1
2
3
4
5
6
7
8
9
10
INSTRUMENT AND CONTROL FUNCTIONS
3-5
The electrical circuit of the warning
light can be checked by turning the
key to “ON”.
If the warning light does not come on
for a few seconds, and then go off,
have a Yamaha dealer check the elec-
trical circuit.
NOTE:
This model is also equipped with a
self-diagnosis device for the fuel level
detection circuit. If the fuel level detec-
tion circuit is defective, the following
cycle will be repeated until the mal-
function is corrected: The fuel level
warning light will flash eight times, and
then go off for 3.0 seconds. If this oc-
curs, have a Yamaha dealer check the
vehicle.
EAUB1392
Multi-function meter unit
1. Speedometer
2. Tachometer
3. Clock
4. Odometer/Tripmeters/Fuel reserve tripmeter
5. “SELECT” button
6. “RESET” button
EWA12421
WARNING0
Be sure to stop the vehicle before
making any setting changes to the
multi-function meter unit.
The multi-function meter unit is equip-
ped with the following:
a speedometer (which shows the
riding speed)
a tachometer (which shows en-
gine speed)
an odometer (which shows the to-
tal distance traveled)
two tripmeters (which show the
distance traveled since they were
last set to zero)
a fuel reserve tripmeter (which
shows the distance traveled since
the fuel level warning light came on)
a clock
a self-diagnosis device
an indicator lights brightness con-
trol mode
To switch the speedometer and
odometer/tripmeter displays between
kilometers and miles, push the “SE-
LECT” and “RESET” buttons together
and turn the key to “ON”. When the
digits start flashing on the display,
push the “SELECT” button to choose
kilometers or miles.
NOTE:
Be sure to turn the key to “ON” before
using the “SELECT” and “RESET”
buttons.
MY03 01-03 ING 6-10-2005 13:52 Pagina 3-5
1
2
3
4
5
6
7
8
9
10
INSTRUMENT AND CONTROL FUNCTIONS
3-7
Clock mode
1. Clock
2. “SELECT” button
3. “RESET” button
Turn the key to “ON”.
T
o set the clock
1. Push the “SELECT” button for at
least two seconds.
2. When the hour digits start flash-
ing, push the “RESET” button to
set the hours.
3. Push the “SELECT” button, and
the minute digits will start flash-
ing.
4. Push the “RESET” button to set
the minutes.
5. Push the “SELECT” button, and
then release it to start the clock.
Self-diagnosis devices
1. Engine trouble warning light “U”
2. Immobilizer system indicator light “ ”
This model is equipped with a self-diag-
nosis device for various electrical cir-
cuits. If any of those circuits are defec-
tive, the engine trouble warning light
will start flashing. If this occurs, have a
Yamaha dealer check the vehicle.
This model is also equipped with a
self-diagnosis device for the immobi-
lizer system.
Turn the key to "ON". If any of the im-
mobilizer system circuits are defec-
tive, the immobilizer system indicator
light will flash, and it will indicate an er-
ror code.
If this occurs, have a Yamaha dealer
check the vehicle. However, if the indi-
cator light slowly flashes five times,
and then quickly flashes two times re-
peatedly, this error could be caused by
signal interference. If this occurs, try
the following.
1. Use the code re-registering key to
start the engine.
NOTE:
Make sure there are no other immobi-
lizer keys close to the main switch,
and do not keep more than one immo-
bilizer key on the same key ring! Im-
mobilizer system keys may cause sig-
nal interference, which may prevent
the engine from starting.
2. If the engine starts, turn it off and
try starting the engine with the
standard keys.
3. If one or both of the standard keys
do not start the engine, take the
vehicle, the code re-registering
key and both standard keys to a
Yamaha dealer and have the
standard keys re-registered.
MY03 01-03 ING 6-10-2005 13:52 Pagina 3-7
