2007 YAMAHA SUPERJET fuel cap

Maintenance and care
46
EJU33480
Storage
WARNING
EWJ00320
Always turn the fuel cock knob to “OFF”
when storing the watercraft, otherwise
fuel could leak out into the engine or en-
gine compartment, which would create a
fire hazard.
Storage for long periods of time, such as win-
ter storage, requires preventive maintenance
to ensure against deterioration. It is advisable
to have the watercraft serviced by a Yamaha
dealer prior to storage. However, the following
procedures can be performed by the owner.
EJU33510Flushing the cooling system
Flushing the cooling system is essential to
prevent it from clogging with salt, sand, or dirt.
CAUTION:
ECJ00120

Do not supply water to the cooling water
passages when the engine is not run-
ning. The water could flow back through
the muffler into the crankcase, causing
severe engine damage.

Do not run the engine for more than 15
seconds on land without supplying wa-
ter, otherwise the engine could over-
heat.
(1) Remove the watercraft from the water
and place it in a horizontal position.
(2) Remove the flushing hose connector
cap, and then insert the garden hose
adapter into the flushing hose connector
and turn it until it is securely connected.
(3) Connect the garden hose adapter to a
water tap using a garden hose.
NOTE:
A garden hose is not included and must be
purchased separately.
(4) Start the engine, and then immediately
turn the water supply on until water flows
out continually from the cooling water pi-
lot outlet.
(5) Run the engine at idling speed for about
3 minutes watching the engine condition.
If the engine stops while flushing, turn the
water supply off immediately and repeat
the above steps.
(6) Turn the water supply off, and then force
the remaining water out of the cooling
water passages by alternately squeezing
and releasing the throttle lever for 10 to
15 seconds.
(7) Stop the engine.
1Garden hose adapter
2Flushing hose connector
3Flushing hose connector cap
UF1N75E0.book Page 46 Tuesday, May 16, 2006 9:53 AM

Maintenance and care
47
(8) Remove the garden hose adapter and in-
stall the flushing hose connector cap.
EJU33560Lubrication
WARNING
EWJ00300
To reduce the risk of fire or explosion:
Never pour or spray gasoline, or any sub-
stance other than a rust inhibitor through
the hole in the carburetor silencer cover.
CAUTION:
ECJ00150

Be sure to install the silencer cap se-
curely after fogging the engine, other-
wise water could enter the engine and
cause damage.

Do not run the engine for more than 15
seconds on land, otherwise the engine
could overheat.
(1) Remove the silencer cap.
(2) Start the engine with the watercraft in a
well-ventilated area.
(3) With the engine running at a fast idle,
quickly spray as much rust inhibitor as
possible through the hole in the silencer
cover. Keep spraying until the engine
stalls (or a maximum of 15 seconds).
(4) Install the silencer cap securely.
(5) Lubricate all cables such as the throttle,
choke, and steering cables.
NOTE:
Use a suitable marine grease applicator to
pressure-lubricate the cables and purge out
any moisture between the inner and outer ca-
bles.
(6) Lubricate the areas of the watercraft
specified in “Lubrication points” on page
57.
EJU33640Fuel system
WARNING
EWJ00290
GASOLINE AND ITS VAPORS ARE HIGH-
LY FLAMMABLE AND EXPLOSIVE!

Do not smoke when refueling, and keep
away from sparks, flames, and other
sources of ignition.

Stop the engine before refueling.

Refuel in a well-ventilated area with the
watercraft in a horizontal position.

Do not stand or sit on the watercraft
while refueling in case of fire.

Take care not to spill gasoline. If gaso-
line spills, wipe it up immediately with
dry rags. Always properly dispose of
gasoline-soaked rags.

Avoid overfilling the fuel tank. Stop fill-
ing when the fuel level just reaches the
bottom of the filler tube. Do not fill up the
filler tube because fuel expands as it
warms up and could overflow. If tempo-
rarily leaving the watercraft with a full
fuel tank, do not leave it in direct sun-
light. Leave it in a well-ventilated area
with the watercraft in a horizontal posi-
tion.

