW@8000 r/min
Maximum fuel consumption:
28.0 L/h (7.4 US gal/h) (6.2 Imp.gal/h)
Cruising range at full throttle:
2.14 hour
Trolling speed:
1650 ±50 r/min
Engine:
Engine type:
Liquid cooled 4-stroke, DOHC
Number of cylinders:
4
Engine displacement:
1052 cm³
Bore & stroke:
76.0 × 58.0 mm (2.99 × 2.28 in)
Compression ratio:
11.4 :1
Valve clearance-intake (cold):
0.11–0.20 mm (0.0043–0.0079 in)
Valve clearance-exhaust (cold):
0.25–0.34 mm (0.0098–0.0134 in)
Lubrication system:
Dry sump
Cooling system:
Water
Starting system:
ElectricIgnition system:
T.C.I.
Spark plug:
CR9EB
Spark plug gap:
0.7–0.8 mm (0.028–0.031 in)
Battery capacity:
12 V, 19.0 Ah
Charging system:
Flywheel magneto
Drive unit:
Propulsion system:
Jet pump
Jet pump type:
Axial flow, single stage
Impeller rotation:
Counterclockwise
Jet thrust nozzle angle:
24.0+24.0 °
Fuel and oil:
Recommended fuel:
Regular unleaded gasoline
Minimum octane rating (PON):
86
Minimum octane rating (RON):
90
Recommended oil:
SAE 10W-30, 20W-40, 20W-50
Oil grade:
API SE,SF,SG,SH,SJ,SL
Fuel tank total capacity:
60 L (15.9 US gal) (13.2 Imp.gal)
Engine oil quantity with oil filter replacement:
2.2 L (2.33 US qt) (1.94 Imp.qt)
Engine oil quantity without oil filter replacement:
2.0 L (2.11 US qt) (1.76 Imp.qt)
Engine oil total quantity:
4.3 L (4.55 US qt) (3.78 Imp.qt)
UF1K72E0.book Page 79 Wednesday, August 2, 2006 10:43 AM

Trouble recovery
80
EJU34560
Troubleshooting
If you have any trouble with your watercraft, use this section to check for the possible cause.
If you cannot find the cause, or if the procedure for replacement or repair is not described in
this owner’s/operator’s manual, have a Yamaha dealer perform the necessary service.
EJU34591Troubleshooting chart
TROUBLE POSSIBLE CAUSE REMEDY PAGE
Engine does not
start (Starter motor
does not turn over)Yamaha Se-
curity Sys-
tem (VX
Deluxe/VX
Cruiser)Lock mode selected Select unlock mode
32
Engine shut-
off switchClip not in place Install clip
28
Fuse Burned out Replace the fuse and
check wiring84
Battery Run down Recharge 77
Poor terminal con-
nectionsTighten as required
77
Terminal corroded Clean 68
Starter motor Faulty Have serviced by
Yamaha dealer—
Engine does not
start (Starter motor
turns over)Throttle lever Squeezed Release 29
Fuel Empty Refill as soon as pos-
sible42
Stale or contaminat-
edHave serviced by
Yamaha dealer73
Fuel tank Water or dirt present Have serviced by
Yamaha dealer73
Spark plug Fouled or defective Clean or replace 75
Spark plug
capNot connected or
looseConnect properly
75
Connected to wrong
cylinderConnect properly
75
Fuel injec-
tion systemFuel pump faulty Have serviced by
Yamaha dealer—
UF1K72E0.book Page 80 Wednesday, August 2, 2006 10:43 AM

Trouble recovery
81
Engine runs irregu-
larly or stallsFuel Empty Refill as soon as pos-
sible42
Stale or contaminat-
edHave serviced by
Yamaha dealer73
Fuel tank Water or dirt present Have serviced by
Yamaha dealer73
Spark plug Fouled or defective Replace 75
Incorrect heat range Replace 75
Gap incorrect Adjust 75
Spark plug
capLoose Connect properly 75
Cracked, torn, or
damagedReplace
—
Electrical wir-
ingLoose connection Tighten or connect
properly—
Fuel injec-
tion systemFaulty or clogged in-
jectorsHave serviced by
Yamaha dealer—
Warning light or in-
dicator blinksFuel level Empty Refill as soon as pos-
sible42
Engine over-
heatedJet intake clogged Clean
82
Check engine
warningFaulty sensors Have serviced by
Yamaha dealer37
Watercraft slow or
loses powerYamaha Se-
curity Sys-
tem (VX
Deluxe/VX
Cruiser)Low-RPM mode se-
lectedSelect normal mode
33
Cavitation Jet intake clogged Clean 82
Impeller damaged or
wornHave serviced by
Yamaha dealer82
Engine over-
heat warningEngine speed reduc-
tion control activatedClean jet intake and
cool engine36
Oil pressure
warningEngine speed reduc-
tion control activatedAdd oil
35
Spark plug Fouled or defective Replace 75
Incorrect heat range Replace 75
Gap incorrect Adjust 75
Spark plug
capsLoose Connect properly
75
Electrical wir-
ingLoose connection Tighten or connect
properly—
Fuel Stale or contaminat-
edHave serviced by
Yamaha dealer73
Air filter Clogged or oil buildup Have serviced by
Yamaha dealer74 TROUBLE POSSIBLE CAUSE REMEDY PAGE
UF1K72E0.book Page 81 Wednesday, August 2, 2006 10:43 AM