2007 YAMAHA RHINO 660 drain bolt

8-8
Fuel line*Check fuel hose for cracks or damage.
Replace if necessary.Engine oilReplace (warm engine before draining).Engine oil filter cartridgeReplace.Final gear oil
Check oil level/oil leakage.
Replace.Differential gear oil
Front brake*Check operation/brake pad wear/fluid leakage/see NOTE page
8-9.
Correct if necessary. Replace pads if worn to the limit.Rear brake*Check operation/brake pad wear/fluid leakage/see NOTE page
8-9.
Correct if necessary. Replace pads if worn to the limit.Accelerator pedal*Check operation and free play.V-belt*Check operation.
Check for wear, cracks, or damage.Wheels*Check balance/damage/runout.
Repair if necessary.Wheel bearings*Check bearing assemblies for looseness/damage.
Replace if damaged.Front and rear
suspension*Check operation and for leakage.
Correct if necessary.Steering system*Check operation and for looseness/Replace if damaged.
Check toe-in/Adjust if necessary.Rear upper and lower
knuckle pivots*Lubricate with lithium-soap-based grease.Drive shaft universal joint*Lubricate with lithium-soap-based grease.Engine mount*Check for cracks or damage.
Check bolt tightness.Front and rear axle boots*Check operation.
Replace if damaged.Stabilizer bushings*Check for cracks or damage.
ITEM ROUTINEWhichever
comes firstINITIAL EVERY
month136612
km
(mi)320
(200)1,200
(750)2,400
(1,500)2,400
(1,500)4,800
(3,000)
hours 20 75 150 150 300
EE.book Page 8 Friday, August 4, 2006 12:02 PM

8-27 1. Engine oil drain bolt
1. Vis de vidange d’huile moteur
1. Perno de vaciado del aceite del motor
1. Oil filter cartridge 2. Oil filter wrench
1. Cartouche de filtre à huile 2. Clé pour filtre à huile
1. Cartucho del filtro de aceite 2. Llave para filtros de aceite
To change the engine oil (with or without oil fil-
ter cartridge replacement)
1. Remove the console. (See page 8-21 for
console removal and installation proce-
dures.)
2. Place an oil pan under the engine to collect
the used oil, and then remove the engine oil
filler cap.
3. Remove the engine oil drain bolt to drain the
oil from the crankcase.NOTE:_ Skip steps 4–6 if the oil filter cartridge is not being
replaced. _4. Remove the oil filter cartridge with an oil filter
wrench.NOTE:_ An oil filter wrench is available at a nearby
Yamaha dealer. _
EE.book Page 27 Friday, August 4, 2006 12:02 PM

8-29 1. O-ring
1. Joint torique
1. Junta tórica
1. Oil filter cartridge 2. Torque wrench
1. Cartouche de filtre à huile 2. Clé dynamométrique
1. Cartucho del filtro de aceite 2. Llave dinamométrica
5. Apply a light coat of engine oil to the O-ring of
the new oil filter cartridge.NOTE:_ Make sure the O-ring is seated properly. _6. Install the new oil filter cartridge with an oil fil-
ter wrench, and then tighten it to the specified
torque with a torque wrench.
7. Install the engine oil drain bolt, and then tight-
en it to the specified torque.
8. Add the specified amount of recommended
engine oil, and then install the engine oil filler
cap and tighten it. Tightening torque:
Oil filter cartridge:
17 Nm (1.7 m·kgf, 12 ft·lbf)
Tightening torque:
Engine oil drain bolt:
30 Nm (3.0 m·kgf, 22 ft·lbf)
EE.book Page 29 Friday, August 4, 2006 12:02 PM

8-37 1. Final gear oil drain bolt
1. Vis de vidange d’huile de couple conique arrière
1. Perno de vaciado de aceite del engranaje final
Changing the final gear oil
1. Place the vehicle on a level surface.
2. Place a container under the final gear case to
collect the used oil.
3. Remove the oil filler bolt and the drain bolt to
drain the oil.
4. Install the drain bolt, and then tighten it to the
specified torque.
5. Add the recommended final gear oil up to the
brim of the filler hole. Tightening torque:
Final gear oil drain bolt:
20 Nm (2.0 m·kgf, 14 ft·lbf)
Recommended oil:
SAE 80 API GL-4 Hypoid gear oil
Oil quantity:
0.25 L (0.22 Imp qt, 0.26 US qt)
EE.book Page 37 Friday, August 4, 2006 12:02 PM

8-43 1. Differential gear oil drain bolt
1. Vis de vidange de l’huile de différentiel
1. Perno de vaciado de aceite del diferencial
Changing the differential gear oil
1. Place the vehicle on a level surface.
2. Place a container under the differential gear
case to collect the used oil.
3. Remove the differential gear oil filler bolt and
differential gear oil drain bolt to drain the oil.
4. Install the differential gear oil drain bolt, and
tighten it to the specified torque.
5. Fill the differential gear case with the recom-
mended oil. Tightening torque:
Differential gear oil drain bolt:
9.8 Nm (0.98 m·kgf, 7.1 ft·lbf)
Recommended oil:
SAE 80 API GL-5 Hypoid gear oil
Oil quantity:
0.32 L (0.28 Imp qt, 0.34 US qt)
EE.book Page 43 Friday, August 4, 2006 12:02 PM

9-7
EVU01561
B. STORAGE
Long term storage (60 days or more) of your vehi-
cle will require some preventive procedures to
guard against deterioration. After thoroughly
cleaning the vehicle, prepare for storage as fol-
lows:
1. Fill the fuel tank with fresh fuel and add fuel
stabilizer (if available). Operate the vehicle
for at least 5 minutes to distribute treated fuel
through the fuel system.
2. Drain the fuel from the carburetor float cham-
ber into a clean container by loosening the
drain bolt; this will help prevent fuel deposits
from building up. Pour the drained fuel into
the fuel tank.NOTE:_ Use of fuel stabilizer eliminates the need to drain
the fuel system. Consult a Yamaha dealer if the
fuel system is to be drained instead. _
EE.book Page 7 Friday, August 4, 2006 12:02 PM