Tighten the fuel tank filler cap securely
after refueling.

If you should swallow some gasoline, in-
hale a lot of gasoline vapor, or get gaso-
1Silencer cap
UF1N75E0.book Page 47 Tuesday, May 16, 2006 9:53 AM

Maintenance and care
52
EJU34200Checking the fuel system
WARNING
EWJ00370
Gasoline is highly flammable and explo-
sive. Failure to check for and repair any
fuel leakage could result in a fire or explo-
sion. A fire or explosion can cause severe
injury or death. Shut the engine off. Do not
smoke. Avoid spilling gasoline.
Check the fuel system for leaks, cracks, and
malfunctions. If any problem is found, do the
necessary repair or replacement as required.
If repair is necessary, consult a Yamaha deal-
er.
Check:

Carburetor for leakage.

Fuel pump for malfunction and leakage.

Fuel tank filler cap and seal for damage.

Fuel in fuel tank for water and dirt.

Fuel tank for damage, cracks, and leakage.

Fuel hoses and joints for damage, cracks,
and leakage.

Fuel filter for leakage.

Fuel cock for leakage.

Air vent check valve for leakage.EJU34220Fuel filter
This watercraft is equipped with a one-piece,
disposable fuel filter. The fuel filter should be
replaced after the initial 10 hours or first
month of operation and every 200 hours or 24
months thereafter, or if water is found in the fil-ter. Have a Yamaha dealer replace the fuel fil-
ter if necessary.
WARNING
EWJ00360
Do not try to replace the fuel filter yourself.
An incorrectly installed filter can leak gas-
oline, which could result in a fire or explo-
sion. If necessary, have a Yamaha dealer
replace the fuel filter.
EJU34230Fuel tank
Check the fuel tank for leakage and for water
in the tank. If water is found in the fuel system,
or if the fuel tank needs to be cleaned, have a
Yamaha dealer service the watercraft.
EJU34320Checking the jet thrust nozzle angle
Check the handlebars and jet thrust nozzle for
smooth operation.
1Fuel filter
1Fuel tank
UF1N75E0.book Page 52 Tuesday, May 16, 2006 9:53 AM

Specifications
61
EJU34540
Specifications
Watercraft capacity:
Maximum people on board:
1 person
Dimensions:
Length:
2240 mm (88.2 in)
Width:
680 mm (26.8 in)
Height:
660 mm (26.0 in)
Dry weight:
132.0 kg (291 lb)
Performance:
Maximum output (according to ISO 8665/SAE
J1228):
48.5 kW@6250 r/min
Maximum fuel consumption:
29.0 L/h (7.7 US gal/h) (6.4 Imp.gal/h)
Crusing range at full throttle:
0.62 hour
Trolling speed:
1300 ±50 r/min
Engine:
Engine type:
2-stroke
Number of cylinders:
2
Engine displacement:
701.0 cm³ (42.78 cu.in)
Bore & stroke:
81.0 × 68.0 mm (3.19 × 2.68 in)
Compression ratio:
7.20 :1
Lubrication system:
Pre-mixed fuel and oil
Cooling system:
Water
Starting system:
Electric
Ignition system:
C.D.I.
Spark plug:
BR7HS
Spark plug gap:
0.6–0.7 mm (0.024–0.028 in)
Battery capacity:
12 V19.0 AhCharging system:
Flywheel magneto
Drive unit:
Propulsion system:
Jet pump
Jet pump type:
Axial flow, single stage
Impeller rotation:
Counter clockwise
Jet thrust nozzle angle:
18.5, 20.5, 22.5, 24.5
Fuel and oil:
Recommended fuel:
Regular unleaded gasoline
Minimum octane rating (PON):
86
Minimum octane rating (RON):
90
Recommended engine oil:
YAMALUBE 2-W or TC-W3 outboard motor
oil or equivalent
Fuel mixing ratio (fuel to oil):
50 :1
Fuel tank total capacity:
18.0 L (4.8 US gal) (4.0 Imp.gal)
Fuel tank reserve capacity:
5.5 L (1.5 US gal) (1.2 Imp.gal)
UF1N75E0.book Page 61 Tuesday, May 16, 2006 9:53 AM

