2007 TOYOTA TUNDRA seats

1092007 TUNDRA from Jul. ’07 Prod. (OM34463U)
Do not modify or remove the front
seats.
Do not kick the front passenger
seat or subject it to severe impact.
Otherwise, the SRS warning light
may come on to indicate a malfunc-
tion of the detection system. In this
case, contact your Toyota dealer im-
mediately.
The passenger airbag on−off indicator light
may indicate “ON” (the front passenger
airbag and side airbag on the front
passenger seat may deploy) even if
observing the above cautions, when a
child sits in, or a forward −facing child
restraint system is installed on the front
passenger seat. Refer to all the cautions
in “—SRS driver airbag and front
passenger airbag” on page 75, “—SRS
side airbags and curtain shield airbags” on
page 94 and “Child restraint” on page 114
in this Section. Your vehicle is equipped with a front
passenger occupant classification sys-
tem. The system detects conditions
1—4 (Shown in the table on page 111)
Based on these conditions, the systems
below are activated or deactivated:
Front passenger airbag
Side airbag on the right front passen-
ger seat
Front passenger ’s seat belt pretension-
er
The system monitors the weight and
load on the right front passenger seat,
and the seat belt buckle switch to de-
termine conditions 1—4.
In order to ensure the system detects
the conditions correctly:
Do not place a heavy load on the right
front passenger seat or the seatback
table, etc.
Do not attach a commercial seatback
table or other heavy item to the back
of the right front passenger seat.
Do not apply pressure to the right front
passenger seat by resting hands or
legs on the seatback.
XS13025a
The passenger airbag onoff indicator
light indicates the actuation of the front
passenger airbag, side airbag on the
front passenger seat and front passen-
ger seat belt pretensioner.
The passenger airbag onoff indicator
light will indicate “ON” and “OFF”
when the ignition switch is turned to
the “ON” position. After about four sec-
onds, it will go off. After that, the front
passenger occupant classification sys-
tem operates and judges whether to in-
dicate “ON” or “OFF”.
—Front passenger occupant
classification system
(Double cab and Crew Max models)

11 32007 TUNDRA from Jul. ’07 Prod. (OM34463U)
When it is unavoidable to install the
forwardfacing child restraint sys-
tem on the front passenger seat,
install the child restraint system on
the right front passenger seat in
the proper order. (As for the instal-
lation order, see “—Installation with
seat belt” on page 127 in this Sec-
tion.)
Do not modify or remove the front
seats.
Do not kick the front passenger
seat or subject it to severe impact.
Otherwise, the SRS warning light
may come on to indicate a malfunc-
tion of the detection system. In this
case, contact your Toyota dealer im-
mediately.
The passenger airbag on−off indicator light
may indicate “ON” (the front passenger
airbag and side airbag on the front
passenger seat may deploy) even if
observing the above cautions, when a
child sits in, or a forward −facing child
restraint system is installed on the front
passenger seat. Refer to all the cautions
in “—SRS driver airbag and front
passenger airbag” on page 86, “—SRS
side airbags and curtain shield airbags” on
page 94 and “Child restraint” on page 114.
XS13029
The roll sensing of curtain shield air-
bags off switch (“RSCA OFF” switch)
can turn off the curtain shield airbags
and seat belt pretensioners in a vehicle
rollover. This switch should only be
used if inflation is not desired (such as
extreme offroad driving).
—Roll sensing of curtain
shield airbags off switch

11 62007 TUNDRA from Jul. ’07 Prod. (OM34463U)
Do not use the seat belt extender
when installing a child restraint
system on the front or rear passen-
ger seat. If installing a child re-
straint system with the seat belt
extender connected to the seat belt,
the seat belt will not securely hold
the child restraint system, which
could cause death or serious injury
to the child or other passengers in
the event of collision.
Make sure you have complied with
all installation instructions provided
by the child restraint manufacturer
and that the system is properly se-
cured. If it is not secured properly,
it may cause death or serious injury
to the child in the event of a sud-
den stop or accident.
A child restraint system for a small
child or baby must itself be properly
restrained on the seat with the lap por-
tion of the lap/shoulder belt. You must
carefully consult the manufacturer ’s
instructions which accompany the child
restraint system.
To provide proper restraint, use a child
restraint system following the manufactur-
er ’s instructions about the appropriate age
and size of the child for the child restraint
system.
Install the child restraint system correctly
following the instructions provided by its
manufacturer. General directions are also
provided under the following illustrations.
The child restraint system should be
installed in the rear seat if your vehicle
is equipped with rear seats. According to
accident statistics, the child is safer when
properly restrained in the rear seat than
in the front seat.
When not using the child restraint system,
keep it secured with the seat belt or place
it somewhere other than the passenger
compartment. This will prevent it from in-
juring passengers in the event of a sud-
den stop or accident.Child restraint systems are classified into
the following 3 types depending on the
child’s age and size.
(A) Infant seat
(B) Convertible seat
(C) Booster seat
Install the child restraint system following
the instructions provided by its manufac-
turer.
Your vehicle has anchor brackets for se-
curing the top strap of a child restraint
system.
For instructions about how to use the an-
chor bracket, see “—Using a top strap” on
page 138 or 141 in this Section.
The child restraint lower anchorages
approved for your vehicle may also be
used. See “—Installation with child
restraint lower anchorages” on page 146 or
148 in this Section.
—Child restraint system
—Types of child restraint
system

