2007 YAMAHA CYGNUS 125 turn signal

OPERATION AND IMPORTANT RIDING POINTS
5-2
2
3
4
56
7
8
9

EAU16760
Starting off
NOTE:

Before starting off, allow the engine to
warm up.
1. While pulling the rear brake lever
with your left hand and holding the
grab bar with your right hand, push
the scooter off the centerstand.
2. Sit astride the seat, and then ad-
just the rear view mirrors.
3. Switch the turn signal on.
4. Check for oncoming traffic, and
then slowly turn the throttle grip (on
the right) in order to take off.
5. Switch the turn signal off.
EAU16780
Acceleration and deceleration
The speed can be adjusted by opening
and closing the throttle. To increase the
speed, turn the throttle grip in direction
(a). To reduce the speed, turn the throt-
tle grip in direction (b).
EAU16791
Braking
1. Close the throttle completely.
2. Apply both front and rear brakes
simultaneously while gradually in-
creasing the pressure.
WARNING

EWA10300

Avoid braking hard or suddenly
(especially when leaning over to
one side), otherwise the scooter
may skid or overturn.

Railroad crossings, streetcar
rails, iron plates on road con-
struction sites, and manhole
covers become extremely slip-
pery when wet. Therefore, slow
down when approaching such
areas and cross them with cau-
tion.

Keep in mind that braking on a
wet road is much more difficult.

Ride slowly down a hill, as brak-
ing downhill can be very diffi-
cult.
ZAUM00**
(a)(b)

PERIODIC MAINTENANCE AND MINOR REPAIR
6-24
2
3
4
5
67
8
9

EAUT1914
Replacing the fuses
The main fuse box is located above the
battery.
The fuse box, which contains the fuses
for the individual circuits, is located in
the storage compartment. (See
page 3-10.)If a fuse is blown, replace it as follows.
1. Turn the key to “OFF” and turn off
the electrical circuit in question.
2. Remove the blown fuse, and then
install a new fuse of the specified
amperage.
CAUTION:

ECAT1061

Do not use a fuse of a higher
amperage rating than recom-
mended to avoid causing exten-
sive damage to the electrical
system and possibly a fire.

After removing and installing
the main fuse, be sure to turn
the main switch from “ON” to
“OFF” three times in 3 seconds
intervals to initialize the idle
speed control system.
3. Turn the key to “ON” and turn on
the electrical circuit in question to
check if the device operates.
1. Main fuse
ZAUM00**
1

1. Lid
2. Backup fuse
3. Ignition fuse
4. Signaling system fuse
5. Taillight fuse
6. Headlight fuse
ZAUM00**
1
234
5
6

Specified fuses:
Main fuse:
20.0 A
Headlight fuse:
15.0 A
Signaling system fuse:
15.0 A
Ignition fuse:
7.5 A
Backup fuse:
7.5 A
Taillight fuse:
7.5 A

PERIODIC MAINTENANCE AND MINOR REPAIR
6-26
2
3
4
5
67
8
9 fected. Thoroughly clean off any dirt
and fingerprints on the headlight
bulb using a cloth moistened with al-

cohol or thinner.
6. Install the headlight bulb cover,
and then connect the coupler.
7. Install the panel.
8. Have a Yamaha dealer adjust the
headlight beam if necessary.
EAUT1891
Replacing a front turn signal
light bulb
CAUTION:

ECA10670
It is advisable to have a Yamaha
dealer perform this job.
1. Place the scooter on the center-
stand.
2. Remove panel A. (See page 6-6.)
3. Remove the socket (together with
the bulb) by turning it counter-
clockwise.
4. Remove the defective bulb by
pushing it in and turning it counter-
clockwise.5. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
6. Install the socket (together with the
bulb) by turning it clockwise.
7. Install the panel.
1. Turn signal light bulb
2. Socket
ZAUM00**
1
2

PERIODIC MAINTENANCE AND MINOR REPAIR
6-27
1
2
3
4
5
6
7
8
9

EAUT1922
Replacing the tail/brake light
bulb or a rear turn signal light
bulb
Tail/brake light bulb
1. Remove the tail/brake light lens by
removing the screws.
2. Remove the defective bulb by
pushing it in and turning it counter-
clockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing thescrews.
Rear turn signal light bulb
1. Remove the tail/brake light lens by
removing the screws.
2. Remove the turn signal light lens
by removing the screws.
3. Remove the defective bulb by
pushing it in and turning it counter-
clockwise.
4. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
5. Install the turn signal light lens by
installing the screws.
6. Install the tail/brake light lens by in-
stalling the screws.
CAUTION:

ECA10680
Do not overtighten the screws, oth-
erwise the lens may break.
EAUT1962
Replacing an auxiliary light
bulb
This model is equipped with two auxil-
iary lights. If an auxiliary light bulb burns
out, replace it as follows.
1. Remove panel B. (See page 6-6.)
2. Remove the auxiliary light socket
(together with the bulb) by turning
it counterclockwise.
3. Remove the defective bulb by pull-
ing it out.
4. Insert a new bulb into the socket.
5. Install the auxiliary light socket (to-
gether with the bulb) by turning it
clockwise.
1. Tail/brake light lens
2. Turn signal light lens
3. Rear turn signal light bulb
4. Tail/brake light bulb
ZAUM00**3
1
2
4