Trouble recovery
62
EJU34560
Troubleshooting
If you have any trouble with your watercraft, use this section to check for the possible cause.
If you cannot find the cause, or if the procedure for replacement or repair is not described in
this owner’s/operator’s manual, have a Yamaha dealer perform the necessary service.
EJU34570Troubleshooting chart
TROUBLE POSSIBLE CAUSE REMEDY PAGE
Engine does not
start (Starter motor
does not turn over)Engine shut-
off switchClip not in place Install clip
20
Fuse Burned out Replace fuse and
check wiring66
Battery Run down Recharge 59
Poor terminal con-
nectionsTighten as required
59
Terminal corroded Clean 48
Starter motor Faulty Have serviced by
Yamaha dealer—
Engine does not
start (Starter motor
turns over)Fuel cock Turned to “OFF”Turn fuel cock knob to
“ON”19
Fuel Empty Refill as soon as pos-
sible26
Stale or contaminat-
edHave serviced by
Yamaha dealer52
Fuel tank Water or dirt present Have serviced by
Yamaha dealer52
Spark plug Fouled or defective Clean or replace 56
Spark plug
capNot connected or
looseConnect properly
56
Crankcase Filled with water Crank engine with
plug out until clean67
Fuel filter Clogged or water
pooledHave serviced by
Yamaha dealer52
Choke Knob moves back on
its ownTighten choke knob
adjusting nut58
UF1N75E0.book Page 62 Tuesday, May 16, 2006 9:53 AM

Trouble recovery
63
Engine runs irregu-
larly or stallsFuel Empty Refill as soon as pos-
sible26
Stale or contaminat-
edHave serviced by
Yamaha dealer52
Too much oil in fuel
mixing ratioCorrect fuel-to-oil ra-
tio to 50:125
Choke Knob is left pulled Push fully in 20
Fuel filter Clogged or water
pooledHave serviced by
Yamaha dealer52
Fuel tank Water or dirt present Have serviced by
Yamaha dealer52
Spark plug Fouled or defective Replace 56
Incorrect heat range Replace 56
Gap incorrect Adjust 56
Spark plug
capLoose Connect properly 56
Cracked, torn or dam-
agedReplace
—
Electrical wir-
ingLoose electrical con-
nectionsTighten or connect
properly—
Carburetor Incorrect idle adjust-
mentAdjust idle
60
Clogged Have serviced by
Yamaha dealer60
Watercraft slow or
loses powerCavitation Jet intake clogged Clean 64
Impeller damaged or
wornHave serviced by
Yamaha dealer64
Engine over-
heatedJet intake clogged Clean
64
Fuel filter Clogged Have serviced by
Yamaha dealer52
Spark plug Fouled or defective Replace 56
Incorrect heat range Replace 56
Gap incorrect Adjust 56
Spark plug
capsLoose Connect properly
56
Fuel Stale or contaminat-
edHave serviced by
Yamaha dealer52 TROUBLE POSSIBLE CAUSE REMEDY PAGE
UF1N75E0.book Page 63 Tuesday, May 16, 2006 9:53 AM

Trouble recovery
67

The bow must be kept up out of the wa-
ter during towing to prevent water from
entering the engine compartment.
WARNING
EWJ00810

The watercraft should only be towed in
an emergency.

The towline should be long enough so
that the watercraft will not collide with
the towing boat when slowing down. A
good rule of thumb is a towline that is
three times the combined length of the
towing boat and the watercraft.