1282007 TUNDRA from Jul. ’07 Prod. (OM34463U)
XS13056
Do not install a child restraint sys-
tem on the rear seat if it interferes
with the lock mechanism of the
front seats. Otherwise, the child or
front seat occupant, may be killed
or seriously injured in case of sud-
den braking or a collision.
If the driver ’s seat position does
not allow sufficient space for safe
installation, install the child re-
straint system on the rear right
seat. Child restraint system
installed on the rear seat should
not contact the front seatbacks.
XS13193
Same angle
Same position
Crew Max models: When installing
a child restraint system in the rear
seat center position, adjust both
seat cushions to the same position
and align both seatbacks at the
same angle. Otherwise, the child re-
straint system cannot be securely
restrained and this may cause death
or serious injuries in a collision.
XS13057
To install the infant seat: 1. Run the lap and shoulder belt through or around the infant seat following the
instructions provided by its manufactur-
er and insert the tab into the buckle
taking care not to twist the belt. Keep
the lap portion of the belt tight.

1332007 TUNDRA from Jul. ’07 Prod. (OM34463U)
Do not allow the child to lean his/
her head or any part of his/her
body against the door or the area
of the seat, front or rear pillar or
roof side rail from which the side
airbags or curtain shield airbags
deploy even if the child is seated in
the child restraint system. It is dan-
gerous if the side airbag and cur-
tain shield airbag inflate, and the
impact could cause death or seri-
ous injury to the child.
XS13065
Do not install a child restraint sys-
tem on the rear seat if it interferes
with the lock mechanism of the
front seats. Otherwise, the child or
front seat occupants may be killed
or seriously injured in case of sud-
den braking or a collision.
If the driver ’s seat position does
not allow sufficient space for safe
installation, install the child re-
straint system on the rear right
seat. Child restraint system
installed on the rear seat should
not contact the front seatbacks.
XS13194
Same angle
Same position
Crew Max models: When installing
a child restraint system in the rear
seat center position, adjust both
seat cushions to the same position
and align both seatbacks at the
same angle. Otherwise, the child re-
straint system cannot be securely
restrained and this may cause death
or serious injuries in a collision.

1392007 TUNDRA from Jul. ’07 Prod. (OM34463U)
XS13076a
Symbol mark
Anchor brackets
Bench seats
XS13144aSymbol mark Anchor
bracket
Separate seats
Use the anchor bracket on the back panel
to attach the top strap.
Anchor brackets are installed for each
passenger seating position.
This symbol indicates the locations of the
anchor brackets.
XS13077
TO USE THE ANCHOR BRACKET:
1. Remove the passenger head re- straint.

1432007 TUNDRA from Jul. ’07 Prod. (OM34463U)
XS13088b
Routing
device
3. Fix the child restraint system withthe seat belt.
Route the top strap through the
routing device as shown in the il-
lustration.
XS13089b
Inner anchor
strap ring
4. Latch the hook onto the inner an-chor strap ring and tighten the top
strap.
XS13090b
5. Lower the head restraints.
For instructions on installing the child re-
straint system, see “Child restraint” on
page 114 in this Section.
CAUTION
Make sure the top strap is securely
latched, and check that the child re-
straint system is secure by pushing
and pulling it in different directions.
Follow all the installation instructions
provided by its manufacturer.
6. If two child seats will be installed, use the outboard seating positions.

1462007 TUNDRA from Jul. ’07 Prod. (OM34463U)
XS13202
4. Replace the head restraint.
5. If two child seats will be installed,use the outboard seating positions.
XS13091
Lower anchorages for the child restraint
systems complying with the FMVSS225
or CMVSS210.2 specifications are
installed in the front seat.
The anchorages are installed in the gap
between the seat cushion and seatback of
the right side of the seat as shown in the
illustration.
Child restraint systems complying with the
FMVSS213 or CMVSS213 specification
can be fixed to these anchorages. In this
case, it is not necessary to fix the child
restraint system with a seat belt on the
vehicle.
XS1314312th lock
position 1st lock
position
CHILD RESTRAINT SYSTEM
INSTALLATION
1. Fold down the seatback and back to the 1st lock position until it locks
into place. Adjust the seatback to
the 12th lock position.
Make sure the seatback is locked secure-
ly.
—Installation with child
restraint lower anchorages
(Regular cab models)