1. Auxiliary light bulb
2. Socket
ZAUM00**
12

SPECIFICATIONS
8-2
1
2
3
4
5
6
7
8
9

Trail:
90.0 mm (3.54 in)
Front tire:
Type:
Tubeless
Size:
110/70-12 47L
Manufacturer/model:
CHENG SHIN / C-992N
Rear tire:
Type:
Tubeless
Size:
120/70-12 58L
Manufacturer/model:
CHENG SHIN / C-6007
Maximum load:
172 kg (379 lb)
* (Total weight of rider, passenger, cargo
and accessories)
Tire air pressure (measured on cold
tires):
Loading condition:
0–90 kg (0–198 lb)
Front:
175 kPa (25 psi) (1.75 kgf/cm
2

)
Rear:
200 kPa (29 psi) (2.00 kgf/cm
2

)
Loading condition:
90–172 kg (198–379 lb)
Front:
200 kPa (29 psi) (2.00 kgf/cm
2

)Rear:
225 kPa (33 psi) (2.25 kgf/cm
2

)
Front wheel:
Wheel type:
Cast wheel
Rim size:
J12 X MT2.75
Rear wheel:
Wheel type:
Cast wheel
Rim size:
J12 X MT3.00
Front brake:
Type:
Single disc brake
Operation:
Right hand operation
Recommended fluid:
DOT 4
Rear brake:
Type:
Drum brake
Operation:
Left hand operation
Front suspension:
Type:
Telescopic fork
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
78.0 mm (3.07 in)
Rear suspension:
Type:
Unit swing
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
95.5 mm (3.76 in)
Electrical system:
Ignition system:
Transistorized coil ignition (digital)
Charging system:
AC magneto
Battery:
Model:
MF (YT7B-BS)
Voltage, capacity:
12 V, 6.5 Ah
Headlight:
Bulb type:
Halogen bulb
Bulb voltage, wattage
×
quantity:
Headlight:
12 V, 60 W/55.0 W
×
1
Tail/brake light:
12 V, 5.0 W/21.0 W
×
1
Front turn signal light:
12 V, 10.0 W
×
2
Rear turn signal light:
12 V, 10.0 W
×
2
Auxiliary light:
12 V, 5.0 W
×
2
License plate light:
12 V, 5.0 W
×
1

SPECIFICATIONS
8-3
2
3
4
5
6
7
89

Meter lighting:
LED x 2
High beam indicator light:
LED x 1
Turn signal indicator light:
LED x 1
Fuses:
Main fuse:
20.0 A
Headlight fuse:
15.0 A
Taillight fuse:
7.5 A
Signaling system fuse:
15.0 A
Ignition fuse:
7.5 A
Backup fuse:
7.5 A

INDEX
A
Acceleration and deceleration................... 5-2
Air filter and V-belt case air filter
elements ............................................... 6-12
Auxiliary light bulb, replacing .................. 6-27
B
Battery..................................................... 6-22
Brake fluid, changing .............................. 6-19
Brake fluid level, checking ...................... 6-18
Brake lever, front....................................... 3-6
Brake lever, rear ....................................... 3-7
Brake levers, lubricating.......................... 6-20
Brake pads and shoes, checking ............ 6-17
Braking ...................................................... 5-2
C
Cables, checking and lubricating ............ 6-19
Care .......................................................... 7-1
Catalytic converter .................................... 3-9
Centerstand and sidestand, checking and
lubricating ............................................. 6-20
D
Dimmer switch .......................................... 3-6
E
Engine break-in ......................................... 5-3
Engine oil and oil strainer.......................... 6-9
Engine trouble warning light...................... 3-3
F
Final transmission oil .............................. 6-11
Front fork, checking ................................ 6-21
Fuel ........................................................... 3-8
Fuel consumption, tips for reducing .......... 5-3
Fuel tank cap ............................................ 3-7
Fuses, replacing...................................... 6-24
H
Handlebar switches ...................................3-5
Headlight bulb, replacing .........................6-25
High beam indicator light ...........................3-2
Horn switch ................................................3-6
I
Identification numbers................................9-1
Indicator and warning lights .......................3-2
K
Keyhole cover ............................................3-2
Key identification number ..........................9-1
Kickstarter ..................................................3-9
M
Main switch ................................................3-1
Matte color, caution ...................................7-1
Model label ................................................9-2
Multi-function display .................................3-3
P
Panels, removing and installing .................6-6
Parking.......................................................5-4
Part locations .............................................2-1
Periodic maintenance and lubrication
chart ........................................................6-3
Pre-operation check list .............................4-2
R
Rear brake lever free play, adjusting .......6-16
S
Safe-riding points .......................................1-4
Safety information ......................................1-1
Seat ...........................................................3-9
Sidestand .................................................3-11
Sidestand switch operation check ...........3-12
Spark plug, checking .................................6-7
Specifications.............................................8-1Speedometer ............................................. 3-3
Starting off ................................................. 5-2
Starting the engine .................................... 5-1
Start switch ................................................ 3-6
Steering, checking ................................... 6-21
Storage ...................................................... 7-3
Storage compartments ............................ 3-10
T
Tail/brake light bulb or rear turn signal
light bulb, replacing ............................... 6-27
Throttle cable free play, checking............ 6-14
Throttle grip and cable, checking and
lubricating .............................................. 6-20
Tires ........................................................ 6-14
Tool kit ....................................................... 6-1
Troubleshooting....................................... 6-28
Troubleshooting chart.............................. 6-29
Turn signal indicator light .......................... 3-2
Turn signal light bulb (front), replacing .... 6-26
Turn signal switch...................................... 3-6
V
Valve clearance ....................................... 6-14
Vehicle identification number .................... 9-1
W
Wheel bearings, checking ....................... 6-22
Wheels .................................................... 6-16