The operator of the towing boat must
keep speed to a minimum and avoid traf-
fic or obstacles which could be a hazard
to the rider on the watercraft.
EJU34730Submerged watercraft
If the watercraft is submerged or flooded with
water, follow the procedure below and consult
a Yamaha dealer as soon as possible. Failure
to do so could result in serious engine dam-
age!
In an emergency:
(1) Beach the watercraft and remove the
hood. Turn the watercraft over far enough
to drain the water from the engine com-
partment.
CAUTION:
ECJ00700
Turning the watercraft on its side with the
hood removed could cause damage to the
steering pole. Use two people to provide
enough support to make sure that the
steering pole is not damaged.
(2) Turn the watercraft upright again.
(3) Turn the fuel cock knob to “OFF”.
(4) Remove the spark plugs and dry them
with a cloth.
(5) Without reinstalling the spark plugs,
crank the engine until all of the water in
the cylinders has been drained.
(6) Install the spark plugs and the hood.
(7) Turn the fuel cock knob to “ON”.
(8) Launch the watercraft into the water, and
then run the engine for at least 10 min-
utes. If the engine does not start, repeat
steps 3–8.
(9) Shut the engine off.
(10) Turn the fuel cock knob to “OFF”, remove
the silencer cap, and then spray a rust in-
hibitor into the carburetor while cranking
the engine.
(11) Have the watercraft inspected by a
Yamaha dealer as soon as possible.
1Bow rope hole
UF1N75E0.book Page 67 Tuesday, May 16, 2006 9:53 AM

Index
2-stroke engine oil .................................... 25
B
Battery ................................................ 29, 48
Battery, checking...................................... 59
Battery, jumping ....................................... 65
Beaching the watercraft ........................... 43
Bilge ......................................................... 29
Boarding and starting in deep water ........ 39
Boarding and starting in shallow water .... 39
Bow rope hole .......................................... 22
Builder’s plate............................................. 2
C
Capsized watercraft ................................. 40
Carburetor, adjusting................................ 60
Choke cable, adjusting ............................. 58
Choke knob .............................................. 20
Cleaning the watercraft ............................ 48
Cooling water pilot outlet .................... 21, 32
Cruising limitations ..................................... 9
E
Emergency procedures ............................ 64
Engine break-in ........................................ 33
Engine compartment ................................ 28
Engine overheat warning system ............. 23
Engine serial number ................................. 1
Engine shut-off cord ................................. 31
Engine shut-off switch .............................. 20
Engine stop switch ................................... 20
Enjoy your watercraft responsibly ............ 15
F
Filling the fuel tank ................................... 26
Fire extinguisher....................................... 29
Flushing the cooling system ..................... 46
Fuel and oil............................................... 25
Fuel cock knob ......................................... 19
Fuel filter .................................................. 52
Fuel system ........................................ 28, 47
Fuel system, checking.............................. 52
Fuel tank .................................................. 52
Fuel tank filler cap .................................... 19
Fuse, replacing......................................... 66
G
Gasohol .................................................... 25
Gasoline ................................................... 25Getting to know your watercraft ............... 36
H
Hazard information ................................... 13
Hood ......................................................... 18
Hull and deck ........................................... 28
Hull Identification Number (HIN)................. 1
I
Identification numbers ................................ 1
Important labels .......................................... 3
J
Jet intake .................................................. 31
Jet intake and impeller, cleaning .............. 64
Jet thrust nozzle angle, adjusting ............. 53
Jet thrust nozzle angle, checking ............. 52
Jumper cables, connecting ...................... 65
K
Kneeling ................................................... 37
L
Labels, other .............................................. 7
Labels, warning .......................................... 4
Launching the watercraft .......................... 33
Learning to operate your watercraft ......... 36
Leaving the watercraft .............................. 36
Limitations on who may operate the
watercraft ................................................ 8
Lubrication................................................ 47
Lubrication points ..................................... 57
M
Main components, location of .................. 16
Maintenance and adjustments ................. 49
Mixing fuel and oil .................................... 25
Model information....................................... 2
O
Operating positions .................................. 37
Operating your watercraft ......................... 36
Operation ................................................. 33
Operation of controls and other
functions ............................................... 18
Operation requirements ........................... 10
Owner’s/operator’s manual and tool kit .... 49
P
Periodic maintenance chart ...................... 51
Post-operation care .................................. 44
Pre-operation check list ............................ 27
Pre-operation check points ...................... 28
UF1N75E0.book Page 1 Tuesday, May 16, 2006 9:53 AM