2007 YAMAHA JOG50R high beam

EAU10430
Controls and instruments
DESCRIPTION
2-3
2
17. Rear brake lever (page 6-11)
18. Left handlebar switch (page 3-3)
19. Speedometer (page 3-2)
20. Turn signal indicator light (page 3-1)
21. High beam light (page 3-1)
22. Oil level warning light (page 3-1)
23. Coolant temperature warning light (page 3-1)
24. "TRIP" button (page 3-2)25. Fuel gauge (page 3-3)
26. Front brake lever (page 3-4 )
27. Right handlebar switch (page 3-3)
28. Turn signal switch (page 3-3)
29. Horn switch (page 3-3)
30. Main switch (page 3-1)
31. Coolant level gauge window (page 6-7)
kb
ajd
z
c4050
30
10 2060
70
80
0
y
17
2928
31 30 2726
20 21
25 23 19 20
18
2422
5RW-F8199-E3.qxd 08/09/2005 18:07 Página 14

EAU10460
Main switch/steering lock
The main switch/steering lock con-
trols the ignition and lighting systems,
and is used to lock the steering. The
various positions are described
below.
EAU10630
ON
All electrical systems are supplied
with power, and the engine can be
started. The key cannot be removed.
EAU10660
OFF
All electrical systems are off. The key
can be removed.
EAU10670
*
The 2-stroke engine oil level warning
light should come on. (See page 3-1.)
EAU10680
LOCK
The steering is locked, and all electri-
cal systems are off. The key can be
removed.
T
o lock the steering
1. Turn the handlebars all the way to
the left.
2. Push the key in from the “OFF”
position, and then turn it to
“LOCK” while still pushing it.
3. Remove the key.
T
o unlock the steering
Push the key in, and then turn it to
“OFF” while still pushing it.
EWA10060
s s
WARNING
Never turn the key to “OFF” or
“LOCK” while the vehicle is
moving, otherwise the electrical
systems will be switched off, which
may result in loss of control or an
accident. Make sure that the vehi-
cle is stopped before turning the
key to “OFF” or “LOCK”.
EAU10980
Indicator lights
1. Turn signal indicator lights “b”
2. High beam indicator light “j”
3. Oil level warning light “z”
4. Coolant temperature warning light “y”
j
d
z
c4050
30
10 2060
70
80
0
y
00000.0
23:08TOTALExF
3
INSTRUMENT AND CONTROL FUNCTIONS
3-1
2 1
4
3
1
5RW-F8199-E3.qxd 08/09/2005 18:07 Página 15

EAU11030
Turn signal indicator lights “c” and
“d”
The corresponding indicator light flas-
hes when the turn signal switch is
pushed to the left or right.
EAU11080
High beam indicator light “j”
This indicator light comes on when
the high beam of the headlight is swit-
ched on.
EAU11130
2-stroke engine oil level warning
light “z”
This warning light comes on when the
2-stroke engine oil level is low.
The electrical circuit of the warning
light can be checked according to the
following procedure.
1. Turn the key to “ON”.
2. Shift the transmission into the
neutral position.
3. If the warning light does not
come on, have a Yamaha dealer
check the electrical circuit.
ECA11570
CAUTION
Do not operate the motorcycle until
you know that the 2-stroke engine
oil level is sufficient.
NOTE:
Even if the 2-stroke engine oil level is
sufficient, the warning light may flic-
ker when riding on a slope or during
sudden acceleration or deceleration,
but this is not a malfunction.
EAU11430
Coolant temperature warning light
“y”
This warning light comes on when the
engine overheats. When this occurs,
stop the engine immediately and
allow the engine to cool.
ECA10020
CAUTION
Do not operate the engine if it is
overheated.
EAUM1090
Speedometer unit
1. Speedometer unit
2. Fuel gauge
3. Clock
4. Odometer (TOTAL/TRIP)
5. “TRIP” button
The speedometer unit is equipped
with a speedometer, an odometer and
a tripmeter. The speedometer shows
riding speed. The odometer shows
the total distance traveled. The trip-
meter shows the distance traveled
since it was last set to zero.
Pushing the reset button switches the
display between the odometer mode
“TOTAL” and the tripmeter mode
“TRIP”. To reset the tripmeter, enter
the “TRIP” mode, and then hold down
j
d
z
c4050
30
10 2060
70
80
0
y
00000.0
23:08TOTALExF
3
INSTRUMENT AND CONTROL FUNCTIONS
3-2
14
3
2 5
5RW-F8199-E3.qxd 08/09/2005 18:07 Página 16

the reset button for at least two
second.
The tripmeter can be used together
with the fuel gauge to estimate the
distance that can be traveled with a
full tank of fuel. This information will
enable you to plan future fuel stops.
EAU12140
Fuel gauge
The fuel gauge indicates the amount
of fuel in the fuel tank. The needle
moves towards “E” (Empty) as the
fuel level decreases. When the needle
reaches “E”, refuel as soon as possi-
ble.
NOTE:
Do not allow the fuel tank to empty
itself completely.
EAUS1010
Clock
To set the clock
1. Turn the key to “f”.
2. Set the odometer/tripmeter dis-
play to “TOTAL” by pushing the
“SET” button.3. Push the “SET” button for at least
two seconds.
4. When the hours digits start flas-
hing, push the “SET” button to
set the hours.
5. Push the “SET” button for at least
two seconds and the minutes
digits will start flashing.
6. Push the “SET” button to set the
minutes.
7. Push the “SET” button for at least
two seconds to start the clock
and return to the odometer/trip-
meter mode.
NOTE:
The clock is displayed only when the
key is in the “f” position.
EAU12343
Handlebar switches
1. Horn switch
2. Turn signal switch
3. Dimmer swith
EAU12400
Dimmer switch “j/k”
Set this switch to “j” for the high
beam and to “k” for the low beam.
EAU12440
Turn signal switch “TURN”
To signal a right-hand turn, push this
switch to the right. To signal a left-
hand turn, push this switch to the left.
When released, the switch returns to
the center position. To cancel the turn
signal lights, push the switch in after it
has returned to the center position.
kb
a
3
INSTRUMENT AND CONTROL FUNCTIONS
3-3
13
2
5RW-F8199-E3.qxd 08/09/2005 18:07 Página 17