ONLY FOR CANADA
GENERAL MAINTENANCE AND LUBRICATION CHART
NOTE:
From 18 months or 7,000 km (4,200 mi) or 210 hours, repeat the maintenance intervals starting from 6 months
or 3,000 km (1,800 mi) or 90 hours.
Items marked with an asterisk should be performed by a Yamaha dealer as they require special tools, data and
technical skills.
For TT-Rs not equipped with an odometer or an hour meter, follow the month maintenance intervals.
For TT-Rs equipped with an odometer or an hour meter, follow the km (mi) or hours maintenance intervals.
Hovewer, keep in mind that if the TT-R isn´t used for a long period of time, the month maintenance intervals
should be followed.
INSP
ADJ
MAINTENANCE INTERVALS
3 - 0 - 2
Nº ITEM CHECKS AND MAINTENANCE JOBS
ODOMETER READINGSINITIAL
ClutchCheck operation
Adjust or replace cable. 1
*
Whichever
comer firstmonth
km
(mi)
hours1,000
(600)1612
3,000
(1,800)5,000
(3,000)
30 90 150
Spark arresterClean.
Front brake(TT-R125 / TT-R125E)
Check operation.
Adjust brake lever free play and replace brake shoes if necessary.
(TT-R125LW / TT-R215LWE)
Check operation, fluid level, and for fluid leakage.
Replace brake pads if necessary.
Replace brake fluid every 1 year. (TT-R125LW / TT-R125LWE)
Rear brakeCheck operation.
Adjust brake pedal free play and replace brake shoes if necessary
Brake hose
(TT-R125LW / TT-
R125LWE)Check for clack damage.
Replace
WheelsCheck runout, spoke tightness and for damage.
Tighten spokes if necessary.
TiresCheck tread depth and for damage.
Replace if necessary.
Check air pressure.
Correct if necessary.
Wheel bearingsCheck bearings for smooth operation.
Replace if necessary.
SwingarmCheck swingarm pivoting point for play.
Correct if necessary.
Lubricate with lithium soap based grease.
Drive chainCheck chain slack / alignment and condition.
Adjust and lubricate chain.
Steering
bearingsCheck bearing assemblies for looseness.
Lubricate with litium soap based grease every 4,000 km (2,400 mi) or
120 hours or 12 months (whichever comes first).
Brake and clutch
lever pivot shaftsApply lithium soap based grease lightly.
2
*3
*4
*5
*6
*7
*8
*9
10
11*
12
Brake pedal pivot
shaftsApply lithium soap based grease lightly.
Sidestand pivotCheck operation.
Apply lithium soap based grease lightly. 1314
Front forkCheck operation and for oil leakage.
Replace if necessary.
15*
Every 1 year
Every 4 year
Every ride
√√√
√
√√√
√√√
√√
√√√
√√
√√
√√√
√√
√√√
√√√
√√
√√
3 - 3
INSP
ADJ
PRE-OPERATION INSPECTION AND MAINTENANCE
PRE-OPERATION INSPECTION AND MAINTENANCE
Before riding for break-in operation or practice, make sure the machine is in good operating condi-
tion.
Before using this machine, check the following points.
GENERAL INSPECTION AND MAINTENANCE
Item Routine Page
FuelCheck that a fresh gasoline is filled in the fuel tank. Check the
fuel line for leakage.P.1-12
Engine oilCheck that the oil level is correct. Check the crankcase for leak-
age.P.3-7 ~ 10
Gear shifter and clutchCheck that gears can be shifted correctly in order and that the
clutch operates smoothly.P.3-4
Throttle grip/housingCheck that the throttle grip operation and free play are correctly
adjusted. Lubricate the throttle grip and housing, if necessary.P.3-4 ~ 5
BrakesCheck the play of front and rear brake and effect of front and
rear brake.
Check fluid level and leakage. (TT-R125LW/TT-R125LWE only)P.3-15 ~ 20
Drive chainCheck chain slack and alignment. Check that the chain is lubri-
cated properly.P.3-21 ~ 22
WheelsCheck for excessive wear and tire pressure. Check for loose
spokes and have no excessive play.P.3-27 ~ 28
SteeringCheck that the handlebar can be turned smoothly and have no
excessive play.P.3-28 ~ 32
Front forks and rear shock
absorber assemblyCheck that they operate smoothly and there is no oil leakage. P.3-23 ~ 26
Cables (wires)Check that the clutch and throttle cables move smoothly. Check
that they are not caught when the handlebars are turned or
when the front forks travel up and down.—
Muffler Check that the muffler is tightly mounted and has no cracks. P.4-2
Sprocket Check that the driven sprocket tightening nut is not loose. P.3-20
Lubrication Check for smooth operation. Lubricate if necessary. P.3-33
Bolts and nuts Check the chassis and engine for loose bolts and nuts.—
Lead connectorsCheck that the CDI magneto, CDI unit, and ignition coil are con-
nected tightly.P.1-5
